reset NISSAN TEANA 2008 Owner's Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TEANA, Model: NISSAN TEANA 2008Pages: 5121, PDF Size: 69.03 MB
Page 339 of 5121
![NISSAN TEANA 2008 Owners Guide AV
AUDIO SYSTEM
AV-195
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003885448
Part name Description
AV CONTROL UNIT The AM/FM NISSAN TEANA 2008 Owners Guide AV
AUDIO SYSTEM
AV-195
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003885448
Part name Description
AV CONTROL UNIT The AM/FM](/img/5/57391/w960_57391-338.png)
AV
AUDIO SYSTEM
AV-195
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
Component DescriptionINFOID:0000000003885448
Part name Description
AV CONTROL UNIT The AM/FM receiving function and the CD playing function are equipped.
Sound signal is transmitted to BOSE amp.
DISPLAY UNIT Display image is controlled by the serial communication from AV control unit.
RGB image signal (audio operation condition) is input from AV control unit.
BOSE AMP.Inputs sound signal from AV control unit, and outputs sound signal to woofer and
each speaker.
WOOFER Outputs sound signal from BOSE amp.
Outputs low frequency sound.
FRONT SPEAKER Outputs sound signal from BOSE amp.
Outputs sound (mid and low range).
REAR SPEAKER Outputs sound signal from BOSE amp.
Outputs sound (mid and low range).
FRONT SQUAWKER Outputs sound signal from BOSE amp.
Outputs sound (high and mid range).
REAR SQUAWKER Outputs sound signal from BOSE amp.
Outputs sound (high and mid range).
CENTER SPEAKER Outputs sound signal from BOSE amp.
Outputs sound (high and mid range).
MULTIFUNCTION SWITCH Each audio operation can be operated.
The multifunction switch is connected to the preset switch by wiring harness,
and it transmits the operation signal to the preset switch.
PRESET SWITCH Each audio operation can be operated.
The preset switch is connected via AV communication, and it transmits the op-
eration signals of the preset switch and multifunction switch.
The disk ejection operating signal is performed by hard-wire.
STEERING SWITCH Each audio operation can be operated.
Steering switch signal (operation signal) is output to AV control unit.
REAR CONTROL SWITCH Each audio operation can be operated.
The rear control switch is connected via AV communication, and it transmits
the operation signals of the rear control switch.
ANTENNA AMP. Radio signal received by glass antenna is amplified and transmitted to AV con-
trol unit.
Power (antenna amp. ON signal) is supplied from AV control unit.
Page 342 of 5121
![NISSAN TEANA 2008 Owners Guide AV-198
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
REAR VIEW MONITOR SYSTEM
Component Parts Location
INFOID:0000000003791258
1. Front squawker RH 2. Center speaker 3. Front squawker LH
4. Fr NISSAN TEANA 2008 Owners Guide AV-198
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
REAR VIEW MONITOR SYSTEM
Component Parts Location
INFOID:0000000003791258
1. Front squawker RH 2. Center speaker 3. Front squawker LH
4. Fr](/img/5/57391/w960_57391-341.png)
AV-198
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
REAR VIEW MONITOR SYSTEM
Component Parts Location
INFOID:0000000003791258
1. Front squawker RH 2. Center speaker 3. Front squawker LH
4. Front door speaker LH 5. Rear door speaker LH 6. Rear control switch
7. Rear squawker LH 8. Woofer LH 9. BOSE amp.
10. Rear view camera 11. Woofer RH 12. Camera control unit
13. Rear squawker RH 14. Antenna amp. 15. Rear door speaker RH
16. Front door speaker RH 17. Steering angle sensor 18. Steering switch
19. AV control unit 20. Auxiliary input jacks 21. Preset switch
22. DVD player 23. Multifunction switch 24. Display unit
A. Trunk room upper RH B. Trunk room side RH C. Within rear pillar finisher RH
D. Spiral cable part E. In center console F. In grove box
JPNIA1058ZZ
Page 344 of 5121
![NISSAN TEANA 2008 Owners Guide AV-200
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Diagnosis DescriptionINFOID:0000000003765657
MULTIFUNCTION SWITCH AND NISSAN TEANA 2008 Owners Guide AV-200
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Diagnosis DescriptionINFOID:0000000003765657
MULTIFUNCTION SWITCH AND](/img/5/57391/w960_57391-343.png)
AV-200
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Diagnosis DescriptionINFOID:0000000003765657
MULTIFUNCTION SWITCH AND PRESET SWITCH SELF-DIAGNOSIS FUNCTION
The ON/OFF operation (continuity) of each switch in the multifunction switch and preset switch can be
checked.
Self-diagnosis Mode
Press the “BACK” switch and the “UP” switch of the 4-direction
switches within 10 seconds after turning the ignition switch from
OFF to ACC and hold them for 3 seconds or more. Then the
buzzer sounds, all indicators of the preset switch illuminate, and
the self-diagnosis mode starts.
The continuity of each switch at the ON position can be checked
by pressing the switch. The buzzer sounds if the switch is normal.
NOTE:
The hazard switch and disk eject switch cannot be checked.
