Control Valve Assembly NISSAN TEANA 2008 Workshop Manual

P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE
SOLENOID VALVE)
TM-73
< COMPONENT DIAGNOSIS >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace damaged parts.
3.CHECK HARNESS BETWEEN TCM AND PRESSURE CONTROL SOLENOID VALVE B (SECONDARY
PRESSURE SOLENOID VALVE) (PART 2)
Check continuity between TCM vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
Check pressure control solenoid valve B (secondary pressure solenoid valve). Refer to TM-73, "
Component
Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)]".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace transaxle assembly. Refer to TM-168, "
Exploded View".
5.DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> Replace TCM. Refer to TM-153, "Exploded View".
NO >> Repair or replace damaged parts.
Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure So-
lenoid Valve)]
INFOID:0000000003849001
1.CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace transaxle assembly. Refer to TM-168, "
Exploded View".
TCM vehicle side harness connector CVT unit vehicle side harness connector
Continuity
Connector Terminal Connector Terminal
F2339F24 3Existed
TCM vehicle side harness connector
GroundContinuity
Connector Terminal
F23 39 Not existed
CVT unit connector
GroundResistance (Approx.)
Connector Terminal
F24 3 3.0 – 9.0 Ω

TM-78
< COMPONENT DIAGNOSIS >[CVT: RE0F09B]
P0841 PRESSURE SENSOR FUNCTION
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
1. Turn ignition switch OFF.
2. Disconnect CVT unit connector.
3. Check pressure control solenoid valve A (line pressure solenoid valve). Refer to TM-78, "
Component
Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace damaged parts.
5.CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
Check pressure control solenoid valve B (secondary pressure solenoid valve). Refer to TM-78, "
Component
Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)]".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace damaged parts.
6.CHECK STEP MOTOR SYSTEM
Check step motor system. Refer to TM-97, "
Description".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace damaged parts.
7.DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> Replace TCM. Refer to TM-153, "Exploded View".
NO >> Repair or replace damaged parts.
Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid
Va l v e ) ]
INFOID:0000000003849008
1.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace transaxle assembly. Refer to TM-168, "
Exploded View".
Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure So-
lenoid Valve)]
INFOID:0000000003849009
1.CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
Check resistance between CVT unit connector terminal and ground.
CVT unit connector
GroundResistance (Approx.)
Connector Terminal
F24 2 3.0 – 9.0 Ω
CVT unit connector
GroundResistance (Approx.)
Connector Terminal
F24 3 3.0 – 9.0 Ω

TM-84
< COMPONENT DIAGNOSIS >[CVT: RE0F09B]
P0868 SECONDARY PRESSURE DOWN
3. Check pressure control solenoid valve B (secondary pressure solenoid valve). Refer to TM-84, "Compo-
nent Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)]".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace damaged parts.
3.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check pressure control solenoid valve A (line pressure solenoid valve). Refer to TM-84, "
Component Inspec-
tion [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.CHECK TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR) SYS-
TEM
Check transmission fluid pressure sensor A (secondary pressure sensor) system. Refer to TM-74, "
DTC
Logic".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace damaged parts.
5.DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> Replace TCM. Refer to TM-153, "Exploded View".
NO >> Repair or replace damaged parts.
Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid
Va l v e ) ]
INFOID:0000000003849016
1.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace transaxle assembly. Refer to TM-168, "
Exploded View".
Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure So-
lenoid Valve)]
INFOID:0000000003849017
1.CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
Check resistance between CVT unit connector terminal and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace transaxle assembly. Refer to TM-168, "
Exploded View".
CVT unit connector
GroundResistance (Approx.)
Connector Terminal
F24 2 3.0 – 9.0 Ω
CVT unit connector
GroundResistance (Approx.)
Connector Terminal
F24 3 3.0 – 9.0 Ω

