lock NISSAN TEANA 2008 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TEANA, Model: NISSAN TEANA 2008Pages: 5121, PDF Size: 69.03 MB
Page 1279 of 5121
![NISSAN TEANA 2008 Service Manual DOOR LOCK ACTUATOR
DLK-63
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REAR LH : Component Function CheckINFOID:0000000003794855
1.CHECK FUNCTION
1. Use CONSUL](/img/5/57391/w960_57391-1278.png "NISSAN TEANA 2008 Service Manual DOOR LOCK ACTUATOR
DLK-63
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REAR LH : Component Function CheckINFOID:0000000003794855
1.CHECK FUNCTION
1. Use CONSUL")
DOOR LOCK ACTUATOR
DLK-63
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REAR LH : Component Function CheckINFOID:0000000003794855
1.CHECK FUNCTION
1. Use CONSULT-III to perform Active Test (“DOOR LOCK”).
2. Touch “ALL LCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Door lock actuator is OK.
NO >> Refer to DLK-63, "
REAR LH : Diagnosis Procedure".
REAR LH : Diagnosis ProcedureINFOID:0000000003794856
1.CHECK DOOR LOCK ACTUATOR OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock assembly LH.
3. Check voltage between rear door lock assembly LH harness connector and ground.
Is the inspection result normal?
YES >> Replace rear door lock assembly LH. Refer to DLK-202, "DOOR ASSEMBLY : Removal and
Installation".
NO >> GO TO 2.
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and rear door lock assembly LH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
REAR RH
REAR RH : DescriptionINFOID:0000000003794857
Locks/unlocks the door with the signal from BCM.
REAR RH : Component Function CheckINFOID:0000000003794858
1.CHECK FUNCTION
(+)
(–) ConditionVoltage (V)
(Approx.) Rear door lock assembly LH
Connector Terminal
D851
GroundDoor lock and
unlock switchLOCK 0 → Battery voltage → 0
2 UNLOCK 0 → Battery voltage → 0
BCM Rear door lock assembly LH
Continuity
Connector Terminal Connector Terminal
M1198
D851
Existed
10 2
BCM
GroundContinuity
Connector Terminal
M1198
Not existed
10
Page 1280 of 5121
![NISSAN TEANA 2008 Service Manual DLK-64
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
1. Use CONSULT-III to perform Active Test (“DOOR LOCK”).
2. Touch “ALL LCK” or “ALL UNLK” to check that it wo](/img/5/57391/w960_57391-1279.png "NISSAN TEANA 2008 Service Manual DLK-64
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
1. Use CONSULT-III to perform Active Test (“DOOR LOCK”).
2. Touch “ALL LCK” or “ALL UNLK” to check that it wo")
DLK-64
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
1. Use CONSULT-III to perform Active Test (“DOOR LOCK”).
2. Touch “ALL LCK” or “ALL UNLK” to check that it works normally.
Is the inspection result normal?
YES >> Door lock actuator is OK.
NO >> Refer to DLK-64, "
REAR RH : Diagnosis Procedure".
REAR RH : Diagnosis ProcedureINFOID:0000000003794859
1.CHECK DOOR LOCK ACTUATOR OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock assembly RH.
3. Check voltage between rear door lock assembly RH harness connector and ground.
Is the inspection result normal?
YES >> Replace rear door lock assembly RH. Refer to DLK-208, "DOOR ASSEMBLY : Removal and
Installation".
NO >> GO TO 2.
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and rear door lock assembly RH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
(+)
(–)Condition of door lock and
unlock switchVoltage (V)
(Approx.) Rear door lock assembly RH
Connector Terminal
D1051
GroundUNLOCK 0 → Battery voltage → 0
2LOCK0 → Battery voltage → 0
BCM Rear door lock assembly RH
Continuity
Connector Terminal Connector Terminal
M1198
D1052
Existed
10 1
BCM
GroundContinuity
Connector Terminal
M1198
Not Existed
10
Page 1281 of 5121
![NISSAN TEANA 2008 Service Manual TRUNK LID OPENER ACTUATOR
DLK-65
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID OPENER ACTUATOR
DescriptionINFOID:0000000003794860
Trunk lid opener act](/img/5/57391/w960_57391-1280.png "NISSAN TEANA 2008 Service Manual TRUNK LID OPENER ACTUATOR
DLK-65
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID OPENER ACTUATOR
DescriptionINFOID:0000000003794860
Trunk lid opener act")
TRUNK LID OPENER ACTUATOR
DLK-65
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID OPENER ACTUATOR
DescriptionINFOID:0000000003794860
Trunk lid opener actuator open trunk lid from BCM.
