lock NISSAN TEANA 2008 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2008, Model line: TEANA, Model: NISSAN TEANA 2008Pages: 5121, PDF Size: 69.03 MB
Page 3436 of 5121
![NISSAN TEANA 2008 Service Manual PCS
DIAGNOSIS SYSTEM (BCM)
PCS-45
< FUNCTION DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
Test item Description
BATTERY SAVERThis test is able to check interior room lamp opera NISSAN TEANA 2008 Service Manual PCS
DIAGNOSIS SYSTEM (BCM)
PCS-45
< FUNCTION DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
Test item Description
BATTERY SAVERThis test is able to check interior room lamp opera](/img/5/57391/w960_57391-3435.png)
PCS
DIAGNOSIS SYSTEM (BCM)
PCS-45
< FUNCTION DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
Test item Description
BATTERY SAVERThis test is able to check interior room lamp operation.
The interior room lamp will be activated when “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SETNOTE:
This item is displayed, but cannot be used.
OUTSIDE BUZZERThis test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated when “ON” on CONSULT-III screen is touched.
INSIDE BUZZERThis test is able to check warning chime in combination meter operation.
Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
Key warning chime sounds when “KEY” on CONSULT-III screen is touched.
P position warning chime sounds when “KNOB” on CONSULT-III screen is touched.
INDICATORThis test is able to check warning lamp operation.
“KEY” Warning lamp illuminates when “RED ON” on CONSULT-III screen is touched.
“KEY” Warning lamp blinks when “RED IND” on CONSULT-III screen is touched.
INT LAMPThis test is able to check interior room lamp operation.
The interior room lamp will be activated when “ON” on CONSULT-III screen is touched.
LCDThis test is able to check meter display information
Engine start information displays when “BP N” on CONSULT-III screen is touched.
Engine start information displays when “BP I” on CONSULT-III screen is touched.
Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
P position warning displays when “SFT P” on CONSULT-III screen is touched.
Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
Take away warning displays when “OUTKEY” on CONSULT-III screen is touched.
OFF position warning displays when “LK WN” on CONSULT-III screen is touched.
TRUNK/GLASS HATCHThis test is able to check trunk lid opener actuator open operation.
This actuator opens when “OPEN” on CONSULT-III screen is touched.
FLASHERThis test is able to check security hazard lamp operation.
The hazard lamps will be activated when “RH” or “LH”on CONSULT-III screen is touched.
HORNThis test is able to check horn operation.
The horn will be activated when “ON” on CONSULT-III screen is touched.
P RANGEThis test is able to check control device power supply
Control device power is supplied when “ON” on CONSULT-III screen is touched.
ENGINE SW ILLUMIThis test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.
LOCK INDICATORThis test is able to check LOCK indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
ACC INDICATORThis test is able to check ACC indicator in push-ignition switch operation.
ACC indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
IGNITION ON INDThis test is able to check ON indicator in push-ignition switch operation.
ON indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
KEY SLOT ILLUMIThis test is able to check key slot illumination operation.
Key slot illumination illuminates when “ON” on CONSULT-III screen is touched.
TRUNK/BACK DOORThis test is able to check trunk lid opener actuator open operation.
This actuator opens when “OPEN” on CONSULT-III screen is touched.
Page 3440 of 5121
![NISSAN TEANA 2008 Service Manual PCS
B2553 IGNITION RELAY
PCS-49
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
B2553 IGNITION RELAY
DescriptionINFOID:0000000003805734
BCM turns ON the following rela NISSAN TEANA 2008 Service Manual PCS
B2553 IGNITION RELAY
PCS-49
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
B2553 IGNITION RELAY
DescriptionINFOID:0000000003805734
BCM turns ON the following rela](/img/5/57391/w960_57391-3439.png)
PCS
B2553 IGNITION RELAY
PCS-49
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
B2553 IGNITION RELAY
DescriptionINFOID:0000000003805734
BCM turns ON the following relays to ignition power supply to each ECU when the ignition switch is turned
ON.
Ignition relay (inserted into fuse box)
Ignition relay (built into IPDM E/R)
Blower relay
BCM checks any ignition relay ON request for consistency with the actual ignition relay operation status.
