radio NISSAN TEANA 2008 Owner's Manual

AV-406
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
MULTI AV SYSTEM
MULTIFUNCTION SWITCH Operation panel is equipped with the centralized switch where camera, audio,
DVD and AUX input operations are integrated.
 The multifunction switch is connected to the preset switch by wiring harness,
and it transmits the operation signal to the preset switch.
PRESET SWITCH Operation panel is equipped with the centralized switch where audio and air
conditioner operations are integrated.
 The preset switch is connected via AV communication, and it transmits the op-
eration signals of the preset switch and multifunction switch.
 The disk ejection operating signal is performed by wiring harness.
CAMERA CONTROL UNIT Camera image signal is input from rear view camera. Camera image signal
output to AV control unit.
 Power supply is transmitted to rear view camera.
 AV control unit recognizes the presence of camera system with camera con-
nection recognition signal.
 Camera control unit is connected via AV communication.
REAR VIEW CAMERA The image of vehicle rear view is transmitted to camera control unit.
 It receives the power supply from the camera control unit and operates.
STEERING ANGLE SENSOR Sensor signal (steering angle) is transmitted to camera control unit.
MICROPHONE Used for hands-free phone operation.
 Mic. signal is transmitted to NAVI control unit
 Power (Mic. VCC) is supplied from NAVI control unit.
STEERING SWITCH Enables audio operations, etc.
 Steering switch signal (operation signal) is output to AV control unit.
DVD PLAYERIt transmits the playback DVD image signal and DVD sound signal to the AV con-
trol unit.
AUXILIARY INPUT JACKS The image signal of the auxiliary input is output via the DVD player and AV con-
trol unit to the display unit.
 The sound signal of the auxiliary input is output via the DVD player and AV con-
trol unit to the BOSE amp.
 The image signal of the auxiliary input is output via the AV control unit to the
display, and it outputs the sound signal to the AV control unit.
REAR CONTROL SWITCH Enables audio operations, etc.
 The rear control switch is connected via AV communication, and it transmits
the operation signals of the rear control switch.
ANTENNA AMP. Radio signal received by glass antenna is amplified and transmitted to AV con-
trol unit.
 Power (antenna amp ON signal) is supplied from AV control unit.
GPS ANTENNA GPS signal is received and transmitted to NAVI control unit.
TEL ANTENNA TEL voice signal is received and transmitted to NAVI control unit.Part name Description

AV
AUDIO SYSTEM
AV-407
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
AUDIO SYSTEM
System DiagramINFOID:0000000003765831
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
System DescriptionINFOID:0000000003765832
The audio system is equipped with following function. Each function can be operated with the multifunction
switch, preset switch, rear control switch or steering switch. It indicates the operation status of AUDIO to the
display unit.
FUNCTION DESCRIPTION
Operating Signal
Operation of the audio system can be performed via the multifunction switch, preset switch, rear control switch
or steering switch.
 Operating signal is transmitted to AV control unit via AV communication when it is operated by multifunction
switch, preset switch or rear control switch. The CD ejection operating signal is performed by hard-wire.
 Operating signal is transmitted to AV control unit with steering switch signal when it is operated by steering
switch.
Screen Display
 The display switching of the screen is performed by the communication signal between the display unit and
the AV control unit.
 The image signal to display operating condition is performed by RGB image signal, RGB area signal and
RGB image synchronizing signal.
AM/FM Radio Mode
 AM/FM radio tuner is built into AV control unit.
 AM/FM radio wave is received by glass antenna, next it is amplified by antenna amp., and finally it is input to
AV control unit. The FM sub antenna is installed on the rear window glass and the AV control unit is
received.
 Sound signal is input to BOSE amp. and BOSE amp. outputs to woofer and each speaker for AV control unit.
CD Mode
 CD function is built into AV control unit.
 AV control unit outputs sound signal to BOSE amp. and BOSE amp. outputs to woofer and each speaker
when CD is inserted to AV control unit.
JSNIA1310GB
Function
AM/FM radio
CD