Component Function CheckINFOID:0000000003794861
1.CHECK FUNCTION
1. Perform Active Test (“TRUNK/GLASS HATCH”) with CONSULT-III.
2. Touch “OPEN” and check that trunk lid opens.
Is the inspection result normal?
YES >> Trunk lid opener actuator is OK.
NO >> Refer to DLK-65, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003794862
1.CHECK TRUNK LID OPENER INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly.
3. Check voltage between trunk lid lock assembly harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK TRUNK LID OPENER ACTUATOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and trunk lid lock assembly (trunk lid opener actuator)
harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK TRUNK LID OPENER ACTUATOR GROUND CIRCUIT
Check continuity between trunk lid lock assembly (trunk lid opener actuator) harness connector and ground.
(+)
(–) ConditionVoltage (V)
(Approx.) Trunk lid lock assembly
(trunk lid opener actuator)
Connector Terminal
T5 2 Ground Trunk lid opener switch is ON 0 → Battery voltage → 0
BCMTrunk lid lock assembly
(trunk lid opener actuator)
Continuity
Connector Terminal Connector Terminal
M120 23 T5 2 Existed
BCM
GroundContinuity
Connector Terminal
M120 23 Not existed
Page 1282 of 5121
![NISSAN TEANA 2008 Service Manual DLK-66
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID OPENER ACTUATOR
Is the inspection normal?
YES >> Replace trunk lid lock assembly. Refer to DLK-214, "TRUNK LID ASSEMBLY : Removal](/img/5/57391/w960_57391-1281.png "NISSAN TEANA 2008 Service Manual DLK-66
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID OPENER ACTUATOR
Is the inspection normal?
YES >> Replace trunk lid lock assembly. Refer to DLK-214, \"TRUNK LID ASSEMBLY : Removal")
DLK-66
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
TRUNK LID OPENER ACTUATOR
Is the inspection normal?
YES >> Replace trunk lid lock assembly. Refer to DLK-214, "TRUNK LID ASSEMBLY : Removal and
Installation"
NO >> Repair or replace harness.
Trunk lid lock assembly
GroundContinuity
Connector Terminal
T5 3 Existed
Page 1288 of 5121
![NISSAN TEANA 2008 Service Manual DLK-72
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH
DescriptionINFOID:0000000003794874
Transmits lock/unlock operation to BCM.
Component Function CheckI](/img/5/57391/w960_57391-1287.png "NISSAN TEANA 2008 Service Manual DLK-72
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH
DescriptionINFOID:0000000003794874
Transmits lock/unlock operation to BCM.
Component Function CheckI")
DLK-72
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH
DescriptionINFOID:0000000003794874
Transmits lock/unlock operation to BCM.
Component Function CheckINFOID:0000000003794875
1.CHECK FUNCTION
Check door request switch (“REQ SW-DR” or “REQ SW-AS”) in Data Monitor mode.
Is the inspection result normal?
YES >> Door request switch is OK.
NO >> Refer to DLK-72, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003794876
1.CHECK BCM OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect malfunctioning front outside handle (request switch) connector.
3. Check signal between malfunctioning front outside handle (request switch) harness connector and ground
with oscilloscope.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK DOOR REQUEST SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and malfunctioning front outside handle (request
switch) harness connector.
3. Check continuity between BCM harness connector and ground.
Monitor item Condition
DR REQ SW
AS REQ SWDoor request switch is pressed: ON
Door request switch is released: OFF
(+)
(–)Signal
(Reference value) Front outside handle (request switch)
Connector Terminal
LH D11
1 Ground
RH D50
JMKIA0059GB
BCM Front outside handle (request switch)
Continuity
Connector Terminal Connector Terminal
M122101 LH D11
1 Existed
100 RH D50
Page 1292 of 5121
![NISSAN TEANA 2008 Service Manual DLK-76
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
TRUNK ROOM LAMP SWITCH
TRUNK ROOM LAMP SWITCH
DescriptionINFOID:0000000003840907
Detects trunk lid open/close condition.