Finishing Self-diagnosis Mode
Self-diagnosis mode is canceled when turning the ignition switch OFF.
MULTI AV SYSTEM ON BOARD DIAGNOSIS FUNCTION
The AV control unit diagnosis function starts up with multifunction switch operation and the AV control unit
performs a diagnosis for each unit in the system during the on board diagnosis.
Perform a CONSULT-III diagnosis if the on board diagnosis does not start, e.g., the screen does not display
anything, the multifunction switch does not function, etc.
ON BOARD DIAGNOSIS
Description
The trouble diagnosis function has a self-diagnosis mode for conducting trouble diagnosis automatically and
a confirmation/adjustment mode for operating manually.
Self-diagnosis mode performs the AV control unit diagnosis and the connection diagnosis between each of
the units that make up the system, and it indicates the results to the display.
The confirmation/adjustment mode allows the technician to check, modify or adjust the vehicle signals and
set values, as well as to monitor the system error records and system communication status. The check,
modify or adjust actions generally require human intervention and judgment (the system cannot make judg-
ment automatically).
On Board Diagnosis Item
JSNIA1284GB
Mode Description
Self Diagnosis AV control unit diagnosis.
Diagnoses the connections across system components.
Page 350 of 5121
![NISSAN TEANA 2008 Owners Guide AV-206
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Select “SPEAKER DIAGNOSIS” to display the Speaker Diagnosis
screen. Press “START and NEXT” to ge NISSAN TEANA 2008 Owners Guide AV-206
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Select “SPEAKER DIAGNOSIS” to display the Speaker Diagnosis
screen. Press “START and NEXT” to ge](/img/5/57391/w960_57391-349.png)
AV-206
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Select “SPEAKER DIAGNOSIS” to display the Speaker Diagnosis
screen. Press “START and NEXT” to generate a test tone in a
speaker. Press “Start” to generate a test tone in the next speaker.
Press “End” to stop the test tones.
NOTE:
The frequency of test tone emitted from each speaker is as follows.
Climate Control
On-board self-diagnosis is not supported. Only CONSULT-III is supported.
Refer to HAC-156, "
WITHOUT INTELLIGENT AIR CONDITIONER SYSTEM : CONSULT-III Function" for
details.
Camera Cont.
Refer to AV-196, "System Description".
Error History
The self-diagnosis results are judged depending on whether any error occurs from when “Self-diagnosis” is
selected until the self-diagnosis results are displayed.
However, the diagnosis results are judged normal if an error has occurred before the ignition switch is turned
ON and then no error has occurred until the self-diagnosis start. Check the “Error Record” to detect any error
that may have occurred before the self-diagnosis start because of this situation.
The error record displays the time and place of the most recent occurrence of that error. However, take note of
the following points.
Place of the error occurrence is represented by the position of the current location mark at the time an error
occurred. If current location mark has deviated from the correct position, then the place of the error occur-
rence cannot be located correctly.
The frequency of occurrence is displayed in a count up manner. The actual count up method differs depend-
ing on the error item.
Count up method A
The counter resets to 0 if an error occurs when IGN switch is turned ON. The counter increases by 1 if the
condition is normal at a next IGN ON cycle.
The counter upper limit is 39. Any counts exceeding 39 are ignored.“ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.
Count up method B
The counter increases by 1 if an error occurs when IGN switch is ON. The counter will not decrease even if
the condition is normal at the next IGN ON cycle.
The counter upper limit is 50. Any counts exceeding 50 are ignored. “ The counter can be reset (no error
record display) with the “Delete log” switch or CONSULT-III.Squawker : 3 kHz
Front speaker : 300 Hz
Rear speaker : 1 kHz
JSNIA0150GB
Display type of occur-
rence frequencyError history display item
Count up method A CAN communication line, control unit (CAN), AV communication line, control unit (AV communication)
Count up method B Other than the above
Page 354 of 5121
![NISSAN TEANA 2008 Owners Guide AV-210
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Vehicle CAN Diagnosis
CAN communication status and error counter is displayed.
The error counter dis NISSAN TEANA 2008 Owners Guide AV-210
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Vehicle CAN Diagnosis
CAN communication status and error counter is displayed.
The error counter dis](/img/5/57391/w960_57391-353.png)
AV-210
< FUNCTION DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Vehicle CAN Diagnosis
CAN communication status and error counter is displayed.
The error counter displays "OK" if any malfunction was not
detected in the past and displays "0" if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
The error counter is erased if reset.
AV COMM Diagnosis
Displays the communication status between AV control unit (mas-
ter unit) and each unit.
The error counter displays "OK" if any malfunction was not
detected in the past and displays "0" if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
If it resets, the error counter is erased.
AV COMM CIRCUIT
DVD Deck Connection Error
Amplifier Connection Error
Rear view Camera connection ErrorWith rear control switch
When either one of the following items is
detected:
malfunction is detected in AV communi-
cation circuits between rear control
switch and camera control unit.
malfunction is detected in AV communi-
cation circuits between camera control
unit and NAVI control unit. AV communication circuits between mul-
tifunction switch and rear control switch.
AV communication circuits between rear
control switch and camera control unit.