TCM
TM-121
< ECU DIAGNOSIS >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P Output Speed Sensor (Secondary Speed Sensor)
The shift pattern is changed in accordance with the throttle position when an unexpected signal is sent from
the output speed sensor (secondary speed sensor) to the TCM. The sport mode is inhibited, and the transaxle
is put in “D”.
Input Speed Sensor (Primary Speed Sensor)
The shift pattern is changed in accordance with the throttle position and secondary speed (vehicle speed)
when an unexpected signal is sent from the input speed sensor (primary speed sensor) to the TCM. The sport
mode is inhibited, and the transaxle is put in “D”.
PNP Switch
If an unexpected signal is sent from the PNP switch to the TCM, the transaxle is put in “D”.
CVT Fluid Temperature Sensor
If an unexpected signal is sent from the CVT fluid temperature sensor to the TCM, the gear ratio in use before
receiving the unexpected signal is maintained or the gear ratio is controlled to keep engine speed under 5,000
rpm.
Transmission Fluid Pressure Sensor A (Secondary Pressure Sensor)
 If an unexpected signal is sent from the transmission fluid pressure sensor A (secondary pressure sensor) to
the TCM, the secondary pressure feedback control is stopped and the offset value obtained before the non-
standard condition occurs is used to control line pressure.
 If transmission fluid pressure sensor A (secondary pressure sensor) error signal is inputted to the TCM, sec-
ondary pressure feedback control stops, but line pressure is controlled normally.
Pressure Control Solenoid A (Line Pressure Solenoid Valve)
If an unexpected signal is sent from the solenoid valve to the TCM, the pressure control solenoid A (line pres-
sure solenoid valve) is turned OFF to achieve the maximum fluid pressure.
Pressure Control Solenoid B (Secondary Pressure Solenoid Valve)
If an unexpected signal is sent from the solenoid valve to the TCM, the pressure control solenoid B (secondary
pressure solenoid valve) is turned OFF to achieve the maximum fluid pressure.
Torque Converter Clutch Solenoid Valve
If an unexpected signal is sent from the solenoid valve to the TCM, the torque converter clutch solenoid valve
is turned OFF to cancel the lock-up.
Ste p M oto r
If an unexpected signal is sent from the step motor to the TCM, the step motor coil phases “A” through “D” are
all turned OFF to hold the gear ratio used just before the non-standard condition occurred.
CVT Lock-up Select Solenoid Valve
If an unexpected signal is sent from the solenoid valve to the TCM, the CVT lock-up select solenoid valve is
turned OFF to cancel the lock-up.
TCM Power Supply (Memory Back-up)
Transaxle assembly is protected by limiting the engine torque when the memory back-up power supply (for
controlling) from the battery is not supplied to the TCM. Normal status is restored when turning the ignition
switch OFF to ON after the normal power supply.
DTC Inspection Priority ChartINFOID:0000000003849062
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
NOTE:
If DTC “U1000 CAN COMM CIRCUIT” is indicated with other DTCs, start from a diagnosis for “DTC
U1000 CAN COMMUNICATION LINE”. Refer to TM-41
.
DTC IndexINFOID:0000000003849063
NOTE:
Priority Detected items (DTC)
1 U1000 CAN communication line
2 Except above