AV
AUDIO SYSTEM
AV-409
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003765834
13. Camera control unit 14. TEL antenna 15. Rear squawker RH
16. Antenna amp. 17. GPS antenna 18. Rear door speaker RH
19. Front door speaker RH 20. Steering angle sensor 21. Steering switch
22. AV control unit 23. Auxiliary input jacks 24. Preset switch
25. DVD player 26. Multifunction switch 27. Display unit
28. Microphone
A. Trunk room upper LH B. Trunk room upper RH C. Trunk room side RH
D. Within rear pillar finisher RH E. Within rear pillar finisher RH F. Within rear parcel shelf finisher
G. Spiral cable part H. In center console I. In grove box
Part name Description
AV CONTROL UNIT The AM/FM receiving function and the CD playing function are equipped.
 Sound signal is transmitted to BOSE amp.
DISPLAY UNIT Display image is controlled by the serial communication from AV control unit.
 RGB image signal (audio operation condition) is input from AV control unit.
BOSE AMP.Inputs sound signal from AV control unit, and outputs sound signal to woofer and
each speaker.
WOOFER Outputs sound signal from BOSE amp.
 Outputs low frequency sound.
FRONT SPEAKER Outputs sound signal from BOSE amp.
 Outputs sound (mid and low range).
REAR SPEAKER Outputs sound signal from BOSE amp.
 Outputs sound (mid and low range).
FRONT SQUAWKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).
REAR SQUAWKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).
CENTER SPEAKER Outputs sound signal from BOSE amp.
 Outputs sound (high and mid range).
MULTIFUNCTION SWITCH Each audio operation can be operated.
 The multifunction switch is connected to the preset switch by wiring harness,
and it transmits the operation signal to the preset switch.
PRESET SWITCH Each audio operation can be operated.
 The preset switch is connected via AV communication, and it transmits the op-
eration signals of the preset switch and multifunction switch.
 The disk ejection operating signal is performed by hard-wire.
STEERING SWITCH Each audio operation can be operated.
 Steering switch signal (operation signal) is output to AV control unit.
REAR CONTROL SWITCH Each audio operation can be operated.
 The rear control switch is connected via AV communication, and it transmits
the operation signals of the rear control switch.
ANTENNA AMP. Radio signal received by glass antenna is amplified and transmitted to AV con-
trol unit.
 Power (antenna amp. ON signal) is supplied from AV control unit.

AV-412
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
NAVIGATION SYSTEM
 Map-matching does not function correctly when a road on which
the vehicle is driving is new and not recorded in the map DVD-
ROM, or when road pattern stored in the map data and the actual
road pattern are different due to repair.
The map-matching function may find another road and position the
vehicle mark on it when driving on a road not present in the map.
Then, the vehicle mark may change to it when the correct road is
detected.
 Effective range for comparing the vehicle position and travel direc-
tion calculated by the distance and direction with the road data
read from the map DVD-ROM is limited. Therefore, correction by
map-matching is not possible when there is an excessive gap
between current vehicle position and the position on the map.
GPS (GLOBAL POSITIONING SYSTEM)
GPS (Global Positioning System) was developed for and is con-
trolled by the US Department of Defense. The system utilizes GPS
satellites (NAVSTAR), sending out radio waves while flying on an
orbit around the earth at an altitude of approximately 21,000 km
(13,100miles).
The GPS receiver calculates the vehicle's position in three dimen-
sions (latitude/longitude/altitude) according to the time lag of the
radio waves received from four or more GPS satellites (three-dimen-
sional positioning). The GPS receiver calculates the vehicle's posi-
tion in two dimensions (latitude/longitude), utilizing the altitude data
calculated previously with radio waves from four or more GPS satel-
lites (two-dimensional positioning) if radio waves were received only
from three GPS satellites.
Position correction by GPS is not available while the vehicle is stopped.
Accuracy of GPS will deteriorate under the following conditions:
 In two-dimensional positioning, GPS accuracy will deteriorate when altitude of the vehicle position changes.
 The accuracy can be even lower depending on the arrangement of the GPS satellites utilized for the posi-
tioning.
 Position detection is not possible when vehicle is in an area where radio waves from the GPS satellite do not
reach, such as in a tunnel, parking lot in a building, and under an elevated highway. Radio waves from the
GPS satellites may not be received when some object is located over the GPS antenna.
NOTE:
 Even a high-precision three dimensional positioning, the detection result has an error about 10 m (30ft).
 Because the signals of GPS satellite is controlled by the Tracking and Control Center in the United States,
the accuracy may be degraded lower intentionally or the radio waves may stop.
SKIA0613E
SEL526V

