radiator NISSAN TEANA 2008 Owner's Manual

SERVICE DATA AND SPECIFICATIONS (SDS)
CO-27
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
MA
CO
N
P O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance SpecificationINFOID:0000000003793188
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit: (lmp qt)
RadiatorINFOID:0000000003793189
Unit: kPa (bar, kg/cm2, psi)
ThermostatINFOID:0000000003793190
Standard
Engine coolant capacity (With reservoir tank at “MAX” level) 9.1 (8)
Reservoir tank0.8 (3/4)
Cap relief pressureStandard 122.3 - 151.7 (1.2 - 1.5, 1.2 - 1.5, 17.7 - 22.0)
Limit 108 (1.1, 1.1, 15.6)
Leakage test pressure 157 (1.57, 1.6, 22.8)
Valve opening temperature 80.5 - 83.5°C (177 - 182°F)
Maximum valve lift 8.6 mm/95°C (0.339 in/203°F)
Valve closing temperature 77°C (171°F)

DLK-5
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P HOOD ASSEMBLY : Removal and Installation .....
192
HOOD ASSEMBLY : Adjustment ..........................193
HOOD HINGE ..........................................................193
HOOD HINGE : Exploded View ............................194
HOOD HINGE : Removal and Installation .............194
HOOD SUPPORT ROD ...........................................194
HOOD SUPPORT ROD : Exploded View .............195
HOOD SUPPORT ROD : Removal and Installa-
tion ........................................................................
195
RADIATOR CORE SUPPORT .........................196
Exploded View ......................................................196
Removal and Installation .......................................196
FRONT FENDER ..............................................199
Exploded View ......................................................199
Removal and Installation .......................................199
FRONT DOOR ..................................................201
DOOR ASSEMBLY .................................................201
DOOR ASSEMBLY : Exploded View ....................201
DOOR ASSEMBLY : Removal and Installation .....202
DOOR ASSEMBLY : Adjustment ..........................203
DOOR STRIKER ......................................................203
DOOR STRIKER : Exploded View ........................203
DOOR STRIKER : Removal and Installation ........204
DOOR HINGE ..........................................................204
DOOR HINGE : Exploded View ............................204
DOOR HINGE : Removal and Installation .............204
DOOR CHECK LINK ...............................................205
DOOR CHECK LINK : Exploded View ..................205
DOOR CHECK LINK : Removal and Installation ..205
REAR DOOR ....................................................207
DOOR ASSEMBLY .................................................207
DOOR ASSEMBLY : Exploded View ....................207
DOOR ASSEMBLY : Removal and Installation .....208
DOOR ASSEMBLY : Adjustment ..........................209
DOOR STRIKER ......................................................209
DOOR STRIKER : Exploded View ........................209
DOOR STRIKER : Removal and Installation ........210
DOOR HINGE ..........................................................210
DOOR HINGE : Exploded View ............................210
DOOR HINGE : Removal and Installation .............210
DOOR CHECK LINK ...............................................211
DOOR CHECK LINK : Exploded View ..................211
DOOR CHECK LINK : Removal and Installation ..211
TRUNK LID .......................................................213
TRUNK LID ASSEMBLY .........................................213
TRUNK LID ASSEMBLY : Exploded View ............213
TRUNK LID ASSEMBLY : Removal and Installa-
tion ........................................................................
214
TRUNK LID ASSEMBLY : Adjustment ..................215
TRUNK LID STRIKER .............................................215
TRUNK LID STRIKER : Exploded View ................216
TRUNK LID STRIKER : Removal and Installation ..216
TRUNK LID HINGE ..................................................216
TRUNK LID HINGE : Exploded View ....................217
TRUNK LID HINGE : Removal and Installation .....217
TRUNK LID STAY ....................................................217
TRUNK LID STAY : Exploded View ......................218
TRUNK LID STAY : Removal and Installation .......218
TRUNK LID WEATHER-STRIP ...............................219
TRUNK LID WEATHER-STRIP : Exploded View ..219
TRUNK LID WEATHER-STRIP : Removal and In-
stallation ................................................................
219
HOOD LOCK ...................................................220
Exploded View .......................................................220
Removal and Installation .......................................220
Inspection ..............................................................221
FRONT DOOR LOCK .....................................222
DOOR LOCK ............................................................222
DOOR LOCK : Exploded View ..............................222
DOOR LOCK : Removal and Installation ...............222
INSIDE HANDLE ......................................................223
INSIDE HANDLE : Exploded View ........................223
INSIDE HANDLE : Removal and Installation .........223
OUTSIDE HANDLE ..................................................223
OUTSIDE HANDLE : Exploded View ....................224
OUTSIDE HANDLE : Removal and Installation .....224
REAR DOOR LOCK ........................................227
DOOR LOCK ............................................................227
DOOR LOCK : Exploded View ..............................227
DOOR LOCK : Removal and Installation ...............227
INSIDE HANDLE ......................................................227
INSIDE HANDLE : Exploded View ........................228
INSIDE HANDLE : Removal and Installation .........228
OUTSIDE HANDLE ..................................................228
OUTSIDE HANDLE : Exploded View ....................229
OUTSIDE HANDLE : Removal and Installation .....229
TRUNK LID LOCK ..........................................231
Exploded View .......................................................231
Removal and Installation .......................................231
FUEL FILLER LID OPENER ...........................232
Exploded View .......................................................232
Removal and Installation .......................................232
DOOR SWITCH ...............................................234
Exploded View .......................................................234
Removal and Installation .......................................234

