steering NISSAN TEANA 2008 Service Manual

RSU-14
< ON-VEHICLE REPAIR >
FRONT LOWER LINK
FRONT LOWER LINK
Exploded ViewINFOID:0000000003811151
Removal and InstallationINFOID:0000000003811152
REMOVAL
1. Remove tire.
2. Remove wheel sensor and sensor harness. Refer to BRC-58, "
REAR WHEEL SENSOR : Exploded View"
(without VDC), BRC-58, "REAR WHEEL SENSOR : Exploded View" (with VDC).
3. Remove rear lower link and coil spring. Refer to RSU-8, "
Exploded View".
4. Remove shock absorber mounting bolt (lower side). Refer to RSU-10, "
Exploded View".
5. Remove front lower link mounting bolts and nuts (axle housing side).
6. Remove front lower link mounting bolts and nuts (rear suspension member side), and then remove front
lower link.
INSTALLATION
Note the following, and install in the reverse order of removal.
 Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
InspectionINFOID:0000000003811153
INSPECTION AFTER REMOVAL
Check front lower link and bushing for any deformation, cracks, or damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to BRC-58, "REAR WHEEL SENSOR :
Exploded View" (without VDC), BRC-152, "REAR WHEEL SENSOR : Exploded View" (with VDC).
2. Check wheel alignment. Refer to RSU-6, "
Inspection".
3. Adjust neutral position of steering angle sensor (with VDC). Refer to BRC-66, "
ADJUSTMENT OF
STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement".
1. Upper seat 2. Coil spring 3. Rubber seat
4. Rear lower link 5. Rear suspension member 6. Radius rod
7. Front lower link
Refer to GI-4, "
Components" for symbols in the figure.
JPEIB0108GB

REAR SUSPENSION ARM
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
MA
B
RSU
N
O
P
 Hook spring balance (A) at cotter pin mounting hole. Confirm
spring balance measurement value is within specifications when
ball stud begins moving.
 If swing torque exceeds the standard value, replace suspension
arm assembly.
Rotating Torque Inspection
 Attach the mounting nut to ball stud. Make sure that rotating torque
is within the specifications with a preload gauge (A) (SST:
ST3127S000).
- If rotating torque exceeds the standard value, replace suspension
arm assembly.
Axial End Play Inspection
 Move tip of ball stud in axial direction to check for looseness.
- If axial end play exceeds the standard value, replace suspension arm assembly.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to BRC-58, "REAR WHEEL SENSOR :
Exploded View" (without VDC), BRC-152, "REAR WHEEL SENSOR : Exploded View" (with VDC).
2. Check wheel alignment. Refer to RSU-6, "
Inspection".
3. Adjust neutral position of steering angle sensor. Refer to BRC-66, "
ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement". Standard
Swing torque : Refer to RSU-20, "
Ball Joint".
JPEIA0005ZZ
Standard
Rotating torque : Refer to RSU-20, "
Ball Joint".
PDIA1258E
Standard
Axial end play : Refer to RSU-20, "
Ball Joint".

REAR SUSPENSION MEMBER
RSU-19
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
MA
B
RSU
N
O
P
 Perform the final tightening of each of parts under unladen conditions, which were removed when removing
rear suspension assembly.
 After final tightening, install auto levelizer control unit (with xenon combination lamp type). Refer to EXL-190,
"Exploded View".
 Never reuse cotter pin.
InspectionINFOID:0000000003811162
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connection. Refer to BRC-58, "REAR WHEEL SENSOR :
Exploded View" (without VDC), BRC-152, "REAR WHEEL SENSOR : Exploded View" (with VDC).
2. Adjust parking brake operation (stroke). PB-2, "
Inspection and Adjustment".
3. Check wheel alignment. Refer to RSU-6, "
Inspection".
4. Adjust neutral position of steering angle sensor. Refer to BRC-66, "
ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement".

