ECU NISSAN TEANA 2008 Service Manual

AV-370
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
CAMERA CONTROL UNIT
JCNWM0933GB

AV
CAMERA CONTROL UNIT
AV-371
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
JCNWM0934GB

AV-434
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Initializes the AV control unit memory.
CONSULT-III Function (MULTI AV)INFOID:0000000003765848
CONSULT-III FUNCTIONS
CONSULT-III performs the following functions via the communication with the AV control unit.
CAUTION:
Be sure to turn the ignition switch OFF once after using CONSULT-III. (Navigation system may mal-
function if normally used when the ignition switch is not turned OFF after using CONSULT-III.)
AV COMMUNICATION
When “AV communication” of “CAN Diag Support Monitor” is selected, the following function will be performed.
ECU IDENTIFICATION
The part number of AV control unit is displayed.
SELF DIAGNOSTIC RESULT
 In CONSULT-III self-diagnosis, self-diagnosis results and error history are displayed collectively.
 The timing is displayed as “0” if any of the error codes [U1000], [U1010], [U1300] and [U1310] is detected.
The counter increases by 1 if the condition is normal at the next ignition switch ON cycle.
Self-diagnosis Results Display Item
JSNIA0155GB
Diagnosis mode Description
Ecu Identification The part number of AV control unit can be checked.
Self Diagnostic ResultPerforms a diagnosis on the AV control unit and a connection diagnosis for the communication
circuit of the Multi AV system, and displays the current and past malfunctions collectively.
Data Monitor The diagnosis of vehicle signal that is input to the AV control unit can be performed.
AV communicationAV&NAVI C/UDisplays the communication status from AV control unit to each unit as well as the error
counter.
AUDIO Displays the AV control unit communication status and the error counter.
Error item Detection logic Possible malfunction factor/Action to take
CAN COMM CIRCUIT [U1000]CAN communication malfunction is detect-
ed.Refer to AV- 4 4 0 , "
DiagnosisProcedure".
CONTROL UNIT (CAN) [U1010]CAN initial diagnosis malfunction is detect-
ed.
Replace the AV control unit.
Refer to AV- 6 4 8 , "
Removal and Installa-
tion". CONTROL UNIT (AV) [U1310]AV communication circuit initial diagnosis
malfunction is detected.
Control Unit FLASH-ROM [U1200]
AV control unit malfunction is detected.
CAN CONT [U1216]
AMP TEMP [U1231] BOSE amp. is detected.Replace the BOSE amp.
Refer to AV- 6 5 7 , "
Removal and Installa-
tion".

AV
AV CONTROL UNIT
AV-495
< ECU DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ECU DIAGNOSIS
AV CONTROL UNIT
Reference ValueINFOID:0000000003765966
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III data monitor item
TERMINAL LAYOUT
PHYSICAL VALUES
Display ItemDis-
playVehicle status Remarks
VHCL SPD SIGOn Vehicle speed >0 km/h (0 MPH)
Changes in indication may be delayed. This is nor-
mal.
Off Vehicle speed =0 km/h (0 MPH)
PKB SIGOn Parking brake is applied.
Changes in indication may be delayed. This is nor-
mal.
Off Parking brake is released.
ILLUM SIGOn Light switch ON.
—
Off Light switch OFF.
IGN SIGOn Ignition switch ON.
—
Off Ignition switch in ACC position.
REV SIGOn Selector lever in R position.
Changes in indication may be delayed. This is nor-
mal.
OffSelector lever in any position other
than R.
JPNIA1093ZZ
Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
6
(W/G)15
(L/B)Steering switch signal A InputIgnition
switch
ONKeep pressing SOURCE
switch. 0 V
Keep pressing switch.0.8 V
Keep pressing switch.1.5 V
Keep pressing switch.2.1 V
Keep pressing ENTER
switch.2.8 V
Except for above. 3.5 V
7
(V/W)Ground ACC power supply InputIgnition
switch
ACC— Battery voltage
9
(R/L)Ground Illumination signal InputIgnition
switch
OFFLighting switch is OFF. 0 V
Lighting switch is ON. 12.0 V

AV-496
< ECU DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
AV CONTROL UNIT
15
(L/B)GroundSteering switch signal
ground—Ignition
switch
ON—0 V
16
(GR/L)15
(L/B)Steering switch signal B InputIgnition
switch
ONKeep pressing VOL DOWN
switch.0 V
Keep pressing VOL UP
switch.0.8 V
Keep pressing switch.1.5 V
Keep pressing switch.2.1 V
Except for above. 3.5 V
19
(Y)Ground Battery power supply InputIgnition
switch
OFF— Battery voltage
20
(B/W)Ground Ground —Ignition
switch
ON—0 V
33 — FM sub Input — — —
34 — AM–FM main Input — — —
35 Ground Antenna amp. ON signal OutputIgnition
switch
ACC— 12.0 V
36
(B)Ground Composite image signal OutputIgnition
switch
ONWhen camera image or
AUX image is displayed.
37
(W)Ground Composite image ground —Ignition
switch
ON—0 V
38
(B)Ground RGB image signal (B: blue) OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
39
(R)GroundRGB image signal (G:
green)OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen. Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB2251J
SKIB2237J
SKIB2236J