Component Function](/img/5/57391/w960_57391-1291.png "NISSAN TEANA 2008 Service Manual DLK-76
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
TRUNK ROOM LAMP SWITCH
TRUNK ROOM LAMP SWITCH
DescriptionINFOID:0000000003840907
Detects trunk lid open/close condition.
Component Function")
DLK-76
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
TRUNK ROOM LAMP SWITCH
TRUNK ROOM LAMP SWITCH
DescriptionINFOID:0000000003840907
Detects trunk lid open/close condition.
Component Function CheckINFOID:0000000003840908
1.CHECK FUNCTION
With CONSULT-III
Check (“TRNK/HAT MNTR”) in Data Monitor mode with CONSULT-III.
Is the inspection result normal?
YES >> Trunk room lamp switch is OK.
NO >> Refer to DLK-77, "
Component Inspection".
Diagnosis ProcedureINFOID:0000000003840909
1.CHECK TRUNK ROOM LAMP SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly.
3. Check signal between BCM connector and ground with oscilloscope.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK TRUNK ROOM LAMP SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM connector and trunk lid lock assembly connector.
3. Check continuity between BCM connector and ground.
Monitor item Condition
TRNK/HAT MNTROPEN : ON
CLOSE : OFF
(+)
(–)Trunk
conditionSignal
(Reference value) Trunk lid lock assembly
Connector Terminal
T5 1 GroundOPEN 0
CLOSE
JPMIA0011GB
BCM Trunk lid lock assembly
Continuity
Connector Terminal Connector Terminal
M121 50 T5 1 Existed
BCM
GroundContinuity
Connector Terminal
M121 50 Not existed
Page 1293 of 5121
![NISSAN TEANA 2008 Service Manual TRUNK ROOM LAMP SWITCH
DLK-77
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and I](/img/5/57391/w960_57391-1292.png "NISSAN TEANA 2008 Service Manual TRUNK ROOM LAMP SWITCH
DLK-77
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, \"Removal and I")
TRUNK ROOM LAMP SWITCH
DLK-77
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK TRUNK ROOM LAMP SWITCH GROUND CIRCUIT
Check continuity between trunk lid lock assembly connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK TRUNK ROOM LAMP SWITCH
Refer to DLK-77, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace trunk lid lock assembly. Refer to DLK-214, "
TRUNK LID ASSEMBLY : Removal and
Installation".
5.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END.
Component InspectionINFOID:0000000003840910
1.CHECK TRUNK ROOM LAMP SWITCH
1. Turn ignition switch OFF.
2. Disconnect trunk lid lock assembly connector.
3. Check trunk room lamp switch.
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Replace trunk lid lock assembly. Refer to DLK-214, "
TRUNK LID ASSEMBLY : Removal and
Installation".
Trunk lid lock assembly
GroundContinuity
Connector Terminal
T5 3 Existed
Trunk lid lock assembly
Condition Continuity
Te r m i n a l
13Trunk lidOPEN Existed
CLOSE Not existed
Page 1294 of 5121
![NISSAN TEANA 2008 Service Manual DLK-78
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
UNLOCK SENSOR
UNLOCK SENSOR
DescriptionINFOID:0000000003794882
Detects door lock condition of driver door.
Component Function CheckINFOID:00](/img/5/57391/w960_57391-1293.png "NISSAN TEANA 2008 Service Manual DLK-78
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
UNLOCK SENSOR
UNLOCK SENSOR
DescriptionINFOID:0000000003794882
Detects door lock condition of driver door.
Component Function CheckINFOID:00")
DLK-78
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
UNLOCK SENSOR
UNLOCK SENSOR
DescriptionINFOID:0000000003794882
Detects door lock condition of driver door.
Component Function CheckINFOID:0000000003794883
1.CHECK FUNCTION
Check unlock sensor (“DOOR STAT-DR”) in “Data Monitor” mode.