SE-3
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P REAR SEAT : Description .......................................
76
REAR SEAT : Diagnosis Procedure .......................76
ONLY SEAT CUSHION HEATER IS OPER-
ATED IN HI MODE OF HEATED SEAT .............
77
FRONT SEAT ............................................................77
FRONT SEAT : Description ....................................77
FRONT SEAT : Diagnosis Procedure .....................77
REAR SEAT ..............................................................77
REAR SEAT : Description .......................................77
REAR SEAT : Diagnosis Procedure .......................77
HEATED SEAT SWITCH INDICATOR DOES
NOT TURN ON ...................................................
78
FRONT SEAT ............................................................78
FRONT SEAT : Diagnosis Procedure .....................78
REAR SEAT ..............................................................78
REAR SEAT : Diagnosis Procedure .......................78
VENTILATION SEAT SWITCH INDICATOR
DOES NOT TURN ON ........................................
79
FRONT SEAT ............................................................79
FRONT SEAT : Diagnosis Procedure .....................79
REAR SEAT ..............................................................79
REAR SEAT : Diagnosis Procedure .......................79
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ...............................................................
80
Work Flow ...............................................................80
Inspection Procedure ..............................................82
Diagnostic Worksheet .............................................84
PRECAUTION ..............................................86
PRECAUTIONS ..................................................86
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
86
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect ...................................
86
Service Notice .........................................................86
Precaution for Work ................................................87
PREPARATION ...........................................88
PREPARATION ..................................................88
Commercial Service Tools .....................................88
ON-VEHICLE REPAIR .................................89
FRONT SEAT .....................................................89
Exploded View ........................................................89
Removal and Installation .........................................92
Disassembly and Assembly ....................................93
REAR SEAT .......................................................98
Exploded View ........................................................98
Removal and Installation .........................................99
Disassembly and Assembly ...................................100
POWER SEAT SWITCH .................................103
Exploded View .......................................................103
Removal and Installation .......................................103
HEATED SEAT SWITCH ................................104
FRONT SEAT ...........................................................104
FRONT SEAT : Exploded View .............................104
FRONT SEAT : Removal and Installation .............104
REAR SEAT .............................................................104
REAR SEAT : Exploded View ...............................105
REAR SEAT : Removal and Installation ................105
VENTILATION SEAT SWITCH .......................106
FRONT SEAT ...........................................................106
FRONT SEAT : Exploded View .............................106
FRONT SEAT : Removal and Installation .............106
REAR SEAT .............................................................106
REAR SEAT : Exploded View ...............................107
REAR SEAT : Removal and Installation ................107
WITHOUT VENTILATION SEAT
FUNCTION DIAGNOSIS ............................
108
POWER SEAT .................................................108
System Description ................................................108
Component Parts Location ....................................108
Component Description .........................................108
HEATED SEAT ...............................................110
System Description ................................................110
Component Parts Location ....................................110
Component Description .........................................110
COMPONENT DIAGNOSIS .......................111
POWER SEAT .................................................111
Wiring Diagram - POWER SEAT FOR DRIVER
SIDE - ....................................................................
111
Wiring Diagram - POWER SEAT FOR PASSEN-
GER SIDE - ...........................................................
114
HEATED SEAT ...............................................118
Wiring Diagram - HEATED SEAT - .......................118
SYMPTOM DIAGNOSIS ............................121
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ............................................................
121
Work Flow ..............................................................121
Inspection Procedure .............................................123
Diagnostic Worksheet ............................................125
PRECAUTION ............................................127
PRECAUTIONS ...............................................127

SE-4
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................
127
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect .................................
127
Service Notice .......................................................127
Precaution for Work ...............................................128
PREPARATION ..........................................129
PREPARATION ...............................................129
Commercial Service Tools ...................................129
ON-VEHICLE REPAIR ...............................130
FRONT SEAT ..................................................130
Exploded View ......................................................130
Removal and Installation .......................................135
Disassembly and Assembly ..................................135
REAR SEAT .....................................................140
Exploded View ......................................................140
Removal and Installation .......................................142
Disassembly and Assembly ..................................142
POWER SEAT SWITCH ...................................144
Exploded View ......................................................144
Removal and Installation .......................................144
HEATED SEAT SWITCH ..................................145
Exploded View ......................................................145
Removal and Installation .......................................145

SE-86
< PRECAUTION >[WITH VENTILATION SEAT]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003940149
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000003885169
NOTE:
 Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
 After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
 Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
Service NoticeINFOID:0000000003809271
 When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent
scratches.
 Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or
damage them.
 Apply sealing compound where necessary when installing parts.
 When applying sealing compound, be careful that the sealing compound does not protrude from parts.