DTC LogicINFOID:0000000003805735
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions (start the engine), and wait for at least 2 seconds.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to PCS-49, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003805736
1.CHECK DTC WITH IPDM E/R
Check “Self diagnostic result” with CONSULT-III. Refer to PCS-120, "
DTCIndex".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace malfunctioning parts.
2.CHECK FUSE
Check that the following fuse is not fusing.
Is the fuse fusing?
YES >> Repair the applicable circuit. And then replace the fuse.
NO >> GO TO 3.
3.CHECK IGNITION RELAY FEEDBACK INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector and ground.
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B2553 IGNITION RELAYBCM detects a difference of signal for 2 seconds or
more between the following information.
Ignition relay (fuse block) ON/OFF operation
Ignition relay (fuse block) feedback. Harness or connectors
(ignition relay feedback circuit is
open or short)
Fuse
Ignition relay
IPDM E/R
Signal name Connection position Fuse No. Capacity
Ignition power supply FUSE BLOCK (J/B) 3 10A
Page 3441 of 5121
![NISSAN TEANA 2008 Service Manual PCS-50
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
B2553 IGNITION RELAY
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK IGNITION RELAY FEEDBACK CIRCUIT
1. Disconnect fus NISSAN TEANA 2008 Service Manual PCS-50
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
B2553 IGNITION RELAY
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK IGNITION RELAY FEEDBACK CIRCUIT
1. Disconnect fus](/img/5/57391/w960_57391-3440.png)
PCS-50
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
B2553 IGNITION RELAY
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK IGNITION RELAY FEEDBACK CIRCUIT
1. Disconnect fuse block (J/B) connector.
2. Check continuity between BCM harness connector and fuse block (J/B) harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair or replace harness.
5.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
(+)
(–) ConditionVoltage (V)
(Approx.) BCM
Connector Terminal
M123 123 Ground Ignition switchOFF 0
ON Battery voltage
BCM FUSE BLOCK (J/B)
Continuity
Connector Terminal Connector Terminal
M123 123 M1 2A Existed
BCM
GroundContinuity
Connector Terminal
M123 123 Not existed
Page 3442 of 5121
![NISSAN TEANA 2008 Service Manual PCS
B260A IGNITION RELAY
PCS-51
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
B260A IGNITION RELAY
DescriptionINFOID:0000000003805737
When the ignition switch is tur NISSAN TEANA 2008 Service Manual PCS
B260A IGNITION RELAY
PCS-51
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
B260A IGNITION RELAY
DescriptionINFOID:0000000003805737
When the ignition switch is tur](/img/5/57391/w960_57391-3441.png)
PCS
B260A IGNITION RELAY
PCS-51
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
B260A IGNITION RELAY
DescriptionINFOID:0000000003805737
When the ignition switch is turned ON, the BCM activates the following relays to provide power supply to each
ECU.
Ignition relay (inserted into fuse block)
Ignition relay (built into IPDM E/R)
Blower fan motor relay
BCM checks any ignition relay ON request for consistency with the actual ignition relay operation status.
DTC LogicINFOID:0000000003805738
DTC DETECTION LOGIC
NOTE:
If DTC B260A is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
PCS-46, "
BCM : DTC Logic".
If DTC B260A is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
PCS-48, "
BCM : DTC Logic".
If DTC B260A is displayed with DTC B261A, first perform the trouble diagnosis for DTC B261A. Refer to
PCS-60, "
DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions, and wait for at least 2 seconds.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to PCS-51, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003805739
1.CHECK DTC WITH IPDM E/R
Check “Self diagnostic result” with CONSULT-III. Refer to PCS-120, "
DTCIndex".
Is DTC detected?
YES >> Repair or replace the malfunctioning parts.
NO >> GO TO 2.
2.CHECK IGNITION RELAY INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check voltage between BCM harness connector and ground.
Is the inspection result normal?
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B260A IGNITION RELAYBCM detects a difference of signal for 2 seconds or
more between the following information.
Ignition relay (IPDM E/R) operation request
Ignition relay feedback from IPDM E/R (CAN). Harness or connectors
(Ignition relay operation circuit is
open or shorted.)