Is the inspection result normal?
YES >> Unlock sensor is OK.
NO >> Refer to DLK-78, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003794884
1.CHECK BCM OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly (driver side) (unlock sensor) connector.
3. Check signal between front door lock assembly (driver side) (unlock sensor) harness connector and
ground with oscilloscope.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK UNLOCK SENSOR CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and front door lock assembly (driver side) (unlock sen-
sor) harness connector.
3. Check continuity between BCM harness connector and ground.
Monitor item Condition
DOOR STAT-DRFront door lock (driver side) LOCK: OFF
Front door lock (driver side) UNLOCK: ON
(+)
(–)Signal
(Reference value) Front door lock assembly (driver side) (unlock sensor)
Connector Terminal
D9 3 Ground
JPMIA0012GB
BCMFront door lock assembly
(driver side) (unlock sensor)
Continuity
Connector Terminal Connector Terminal
M123 119 D9 3 Existed
BCM
GroundContinuity
Connector Terminal
M123 119 Not existed
Page 1295 of 5121
![NISSAN TEANA 2008 Service Manual UNLOCK SENSOR
DLK-79
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installati](/img/5/57391/w960_57391-1294.png "NISSAN TEANA 2008 Service Manual UNLOCK SENSOR
DLK-79
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, \"Removal and Installati")
UNLOCK SENSOR
DLK-79
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) (unlock sensor) harness connector and
ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK UNLOCK SENSOR
Refer to DLK-79, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace front door lock assembly (driver side). Refer to DLK-214, "
TRUNK LID ASSEMBLY :
Removal and Installation".
5.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000003794885
1.CHECK UNLOCK SENSOR
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly (driver side) (unlock sensor).
3. Check front door lock assembly (driver side) (unlock sensor) terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace front door lock assembly (driver side). Refer to DLK-202, "
DOOR ASSEMBLY : Removal
and Installation".
Front door lock assembly (driver side) (unlock sensor)
GroundContinuity
Connector Terminal
D9 4 Existed
Front door lock assembly
(driver side) (unlock sensor)
Condition Continuity
Te r m i n a l
34Front door lock assembly
(driver side) (unlock sensor) Unlock Existed
Lock Not existed
Page 1296 of 5121
![NISSAN TEANA 2008 Service Manual DLK-80
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
OUTSIDE KEY ANTENNA
OUTSIDE KEY ANTENNA
DescriptionINFOID:0000000003794886
Detects whether Intelligent Key is outside the vehicle.
Integrate](/img/5/57391/w960_57391-1295.png "NISSAN TEANA 2008 Service Manual DLK-80
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
OUTSIDE KEY ANTENNA
OUTSIDE KEY ANTENNA
DescriptionINFOID:0000000003794886
Detects whether Intelligent Key is outside the vehicle.
Integrate")
DLK-80
< COMPONENT DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
OUTSIDE KEY ANTENNA
OUTSIDE KEY ANTENNA
DescriptionINFOID:0000000003794886
Detects whether Intelligent Key is outside the vehicle.
Integrated in front outside handle (LH, RH) and installed in rear bumper.
Component Function CheckINFOID:0000000003794887
1.CHECK OUTSIDE KEY ANTENNA FUNCTION
Check that Intelligent Key is in each outside key antenna detection range.
Does door lock/unlock when each request switch is pressed?
YES >> Outside key antenna is OK.
NO >> Refer to DLK-80, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003794888
1.CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground with oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation"
NO >> GO TO 2.
2.CHECK OUTSIDE KEY ANTENNA CIRCUIT
1. Disconnect BCM connector and malfunctioning outside key antenna connector.
2. Check continuity between BCM harness connector and outside key antenna harness connector.
(+)
(–) ConditionSignal
(Reference value.) BCM
Connector Terminal
M122Front LH 76, 77
GroundDoor request
switch or trunk
lid opener re-
quest switch is
pushedWhen Intelligent Key
is in the antenna de-
tection area. Front RH 74, 75
M121Rear
bumper38, 39When Intelligent Key
is not in the antenna
detection area.
JMKIA0062GB
JMKIA0063GB