PRECAUTIONS
SE-127
< PRECAUTION >[WITHOUT VENTILATION SEAT]
C
D
E
F
G
H
I
K
L
MA
B
SE
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000003940150
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
 To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
 Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
 Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000003885171
NOTE:
 Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
 After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
 Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
This vehicle is equipped with a push-button ignition switch and a steering lock unit.
If the battery is disconnected or discharged, the steering wheel will lock and cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the procedure
below before starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
Service NoticeINFOID:0000000003840019
 When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent
scratches.
 Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or
damage them.
 Apply sealing compound where necessary when installing parts.
 When applying sealing compound, be careful that the sealing compound does not protrude from parts.

SEC-2
Description ..............................................................34
DTC Logic ...............................................................34
Diagnosis Procedure ..............................................34
P1614 CHAIN OF IMMU-KEY ...........................35
Description ..............................................................35
DTC Logic ...............................................................35
Diagnosis Procedure ..............................................35
P1615 DIFFRENCE OF KEY .............................38
Description ..............................................................38
DTC Logic ...............................................................38
Diagnosis Procedure ..............................................38
B2190 NATS ANTENNA AMP. .........................39
Description ..............................................................39
DTC Logic ...............................................................39
Diagnosis Procedure ..............................................39
B2191 DIFFERENCE OF KEY ..........................42
Description ..............................................................42
DTC Logic ...............................................................42
Diagnosis Procedure ..............................................42
B2192 ID DISCORD, IMMU-ECM ......................43
Description ..............................................................43
DTC Logic ...............................................................43
Diagnosis Procedure ..............................................43
B2193 CHAIN OF ECM-IMMU ...........................45
Description ..............................................................45
DTC Logic ...............................................................45
Diagnosis Procedure ..............................................45
B2013 ID DISCORD, IMMU-STRG ....................46
Description ..............................................................46
DTC Logic ...............................................................46
Diagnosis Procedure ..............................................46
B2014 CHAIN OF STRG-IMMU .........................47
Description ..............................................................47
DTC Logic ...............................................................47
Diagnosis Procedure ..............................................47
B2555 STOP LAMP ...........................................50
Description ..............................................................50
DTC Logic ...............................................................50
Diagnosis Procedure ..............................................50
Component Inspection ............................................51
B2556 PUSH-BUTTON IGNITION SWITCH .....52
Description ..............................................................52
DTC Logic ...............................................................52
Diagnosis Procedure ..............................................52
Component Inspection ............................................53
B2557 VEHICLE SPEED ...................................54
Description ..............................................................54
DTC Logic ...............................................................54
Diagnosis Procedure ..............................................54
B2560 STARTER CONTROL RELAY ...............55
Description ..............................................................55
DTC Logic ...............................................................55
Diagnosis Procedure ...............................................55
B2601 SHIFT POSITION ...................................56
Description ..............................................................56
DTC Logic ...............................................................56
Diagnosis Procedure ...............................................56
Component Inspection ............................................58
B2602 SHIFT POSITION ...................................59
Description ..............................................................59
DTC Logic ...............................................................59
Diagnosis Procedure ...............................................59
B2603 SHIFT POSITION STATUS ....................61
Description ..............................................................61
DTC Logic ...............................................................61
VQ35DE MODELS ....................................................61
VQ35DE MODELS : Diagnosis Procedure .............61
VQ25DE MODELS ....................................................62
VQ25DE MODELS : Diagnosis Procedure .............62
B2604 PNP SWITCH .........................................64
Description ..............................................................64
DTC Logic ...............................................................64
VQ35DE MODELS ....................................................64
VQ35DE MODELS : Diagnosis Procedure .............64
VQ25DE MODELS ....................................................65
VQ25DE MODELS : Diagnosis Procedure .............65
B2605 PNP SWITCH .........................................67
Description ..............................................................67
DTC Logic ...............................................................67
Diagnosis Procedure ...............................................67
B2606 STEERING LOCK RELAY .....................69
Description ..............................................................69
DTC Logic ...............................................................69
Diagnosis Procedure ...............................................69
B2607 STEERING LOCK RELAY .....................70
Description ..............................................................70
DTC Logic ...............................................................70
Diagnosis Procedure ...............................................70
B2608 STARTER RELAY .................................72
Description ..............................................................72
DTC Logic ...............................................................72
Diagnosis Procedure ...............................................72
B2609 STEERING STATUS ..............................74
Description ..............................................................74
DTC Logic ...............................................................74
Diagnosis Procedure ...............................................74
B260B STEERING LOCK UNIT ........................78
Description ..............................................................78
DTC Logic ...............................................................78