AV
MULTI AV SYSTEM SYMPTOMS
AV-643
< SYMPTOM DIAGNOSIS >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
RELATED TO STEERING SWITCH
RELATED TO DVD
RELATED TO AUXILIARY INPUT
NOTE:
Check that there is no malfunction of AUX equipment main body before performing a diagnosis.
Symptoms Check items Possible malfunction location / Action to take
The CD cannot be removed. —Disk eject signal circuit.
Refer to AV- 4 8 1 , "
Diagnosis Procedure".
Audio sound is not heard.No sound from all speakers. Perform CONSULT-III self-diagnosis.
Refer to AV- 4 3 4 , "
CONSULT-III Function (MULTI AV)"
 BOSE amp. power supply and ground circuits malfunc-
tion. Refer to AV- 4 6 6 , "
BOSE AMP. : Diagnosis Proce-
dure".
 No sound from all speakers.
 It dose not change to “DVD” mode.
Perform CONSULT-III self-diagnosis.
Refer to AV- 4 3 4 , "
CONSULT-III Function (MULTI AV)"Sound is not heard only from the specific
places.
AM/FM radio is not received. Other audio sounds are normal. Antenna amp. ON signal circuit.
Symptoms Probable malfunction location
None of the steering switch operations work.Steering switch signal GND circuit malfunction.
Refer to AV- 4 9 3 , "
Diagnosis Procedure".
Only specified switch (1) cannot be operated.Steering switch malfunction.
Replace steering switch.
Steering switch's “SOURCE”, “MENU UP”, “MENU DOWN”,
“ ”, “ENTER” switches do not work.Steering switch signal A circuit malfunction.
Refer to AV- 4 8 9 , "
Diagnosis Procedure".
Steering switch's “ ”, “VOL UP”, “VOL DOWN”, “ ”
switches do not work.Steering switch signal B circuit malfunction.
Refer to AV- 4 9 1 , "
Diagnosis Procedure".
Symptoms Check items Probable malfunction location
DVD image is not displayed Displayed in black and nothing displayed. Composite image signal circuit malfunc-
tion between AV control unit and display
unit.
Refer to AV- 4 8 6 , "
Diagnosis Procedure"
 RGB area synchronizing (YS) signal cir-
cuit malfunction between AV control unit
and display unit.
Refer to AV- 4 7 3 , "
Diagnosis Procedure"
 Horizontal synchronizing (HP) signal cir-
cuit malfunction between AV control unit
and display unit.
Refer to AV- 4 7 4 , "
Diagnosis Procedure".
 Vertical synchronizing (VP) signal circuit
malfunction between AV control unit and
display unit.
Refer to AV- 4 7 5 , "
Diagnosis Procedure".
It dose not change to “DVD” mode.LED lump of DVD player is not turned on.DVD player power supply and ground cir-
cuits malfunction.
Refer to AV- 4 6 8 , "
DVD PLAYER : Diagno-
sis Procedure".
LED lump of DVD player is not turned on.Perform CONSULT-III self-diagnosis. Refer
to AV- 4 3 4 , "
CONSULT-III Function (MULTI
AV )"

AV
ANTENNA FEEDER (RADIO)
AV-673
< ON-VEHICLE REPAIR >[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ANTENNA FEEDER (RADIO)
Harness LayoutINFOID:0000000003766037
JPNIA1054GB

PEDAL VIBRATION OR ABS OPERATION SOUND OCCURS
BRC-53
< SYMPTOM DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
PEDAL VIBRATION OR ABS OPERATION SOUND OCCURS
Diagnosis ProcedureINFOID:0000000003766856
CAUTION:
Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly
depressed (just place a foot on it). However, this is normal.
 When shifting gears
 When driving on slippery road
 During cornering at high speed
 When passing over bumps or grooves [at approximately 50 mm (1.97 in) or more]
 When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher]
1.SYMPTOM CHECK 1
Check that there are pedal vibrations when the engine is started.
Do vibrations occur?
YES >> GO TO 2.
NO >> Inspect the brake pedal.
2.SYMPTOM CHECK 2
Check that there are ABS operation noises when the engine is started.
Do the operation noises occur?
YES >> GO TO 3.
NO >> Perform self-diagnosis.
3.SYMPTOM CHECK 3
Check symptoms when electrical component (headlamps, etc.) switches are operated.
Do symptoms occur?
YES >> Check if there is a radio, antenna, antenna lead wire, or wiring close to the control unit. If there is,
move it farther away.
NO >> Normal