IPDM E/R
(+)
(–)Voltage (V)
(Approx.) BCM
Connector Terminal
M121 47 Ground Battery voltage
Page 3448 of 5121
![NISSAN TEANA 2008 Service Manual PCS
B2616 IGNITION RELAY CIRCUIT
PCS-57
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
B2616 IGNITION RELAY CIRCUIT
DescriptionINFOID:0000000003805748
BCM controls th NISSAN TEANA 2008 Service Manual PCS
B2616 IGNITION RELAY CIRCUIT
PCS-57
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
B2616 IGNITION RELAY CIRCUIT
DescriptionINFOID:0000000003805748
BCM controls th](/img/5/57391/w960_57391-3447.png)
PCS
B2616 IGNITION RELAY CIRCUIT
PCS-57
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
B2616 IGNITION RELAY CIRCUIT
DescriptionINFOID:0000000003805748
BCM controls the various electrical components and simultaneously supplies power according to the power
supply position.
BCM checks the power supply position internally.
DTC LogicINFOID:0000000003805749
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions, and wait for at least 1 second.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to PCS-57, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003805750
1.CHECK IGNITION RELAY POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect ignition relay.
3. Check voltage between ignition relay harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK IGNITION RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between ignition relay harness connector and BCM harness connector.
4. Check continuity between ignition relay harness connector and ground.
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B2616 Ignition relay circuitAn immediate operation of ignition relay (fuse
block) is requested by BCM, but there is no re-
sponse for more than 1 second Harness or connectors
(Ignition relay circuit is open or
shorted)
Ignition relay (Fuse block)
(+)
(–) ConditionVoltage (V)
(Approx.) Ignition relay
Te r m i n a l
1 Ground Ignition switchOFF or ACC 0
ON Battery voltage
Ignition relay BCM
Continuity
Terminal Connector Terminal
1 M122 82 Existed
Page 3457 of 5121
![NISSAN TEANA 2008 Service Manual PCS-66
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
DescriptionINFOID:0000000003805763
The switch th NISSAN TEANA 2008 Service Manual PCS-66
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
DescriptionINFOID:0000000003805763
The switch th](/img/5/57391/w960_57391-3456.png)
PCS-66
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
DescriptionINFOID:0000000003805763
The switch that changes the power supply position.
BCM maintains the power supply position status.
BCM changes the power supply position with the operation of the push-button ignition switch.
Component Function CheckINFOID:0000000003805764
1.CHECK FUNCTION
Check push-button ignition switch (“LOCK INDICATOR”, “ACC INDICATOR” and “IGNITION ON IND”) in
Active Test Mode with CONSULT-III.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Refer to PCS-66, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000003805765
1.CHECK PUSH-BUTTON IGNITION SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch connector.
3. Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check the following.
10A fuse [No.9, located in fuse block (J/B)]
Harness for open or short between push-button ignition switch and fuse
2.CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and push-button ignition switch harness connector.
3. Check continuity between BCM harness connector and ground.
Te s t i t e m D e s c r i p t i o n
LOCK INDICATOR
ACC INDICATOR
IGNITION ON INDON
Position indicator Illuminates
OFF Does not illuminate
(+)
(–)Voltage (V)
(Approx.) Push-button ignition switch
Connector Terminal
M101 8 Ground Battery voltage
IndicatorBCM Push-button ignition switch
Continuity
Connector Terminal Connector Terminal
LOCK M123 134
M1015
Existed ACC M119 15 6
ON M122 93 7
Page 3458 of 5121
![NISSAN TEANA 2008 Service Manual PCS
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PCS-67
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P NIs the inspection result normal?
YES >> GO TO 3.
NO >> Repair NISSAN TEANA 2008 Service Manual PCS
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PCS-67
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P NIs the inspection result normal?
YES >> GO TO 3.
NO >> Repair](/img/5/57391/w960_57391-3457.png)
PCS
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PCS-67
< COMPONENT DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P NIs the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK PUSH-BUTTON IGNITION SWITCH
Refer to PCS-67, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace push-button ignition switch. Refer to PCS-127, "
Removal and Installation".
4.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000003805766
1.CHECK PUSH-BUTTON IGNITION SWITCH
1. Turn ignition switch OFF.
2. Disconnect push-button ignition switch connector.
3. Check continuity between push-button ignition switch terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace push-button ignition switch. Refer to PCS-127, "
Removal and Installation".