SEC-3
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P Diagnosis Procedure ...............................................
78
B260C STEERING LOCK UNIT .........................79
Description ..............................................................79
DTC Logic ...............................................................79
Diagnosis Procedure ...............................................79
B260D STEERING LOCK UNIT .........................80
Description ..............................................................80
DTC Logic ...............................................................80
Diagnosis Procedure ...............................................80
B260F ENGINE STATUS ...................................81
Description ..............................................................81
DTC Logic ...............................................................81
Diagnosis Procedure ...............................................81
B26E1 NO RECEPTION OF ENGINE STA-
TUS SIGNAL ......................................................
82
Description ..............................................................82
DTC Logic ...............................................................82
Diagnosis Procedure ...............................................82
B26E9 STEERING STATUS ..............................83
Description ..............................................................83
DTC Logic ...............................................................83
Diagnosis Procedure ...............................................83
B26EA KEY REGISTRATION ............................84
Description ..............................................................84
DTC Logic ...............................................................84
Diagnosis Procedure ...............................................84
B2612 STEERING STATUS ...............................85
Description ..............................................................85
DTC Logic ...............................................................85
Diagnosis Procedure ...............................................85
B2617 STARTER RELAY CIRCUIT ...................89
Description ..............................................................89
DTC Logic ...............................................................89
Diagnosis Procedure ...............................................89
B2619 BCM ........................................................91
Description ..............................................................91
DTC Logic ...............................................................91
Diagnosis Procedure ...............................................91
B261A PUSH-BUTTON IGNITION SWITCH .....92
Description ..............................................................92
DTC Logic ...............................................................92
Diagnosis Procedure ...............................................92
B261E VEHICLE TYPE ......................................95
Description ..............................................................95
DTC Logic ...............................................................95
Diagnosis Procedure ...............................................95
B2108 STEERING LOCK RELAY ......................96
Description ..............................................................96
DTC Logic ...............................................................96
Diagnosis Procedure ...............................................96
B2109 STEERING LOCK RELAY ....................97
Description ...............................................................97
DTC Logic ................................................................97
Diagnosis Procedure ...............................................97
B210A STEERING LOCK CONDITION
SWITCH .............................................................
98
Description ...............................................................98
DTC Logic ................................................................98
Diagnosis Procedure ...............................................98
B210B STARTER CONTROL RELAY ............102
Description .............................................................102
DTC Logic ..............................................................102
Diagnosis Procedure .............................................102
B210C STARTER CONTROL RELAY ............103
Description .............................................................103
DTC Logic ..............................................................103
Diagnosis Procedure .............................................103
B210D STARTER RELAY ..............................104
Description .............................................................104
DTC Logic ..............................................................104
Diagnosis Procedure .............................................104
B210E STARTER RELAY ...............................105
Description .............................................................105
DTC Logic ..............................................................105
Diagnosis Procedure .............................................105
B210F PNP/CLUTCH INTERLOCK SWITCH .107
Description .............................................................107
DTC Logic ..............................................................107
Diagnosis Procedure .............................................107
B2110 PNP/CLUTCH INTERLOCK SWITCH .109
Description .............................................................109
DTC Logic ..............................................................109
Diagnosis Procedure .............................................109
POWER SUPPLY AND GROUND CIRCUIT ..111
BCM .........................................................................111
BCM : Diagnosis Procedure ..................................111
IPDM E/R ..................................................................111
IPDM E/R : Diagnosis Procedure ..........................111
HOOD SWITCH ...............................................113
Description .............................................................113
Component Function Check ................................113
Diagnosis Procedure ............................................113
Component Inspection ...........................................114
SECURITY INDICATOR LAMP ......................115
Description .............................................................115
Component Function Check ................................115
Diagnosis Procedure .............................................115
Component Inspection ...........................................116
KEY WARNING LAMP ....................................117