SQUEAK AND RATTLE TROUBLE DIAGNOSES
DLK-185
< SYMPTOM DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
SEATS
When isolating seat noise it is important to note the position the seat is in and the load placed on the seat
when the noise occurs. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1. Headrest rods and holder
2. A squeak between the seat pad cushion and frame
3. Rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1. Any component mounted to the engine wall
2. Components that pass through the engine wall
3. Engine wall mounts and connectors
4. Loose radiator mounting pins
5. Hood bumpers out of adjustment
6. Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.

HOOD
DLK-191
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
ON-VEHICLE REPAIR
HOOD
HOOD ASSEMBLY
HOOD ASSEMBLY : Exploded ViewINFOID:0000000003813383
REMOVAL
ADJUSTMENT
1. Hood insulator 2. Hood hinge (RH/LH) 3. Hood seal (front) (RH/LH)
4. Radiator core seal 5. Grommet 6. Hood support rod
7. Clamp 8. Hood assembly 9. Hood bumper rubber (lower) (RH/
LH)
10. Hood bumper rubber (side) (RH/LH)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2380ZZ

DLK-192
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
HOOD
HOOD ASSEMBLY : Removal and Installation
INFOID:0000000003813384
CAUTION:
Operate with two workers, because of its heavy weight.
REMOVAL
1. Remove hood insulator.
2. Remove washer nozzle and washer tube. Refer to WW-102, "
Removal and Installation".
3. Support hood assembly with a proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the hood open when removing the hood
stay.
4. Remove hood hinge mounting nuts on the hood to remove the hood assembly.
5. Remove the following parts after removing the hood assembly.
 Radiator core seal
 Hood bumper rubber (lower, side)
 Hood seal (front)
1. Hood assembly 2. Hood bumper rubber 3. Hood lock assembly
4. Hood hinge 5. Front bumper fascia 6. Front combination lamp
7. Front fender
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2391GB

DLK-194
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
HOOD
HOOD HINGE : Exploded View
INFOID:0000000003819555
HOOD HINGE : Removal and InstallationINFOID:0000000003813387
REMOVAL
1. Remove hood assembly. Refer to DLK-192, "HOOD ASSEMBLY : Removal and Installation".
2. Remove front fender. Refer to DLK-199, "
Removal and Installation".
3. Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
 After installation, apply touch-up paint (the body color) onto the head of the hinge mounting bolts
and nuts.
 After installation, perform hood fitting adjustment. Refer to DLK-193, "
HOOD ASSEMBLY : Adjust-
ment".
HOOD SUPPORT ROD
1. Hood insulator 2. Hood hinge (RH/LH) 3. Hood seal (front) (RH/LH)
4. Radiator core seal 5. Grommet 6. Hood support rod
7. Clamp 8. Hood assembly 9. Hood bumper rubber (lower) (RH/
LH)
10. Hood bumper rubber (side) (RH/LH)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2380ZZ

HOOD
DLK-195
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
HOOD SUPPORT ROD : Exploded ViewINFOID:0000000003819556
HOOD SUPPORT ROD : Removal and InstallationINFOID:0000000003813389
REMOVAL
1. Support hood assembly with a proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the hood open when removing the hood
support rod.
2. Pull hood support rod from grommet and remove.
INSTALLATION
Install in the reverse order of removal.
1. Hood insulator 2. Hood hinge (RH/LH) 3. Hood seal (front) (RH/LH)
4. Radiator core seal 5. Grommet 6. Hood support rod
7. Clamp 8. Hood assembly 9. Hood bumper rubber (lower) (RH/
LH)
10. Hood bumper rubber (side) (RH/LH)
Refer to GI-4, "
Components" for symbols in the figure.
JMKIA2380ZZ