Without rear control switch
When either one of the following items is
detected:
malfunction is detected in AV communi-
cation circuits between multifunction
switch and camera control unit.
malfunction is detected in AV communi-
cation circuits between camera control
unit and NAVI control unit.AV communication circuits between multi-
function switch and camera control unit.
AV COMM CIRCUIT
Switches Connection Error
DVD Deck Connection Error
Amplifier Connection Error
Rear view Camera connection ErrorWhen either one of the following items is
detected:
AV communication circuits between AV
control unit and multifunction switch are
malfunctioning.
AV communication signal between AV
control unit and multifunction switch is
malfunctioning.AV communication circuits between AV
control unit and multifunction switch. Error item Description Possible malfunction factor/Action to take
Items Display (Current)Malfunction counter
(Past)
Tx (HVAC) OK / UNKWN OK / 0 – 39
Rx (ECM) OK / UNKWN OK / 0 – 39
Rx (Cluster) OK / UNKWN OK / 0 – 39
Rx (BCM) OK / UNKWN OK / 0 – 39
Rx (HVAC) OK / UNKWN OK / 0 – 39
Rx (USM) OK / UNKWN OK / 0 – 39
JSNIA1287GB
ItemsStatus
(Current)Counter
(Past)
C Tx(ITM–SW) OK / UNKWN OK / 0 – 39
C Rx(PrimarySW–ITM) OK / UNKWN OK / 0 – 39
JSNIA1288GB
Page 393 of 5121
![NISSAN TEANA 2008 Owners Guide AV
DISK EJECT SIGNAL CIRCUIT
AV-249
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
DISK EJECT SIGNAL CIRCUIT
DescriptionINFOID:0000000003765719
The eject signal is NISSAN TEANA 2008 Owners Guide AV
DISK EJECT SIGNAL CIRCUIT
AV-249
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
DISK EJECT SIGNAL CIRCUIT
DescriptionINFOID:0000000003765719
The eject signal is](/img/5/57391/w960_57391-392.png)
AV
DISK EJECT SIGNAL CIRCUIT
AV-249
< COMPONENT DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
DISK EJECT SIGNAL CIRCUIT
DescriptionINFOID:0000000003765719
The eject signal is output to AV control unit when the eject switch of multifunction switch is pressed.
Diagnosis ProcedureINFOID:0000000003901193
1.CHECK CONTINUITY DISK EJECT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect multifunction switch connector and AV control unit connector.
3. Check continuity between multifunction switch harness connector and AV control unit harness connector.
4. Check continuity between multifunction switch harness connector and ground.
Is inspection result normal?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK AV CONTROL UNIT VOLTAGE
1. Connect multifunction switch connector and AV control unit connector.
2. Turn ignition switch ON.
3. Check voltage between AV control unit harness connector and ground.
Is inspection result normal?
YES >> Replace preset switch.
NO >> Replace AV control unit.
Multifunction switch AV control unit
Continuity
Connector Terminal Connector Terminal
M125 14 M131 103 Existed
Multifunction switch
GroundContinuity
Connector Terminal
M125 14 Not existed
(+)
(−) Condition Reference value AV c o n t r o l u n i t
Connector Terminal
M131 103 GroundPressing the eject switch. 0 V
Except for above. 3.3 V
Page 428 of 5121
![NISSAN TEANA 2008 Owners Guide AV-284
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
AV CONTROL UNIT
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
DTC IndexINFO NISSAN TEANA 2008 Owners Guide AV-284
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
AV CONTROL UNIT
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
DTC IndexINFO](/img/5/57391/w960_57391-427.png)
AV-284
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
AV CONTROL UNIT
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
DTC IndexINFOID:0000000003765759
SELF-DIAGNOSIS RESULTS DISPLAY ITEM
JCNWM0934GB
Page 451 of 5121
![NISSAN TEANA 2008 Owners Guide AV
DISPLAY UNIT
AV-307
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SW NISSAN TEANA 2008 Owners Guide AV
DISPLAY UNIT
AV-307
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SW](/img/5/57391/w960_57391-450.png)
AV
DISPLAY UNIT
AV-307
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
JCNWM0934GB
Page 473 of 5121
![NISSAN TEANA 2008 Owners Guide AV
BOSE AMP.
AV-329
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITC NISSAN TEANA 2008 Owners Guide AV
BOSE AMP.
AV-329
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITC](/img/5/57391/w960_57391-472.png)
AV
BOSE AMP.
AV-329
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
JCNWM0934GB
Page 494 of 5121
![NISSAN TEANA 2008 Owners Guide AV-350
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DVD PLAYER
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
JCNWM0934GB NISSAN TEANA 2008 Owners Guide AV-350
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DVD PLAYER
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
JCNWM0934GB](/img/5/57391/w960_57391-493.png)
AV-350
< ECU DIAGNOSIS >[BOSE AUDIO WITHOUT NAVIGATION]
DVD PLAYER
NOTE:
The name MULTIFUNCTION SWITCH indicates the integration of PRESET SWITCH and MULTIFUNCTION
SWITCH virtually.
JCNWM0934GB