TM-124
< SYMPTOM DIAGNOSIS >[CVT: RE0F09B]
SYSTEM SYMPTOM
4
Slips/Will
Not EngageVehicle cannot take
off from “D” position.ON vehicle1. CVT fluid level and stateTM-142
2. CVT positionTM-152
3. CAN communication lineTM-41
4. Line pressure testTM-146
5. Stall testTM-144
6. Step motorTM-97
7. Primary speed sensorTM-52
8. Secondary speed sensorTM-55
9. Accelerator pedal position sensorTM-88
10. CVT fluid temperature sensorTM-50
11. Secondary pressure sensorTM-74
12. TCM power supply and groundTM-85
OFF vehicle13. Oil pump assembly
TM-16814. Forward clutch
15. Control valve
16. Parking components
5Vehicle cannot take
off from “R” position.ON vehicle1. CVT fluid level and stateTM-142
2. CVT positionTM-152
3. CAN communication lineTM-41
4. Line pressure testTM-146
5. Stall testTM-144
6. Step motorTM-97
7. Primary speed sensorTM-52
8. Secondary speed sensorTM-55
9. Accelerator pedal position sensorTM-88
10. CVT fluid temperature sensorTM-50
11. Secondary pressure sensorTM-74
12. TCM power supply and groundTM-85
OFF vehicle13. Oil pump assembly
TM-16814. Reverse brake
15. Control valve
16. Parking components No. Item Symptom Condition Diagnostic item Reference

SYSTEM SYMPTOM
TM-125
< SYMPTOM DIAGNOSIS >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P6
Slips/Will
Not EngageDoes not lock-up.ON vehicle1. CVT fluid level and stateTM-142
2. Line pressure testTM-146
3. Engine speed signalTM-59
4. Primary speed sensorTM-52
5. Torque converter clutch solenoid valveTM-62
6. CAN communication lineTM-41
7. Stall testTM-144
8. Step motorTM-97
9. PNP switchTM-44
10. Lock-up select solenoid valveTM-94
11. CVT fluid temperature sensorTM-50
12. Secondary speed sensorTM-55
13. Secondary pressure sensorTM-74
OFF vehicle14. Torque converterTM-17215. Oil pump assembly
TM-168
16. Control valve
7Does not hold lock-up
condition.ON vehicle1. CVT fluid level and stateTM-142
2. Line pressure testTM-146
3. Engine speed signalTM-59
4. Primary speed sensorTM-52
5. Torque converter clutch solenoid valveTM-62
6. CAN communication lineTM-41
7. Stall testTM-144
8. Step motorTM-97
9. PNP switchTM-44
10. Lock-up select solenoid valveTM-94
11. CVT fluid temperature sensorTM-50
12. Secondary speed sensorTM-55
13. Secondary pressure sensorTM-74
OFF vehicle14. Torque converterTM-17215. Oil pump assembly
TM-168
16. Control valve No. Item Symptom Condition Diagnostic item Reference

TM-126
< SYMPTOM DIAGNOSIS >[CVT: RE0F09B]
SYSTEM SYMPTOM
8
Slips/Will
Not EngageLock-up is not re-
leased.ON vehicle1. CVT fluid level and stateTM-142
2. Line pressure testTM-146
3. Engine speed signalTM-59
4. Primary speed sensorTM-52
5. Torque converter clutch solenoid valveTM-62
6. CAN communication lineTM-41
7. Stall testTM-144
OFF vehicle8. Torque converterTM-1729. Oil pump assembly
TM-168
10. Control valve
9With selector lever in
“D” position, accelera-
tion is extremely poor.ON vehicle1. CVT fluid level and stateTM-142
2. Line pressure testTM-146
3. Stall testTM-144
4. Accelerator pedal position sensorTM-88
5. CAN communication lineTM-41
6. PNP switchTM-44
7. CVT positionTM-152
8. Step motorTM-97
9. Primary speed sensorTM-52
10. Secondary speed sensorTM-55
11. Accelerator pedal position sensorTM-88
12. Primary pressure sensorTM-80
13. Secondary pressure sensorTM-74
14. CVT fluid temperature sensorTM-50
15. TCM power supply and groundTM-85
OFF vehicle16. Torque converterTM-17217. Oil pump assembly
TM-168
18. Forward clutch
19. Control valve No. Item Symptom Condition Diagnostic item Reference