BRC-56
< PRECAUTION >[ABS]
PRECAUTIONS
Precaution for Brake Control
INFOID:0000000003766861
 When starting engine or when starting vehicle just after starting engine, brake pedal may vibrate or motor
operating noise may be heard from engine compartment. This is normal condition.
 When an error is indicated by ABS or another warning lamp, collect all necessary information from customer
(what symptoms are present under what conditions) and check for estimate causes before starting diagnos-
tic servicing. Besides electrical system inspection, check brake booster operation, brake fluid level, and oil
leaks.
 If tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.
 ABS might be out of order or malfunctions by putting a radio (wiring inclusive), an antenna and a lead-in wire
near the control unit.
 If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits, and improper wiring.
Precautions for Harness RepairINFOID:0000000003859437
COMMUNICATION LINE
 Solder the repaired area and wrap tape around the soldered area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
 Bypass connection is never allowed at the repaired area.
NOTE:
Bypass connection may cause communication error as spliced
wires that are separate from the main line or twisted lines lose
noise immunity.
 Replace the applicable harness as an assembly if error is detected
on the shield lines of communication line.
SKIB8766E
SKIB8767E

BRC-146
< SYMPTOM DIAGNOSIS >[VDC/TCS/ABS]
PEDAL VIBRATION OR ABS OPERATION SOUND OCCURS
PEDAL VIBRATION OR ABS OPERATION SOUND OCCURS
Diagnosis ProcedureINFOID:0000000003767027
CAUTION:
Under the following conditions, ABS is activated and vibration is felt when brake pedal is lightly
depressed (just place a foot on it). However, this is normal.
 When shifting gears
 When driving on slippery road
 During cornering at high speed
 When passing over bumps or grooves [at approximately 50 mm (1.97 in) or more]
 When pulling away just after starting engine [at approximately 10 km/h (6 MPH) or higher]
1.SYMPTOM CHECK 1
Check that there are pedal vibrations when the engine is started.
Do vibrations occur?
YES >> GO TO 2.
NO >> Inspect the brake pedal.
2.SYMPTOM CHECK 2
Check that there are ABS operation noises when the engine is started.
Do the operation noises occur?
YES >> GO TO 3.
NO >> Perform self-diagnosis.
3.SYMPTOM CHECK 3
Check symptoms when electrical component (headlamps, etc.) switches are operated.
Do symptoms occur?
YES >> Check if there is a radio, antenna, antenna lead wire, or wiring close to the control unit. If there is,
move it farther away.
NO >> Normal

BRC-150
< PRECAUTION >[VDC/TCS/ABS]
PRECAUTIONS
Precaution for Brake Control
INFOID:0000000003767032
 When starting engine or when starting vehicle just after starting engine, brake pedal may vibrate or motor
operating noise may be heard from engine compartment. This is normal condition.
 When an error is indicated by ABS or another warning lamp, collect all necessary information from customer
(what symptoms are present under what conditions) and check for estimate causes before starting diagnos-
tic servicing. Besides electrical system inspection, check brake booster operation, brake fluid level, and oil
leaks.
 If tire size and type are used in an improper combination, or brake pads are not Genuine NISSAN parts,
stopping distance or steering stability may deteriorate.
 ABS might be out of order or malfunctions by putting a radio (wiring inclusive), an antenna and a lead-in wire
near the control unit.
 If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits, and improper wiring.
 VDC system may not operate normally or a VDC OFF indicator lamp or SLIP indicator lamp may light.
- When replacing the following parts with parts other than genuine parts or making modifications: Suspension
related parts (shock absorber, spring, bushing, etc.), tires, wheels (other than specified sizes), brake-related
parts (pad, rotor, caliper, etc.), engine-related parts (muffler, ECM, etc.) and body reinforcement-related parts
(roll bar, tower bar, etc.).
- When driving with worn or deteriorated suspension, tires and brake-related parts.
Precautions for Harness RepairINFOID:0000000003843440
COMMUNICATION LINE
 Solder the repaired area and wrap tape around the soldered area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
 Bypass connection is never allowed at the repaired area.
NOTE:
Bypass connection may cause communication error as spliced
wires that are separate from the main line or twisted lines lose
noise immunity.
 Replace the applicable harness as an assembly if error is detected
on the shield lines of communication line.
SKIB8766E
SKIB8767E