AV
AV CONTROL UNIT
AV-497
< ECU DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P40
(W)Ground RGB image signal (R: red) OutputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
DISPLAY DIAGNOSIS
screen.
41
(G)Ground RGB synchronizing signal OutputIgnition
switch
ON—
42 Ground RGB synchronizing ground ——Igni-
tion
switch
ON—0 V
43
(B)Ground RGB area (YS) signal OutputIgnition
switch
ONWhen RGB image is dis-
played.5.0 V
When camera image or
AUX image is displayed.
44
(G)GroundCommunication signal
(DISP→CONT)InputIgnition
switch
ONWhen adjusting display
brightness.
45
(W)GroundHorizontal synchronizing
(HP) signalInputIgnition
switch
ON—
49 — Shield — — — —
50 Ground RGB ground ——Igni-
tion
switch
ON—0 V
55 Ground Shield — — — —Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB2238J
SKIB3603E
PKIB4948J
PKIB5039J
SKIB3601E

AV-498
< ECU DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
AV CONTROL UNIT
56
(R)GroundCommunication signal
(CONT→DISP)OutputIgnition
switch
ONWhen adjusting display
brightness.
57
(R)GroundVertical synchronizing (VP)
signalInputIgnition
switch
ON—
60
(O)Ground RGB synchronizing signal InputIgnition
switch
ON—
61 GroundRGB synchronizing signal
ground—Ignition
switch
ON—0 V
62
(W)Ground RGB image signal (B: blue) InputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
Navigation/Phone screen.
63
(R)Ground RGB image signal (R: red) InputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
Navigation/Phone screen.
64 Ground camera image ground —Ignition
switch
ON—0 V
65
(Y)Ground Camera image signal InputIgnition
switch
ONWhen camera image is dis-
played. Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
PKIB5039J
SKIB3598E
SKIB3603E
SKIB2237J
SKIB2238J
SKIB2251J

AV
AV CONTROL UNIT
AV-499
< ECU DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P66
(V)GroundComposite (DVD and AUX)
image signalInputIgnition
switch
ONWhen AUX image is dis-
played.
68
(W)GroundCamera connection recog-
nition signalInputIgnition
switch
ONConnected to camera con-
trol unit connector 0 V
Not connected to camera
control unit connector5 V
70
(B)Ground RGB ground —Ignition
switch
ON—0 V
71
(G)GroundRGB image signal (G:
green)InputIgnition
switch
ONStart confirmation/adjust-
ment mode, and then dis-
play color bar by selecting
“Color Spectrum Bar” on
Navigation/Phone screen.
73 —Composite image signal
ground—— — —
74
(G)GroundComposite (DVD and AUX)
image signal ground—Ignition
switch
ON—0 V
78
(BR)Ground Switch ground —Ignition
switch
ON—0 V
80
(B)79
(W)TEL voice signal InputIgnition
switch
ONTEL voice output.
81 — Tel voice shield — — — —
83
(R)82
(W)Stereo (DVD and AUX)
sound signal RHInputIgnition
switch
ONDVD sound signal or AUX
sound signal input
84 — Voice guidance shield — — — —
85
(B/W)Ground Ground —Ignition
switch
ON —0 V Te r m i n a l
(Wire color)Description
Condition
Reference value
(Approx.)
+ – Signal nameInput/
Output
SKIB2251J
SKIB2236J
SKIB1990E
SKIB3609E

AV-500
< ECU DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
AV CONTROL UNIT
86
(L)—CAN–HInput/
Output—— —
87
(P)—CAN–LInput/
Output—— —
88
(W)—AV communication signal
(H)Input/
Output—— —
89
(B)—AV communication signal
(L)Input/
Output—— —
90
(L)—AV communication signal
(H)Input/
Output—— —
91
(R)—AV communication signal
(L)Input/
Output—— —
99
(B)98
(G)Stereo (DVD and AUX)
sound signal LHInputIgnition
switch
ONDVD sound signal or AUX
sound input.
100 —Stereo (DVD and AUX)
sound signal shield——— —
102
(L)101
(P)Voice guidance signal InputIgnition
switch
ONVoice guidance output.
103
(SB)Ground Disk eject signal InputIgnition
switch
ONPressing the eject switch. 0 V
Except for above. 3.3 V
104
(O)Ground Ignition signal InputIgnition
switch
ON— Battery voltage
105
(P/B)Ground Reverse signal InputIgnition
switch
ONR position. 12.0 V
Other than R position. 0 V
106
(G/R)Ground Parking brake signal InputIgnition
switch
ONParking brake ON. 0 V
Parking brake OFF. 5 V
107
(V/W)GroundVehicle speed signal
(8-pulse)InputIgnition
switch
ONWhen vehicle speed is ap-
prox. 40 km/h (25MPH).NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit). Terminal
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB1990E
JSNIA0012GB

AV
AV CONTROL UNIT
AV-501
< ECU DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P109
(W)11 5
(B)Stereo sound signal front
RHOutputIgnition
switch
ONSound output.
111 — S h i e l d — — — —
11 2
(BR)11 8
(Y)Voice guidance signal OutputIgnition
switch
ONVoice guidance output.
11 3
(W)11 9
(B)Stereo sound signal front
LHOutputIgnition
switch
ONSound output. Te r m i n a l
(Wire color)Description
ConditionReference value
(Approx.)
+ – Signal nameInput/
Output
SKIB3609E
SKIB1990E
SKIB3609E