SYSTEM SYMPTOM
TM-127
< SYMPTOM DIAGNOSIS >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
10
Slips/Will
Not EngageWith selector lever in
“R” position, accelera-
tion is extremely poor.ON vehicle1. CVT fluid level and stateTM-142
2. Line pressure testTM-146
3. Stall testTM-144
4. Accelerator pedal position sensorTM-88
5. CAN communication lineTM-41
6. PNP switchTM-44
7. CVT positionTM-152
8. Step motorTM-97
9. Primary speed sensorTM-52
10. Secondary speed sensorTM-55
11. Accelerator pedal position sensorTM-88
12. Primary pressure sensorTM-80
13. Secondary pressure sensorTM-74
14. CVT fluid temperature sensorTM-50
15. TCM power supply and groundTM-85
OFF vehicle16. Torque converterTM-17217. Oil pump assembly
TM-168
18. Reverse brake
19. Control valve
11 Slips at lock-up.ON vehicle1. CVT fluid level and stateTM-142
2. Line pressure testTM-146
3. Engine speed signalTM-59
4. Primary speed sensorTM-52
5. Torque converter clutch solenoid valveTM-62
6. CAN communication lineTM-41
7. Stall testTM-144
8. Step motorTM-97
9. PNP switchTM-44
10. Lock-up select solenoid valveTM-94
11. CVT fluid temperature sensorTM-50
12. Secondary speed sensorTM-55
13. Secondary pressure sensorTM-74
OFF vehicle14. Torque converterTM-17215. Oil pump assembly
TM-168
16. Control valve No. Item Symptom Condition Diagnostic item Reference

TM-128
< SYMPTOM DIAGNOSIS >[CVT: RE0F09B]
SYSTEM SYMPTOM
12 Others No creep at all.ON vehicle1. CVT fluid level and stateTM-142
2. Line pressure testTM-146
3. Accelerator pedal position sensorTM-88
4. PNP switchTM-44
5. CAN communication lineTM-41
6. Stall testTM-144
7. CVT positionTM-152
8. Step motorTM-97
9. Primary speed sensorTM-52
10. Secondary speed sensorTM-55
11. Accelerator pedal position sensorTM-88
12. CVT fluid temperature sensorTM-50
13. Primary pressure sensorTM-80
14. Secondary pressure sensorTM-74
15. TCM power supply and groundTM-85
OFF vehicle16. Torque converterTM-172
17. Oil pump assembly
TM-168
18. Gear system
19. Forward clutch
20. Reverse brake
21. Control valve No. Item Symptom Condition Diagnostic item Reference

SYSTEM SYMPTOM
TM-129
< SYMPTOM DIAGNOSIS >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
13
OthersVehicle cannot drive
in all positions.ON vehicle1. CVT fluid level and stateTM-142
2. Line pressure testTM-146
3. PNP switchTM-44
4. Stall testTM-144
5. CVT positionTM-152
6. Step motorTM-97
7. Primary speed sensorTM-52
8. Secondary speed sensorTM-55
9. Accelerator pedal position sensorTM-88
10. CVT fluid temperature sensorTM-50
11. Secondary pressure sensorTM-74
12. TCM power supply and groundTM-85
OFF vehicle13. Torque converterTM-172
14. Oil pump assembly
TM-168
15. Gear system
16. Forward clutch
17. Reverse brake
18. Control valve
19. Parking components
14With selector lever in
“D” position, driving is
not possible.ON vehicle1. CVT fluid level and stateTM-142
2. Line pressure testTM-146
3. PNP switchTM-44
4. Stall testTM-144
5. CVT positionTM-152
6. Step motorTM-97
7. Primary speed sensorTM-52
8. Secondary speed sensorTM-55
9. Accelerator pedal position sensorTM-88
10. CVT fluid temperature sensorTM-50
11. Secondary pressure sensorTM-74
12. TCM power supply and groundTM-85
OFF vehicle13. Torque converterTM-172
14. Oil pump assembly
TM-168
15. Gear system
16. Forward clutch
17. Control valve
18. Parking components No. Item Symptom Condition Diagnostic item Reference