SEC-4
Description .............................................................117
Component Function Check ................................117
Diagnosis Procedure .............................................117
HORN FUNCTION ...........................................118
Description .............................................................118
Component Function Check ................................118
Diagnosis Procedure ............................................118
HAZARD FUNCTION .......................................120
Description .............................................................120
Component Function Check ................................120
Diagnosis Procedure .............................................120
INTELLIGENT KEY SYSTEM/ENGINE
START FUNCTION ..........................................
121
Wiring Diagram - INTELLIGENT KEY SYSTEM/
ENGINE START FUNCTION - ..............................
121
NISSAN VEHICLE IMMOBILIZER SYSTEM-
NATS ................................................................
129
Wiring Diagram - NVIS - ........................................129
VEHICLE SECURITY SYSTEM .......................137
Wiring Diagram - VEHICLE SECURITY SYSTEM
- .............................................................................
137
ECU DIAGNOSIS .......................................144
BCM (BODY CONTROL MODULE) ................144
Reference Value ....................................................144
Wiring Diagram - BCM - ........................................167
Fail-safe .................................................................173
DTC Inspection Priority Chart .............................175
DTC Index .............................................................176
IPDM E/R (INTELLIGENT POWER DISTRI-
BUTION MODULE ENGINE ROOM) ...............
178
Reference Value ....................................................178
Wiring Diagram - IPDM E/R - .................................186
Fail-safe .................................................................189
DTC Index .............................................................191
SYMPTOM DIAGNOSIS ............................192
SECURITY CONTROL SYSTEM .....................192
Symptom Table .....................................................192
ENGINE DOES NOT START WHEN INTELLI-
GENT KEY IS INSIDE OF VEHICLE ...............
193
Description .............................................................193
Diagnosis Procedure .............................................193
STEERING DOES NOT LOCK ........................194
Description .............................................................194
Diagnosis Procedure .............................................194
ENGINE DOES NOT START WHEN INTELLI-
GENT KEY IS INSERTED INTO KEY SLOT ...
195
Description ............................................................195
Diagnosis Procedure .............................................195
SECURITY INDICATOR LAMP DOES NOT
TURN ON OR FLASH ......................................
196
Description ............................................................196
Diagnosis Procedure .............................................196
VEHICLE SECURITY SYSTEM CAN NOT BE
SET ...................................................................
197
INTELLIGENT KEY .................................................197
INTELLIGENT KEY : Description ..........................197
INTELLIGENT KEY : Diagnosis Procedure ..........197
DOOR REQUEST SWITCH .....................................197
DOOR REQUEST SWITCH : Description .............197
DOOR REQUEST SWITCH : Diagnosis Proce-
dure .......................................................................
197
VEHICLE SECURITY ALARM DOES NOT
ACTIVATE ........................................................
199
Description ............................................................199
Diagnosis Procedure .............................................199
VEHICLE SECURITY SYSTEM CAN NOT BE
CANCELED ......................................................
200
INTELLIGENT KEY .................................................200
INTELLIGENT KEY : Description ..........................200
INTELLIGENT KEY : Diagnosis Procedure ..........200
DOOR REQUEST SWITCH .....................................200
DOOR REQUEST SWITCH : Description .............200
DOOR REQUEST SWITCH : Diagnosis Proce-
dure .......................................................................
200
KEY SLOT INDICATOR DOES NOT ILLUMI-
NATE ................................................................
201
Description ............................................................201
Diagnosis Procedure .............................................201
PRECAUTION ...........................................202
PRECAUTIONS ................................................202
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
202
Precaution for Procedure without Cowl Top Cover .202
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect .................................
202
ON-VEHICLE REPAIR ..............................204
KEY SLOT ........................................................204
Removal and Installation .......................................204
PUSH BUTTON IGNITION SWITCH ................205
Removal and Installation .......................................205