DLK-196
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Exploded ViewINFOID:0000000003795070
Removal and InstallationINFOID:0000000003795071
REMOVAL
1. Use refrigerant collecting equipment to discharge the refrigerant. Refer to HA-24, "Collection and
Charge".
2. Remove front under cover. Refer to EXT-28, "
Removal and Installation".
3. Drain engine coolant from radiator. Refer to CO-8, "
Draining".
4. Remove front bumper fascia, energy absorber and bumper reinforcement. Refer to EXT-12, "
Removal
and Installation".
5. Remove mounting clips and remove air duct cover.
6. Remove hood lock opener and hood lock. Refer to DLK-220, "
Removal and Installation".
7. Disconnect connector of horn (HIGH/LOW), and then remove horn (HIGH/LOW). Refer to HRN-6,
"Removal and Installation".
8. Disconnect connector of gas sensor, and then remove gas sensor (with intelligent air conditioner system).
Refer to VTL-82, "
WITH INTELLIGENT AIR CONDITIONER SYSTEM : Removal and Installation".
9. Remove bumper retainer assembly. Refer to EXT-12, "
Removal and Installation".
10. Remove air guide (RH/LH).
11. Remove front combination lamp (RH/LH). Refer to EXL-181, "
Removal and Installation" (XENON TYPE)
or EXL-343, "
Removal and Installation" (HALOGEN TYPE).
12. Disconnect connector of ambient sensor. Refer to VTL-24, "
Removal and Installation" (WITHOUT 7 INCH
DISPLAY) or VTL-81, "
Removal and Installation" (WITH 7 INCH DISPLAY).
1. Radiator upper hose bracket 2. Hood switch bracket 3. Air duct cover
4. Air guide (RH/LH) 5. Radiator core support
: Pawl
JMKIA2382ZZ

RADIATOR CORE SUPPORT
DLK-197
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
13. Disconnect connector of refrigerant pressure sensor. Refer to HA-50, "Exploded View".
14. Remove mounting bolt, and then remove engine coolant reservoir tank. Refer to CO-13, "
Exploded View".
15. Remove mounting bolts, and then disconnect condenser pipe assembly. Refer to HA-48, "
Exploded
View".
16. Remove condenser. Refer to HA-46, "
Removal and Installation".
17. Remove mounting nut of radiator upper hose from radiator core support, and then remove radiator upper
hose and hood switch bracket. Refer to CO-25, "
Exploded View".
18. Disconnect radiator upper hose from radiator pipe (upper). Refer to CO-25, "
Exploded View".
19. Disconnect radiator lower hose (3). Refer to CO-25, "
Exploded View".
20. Disconnect CVT fluid cooler hose on radiator side. Refer to TM-165, "
Exploded View" (CVT: RE0F09B) or
TM-329, "
Exploded View" (CVT: RE0F10A).
21. Remove power steering oil cooler pipe from radiator core sup-
port at point shown by arrows in the figure.
22. Disconnect connectors of the following parts.
 Cooling fan (RH/LH). Refer to CO-16, "
Exploded View".
 Crash zone sensor. Refer to SR-18, "
Removal and Installation".
23. Remove radiator upper clip. Refer to CO-13, "
Exploded View".
24. Remove all harness clips from radiator core support.
CAUTION:
Never damage radiator.
25. Support hood assembly with a proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the hood open when removing the hood
stay.
26. Remove hood support rod. Refer to DLK-195, "
HOOD SUPPORT ROD : Removal and Installation".
27. Remove mounting bolts, and then remove radiator core support.
CAUTION:
 Operate with two workers, because of its heavy weight.
 Never damage power steering oil cooler pipe.
28. Remove the following parts after removing radiator core support.
 Radiator lower hose, radiator upper hose, radiator pipe. Refer to CO-25, "
Exploded View".
 Radiator. Refer to CO-13, "
Exploded View".
 Cooling fan (RH/LH). Refer to CO-16, "
Exploded View".
 Crash zone sensor. Refer to SR-18, "
Exploded View".
 Power steering oil cooler pipe clip. Refer to ST-34, "
Exploded View".
INSTALLATION
Install in the reverse order of removal.
JMKIA2395ZZ
: harness clip
JMKIA2396ZZ

DLK-198
< ON-VEHICLE REPAIR >[WITH INTELLIGENT KEY SYSTEM]
RADIATOR CORE SUPPORT
CAUTION:
 After installation, inspection and replenish the following.
- Engine coolant. Refer to CO-8, "
Inspection", CO-9, "Refilling".
- CVT fluid. Refer to TM-142, "
Inspection", TM-143, "Changing" (CVT: RE0F09B) or TM-304, "Inspec-
tion", TM-305, "Changing" (CVT: RE0F10A).
 After installation, adjust the following parts.
- Front combination lamp. EXL-174, "
Aiming Adjustment Procedure (Low Beam)", EXL-175, "Aiming
Adjustment Procedure (High Beam)" (XENON TYPE) or EXL-337, "Aiming Adjustment Procedure
(Low Beam)", EXL-338, "Aiming Adjustment Procedure (High Beam)" (HALOGEN TYPE).