IndicatorBCM
GroundContinuity
Connector Terminal
LOCK M123 134
Not existed ACC M119 15
ON M122 93
Te r m i n a l
Continuity Push-button ignition switch
(+) (-)
58Not existed
85Existed
68Not existed
86Existed
78Not existed
87Existed
Page 3465 of 5121
![NISSAN TEANA 2008 Service Manual PCS-74
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
BCM (BODY CONTROL MODULE)
DOOR SW-RLRear LH door closed Off
Rear LH door opened On
DOOR SW-BKNOTE:
The item is indicated, but not monitored. Off
CDL NISSAN TEANA 2008 Service Manual PCS-74
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
BCM (BODY CONTROL MODULE)
DOOR SW-RLRear LH door closed Off
Rear LH door opened On
DOOR SW-BKNOTE:
The item is indicated, but not monitored. Off
CDL](/img/5/57391/w960_57391-3464.png)
PCS-74
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
BCM (BODY CONTROL MODULE)
DOOR SW-RLRear LH door closed Off
Rear LH door opened On
DOOR SW-BKNOTE:
The item is indicated, but not monitored. Off
CDL LOCK SWOther than power door lock switch LOCK Off
Power door lock switch LOCK On
CDL UNLOCK SWOther than power door lock switch UNLOCK Off
Power door lock switch UNLOCK On
KEY CYL LK-SWNOTE:
The item is indicated, but not monitored. Off
KEY CYL UN-SWNOTE:
The item is indicated, but not monitored. Off
KEY CYL SW-TRNOTE:
The item is indicated, but not monitored. Off
HAZARD SWHazard switch is OFF Off
Hazard switch is ON On
REAR DEF SW
NOTE:
At model with BOSE au-
dio system this item is in-
dicated, but is not
monitored.Rear window defogger switch is OFF Off
Rear window defogger switch is ON On
TR CANCEL SWNOTE:
The item is indicated, but not monitored. Off
TR/BD OPEN SWTrunk lid opener switch OFF Off
While the trunk lid opener switch is turned ON On
TRNK/HAT MNTRTrunk lid closed Off
Trunk lid opened On
RKE-LOCKLOCK button of the key is not pressed Off
LOCK button of the key is pressed On
RKE-UNLOCKUNLOCK button of the key is not pressed Off
UNLOCK button of the key is pressed On
RKE-TR/BDTRUNK OPEN button of the key is not pressed Off
TRUNK OPEN button of the key is pressed On
RKE-PANICNOTE:
The item is indicated, but not monitored. Off
RKE-P/W OPENNOTE:
The item is indicated, but not monitored. Off
RKE-MODE CHGLOCK/UNLOCK button of the key is not pressed and held simulta-
neouslyOff
LOCK/UNLOCK button of the key is pressed and held simulta-
neouslyOn
OPTICAL SENSORBright outside of the vehicle Close to 5 V
Dark outside of the vehicle Close to 0 V
REQ SW -DRDriver door request switch is not pressed Off
Driver door request switch is pressed On
REQ SW -ASPassenger door request switch is not pressed Off
Passenger door request switch is pressed On Monitor Item Condition Value/Status
Page 3466 of 5121
![NISSAN TEANA 2008 Service Manual PCS
BCM (BODY CONTROL MODULE)
PCS-75
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off
REQ SW -RRNOTE:
The item i NISSAN TEANA 2008 Service Manual PCS
BCM (BODY CONTROL MODULE)
PCS-75
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off
REQ SW -RRNOTE:
The item i](/img/5/57391/w960_57391-3465.png)
PCS
BCM (BODY CONTROL MODULE)
PCS-75
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L B A
O
P N
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off
REQ SW -BD/TRTrunk lid opener request switch is not pressed Off
Trunk lid opener request switch is pressed On
PUSH SWPush-button ignition switch (push switch) is not pressed Off
Push-button ignition switch (push switch) is pressed On
IGN RLY2 -F/BIgnition switch in OFF or ACC position Off
Ignition switch in ON position On
CLUCH SWNOTE:
The item is indicated, but not monitored. Off
BRAKE SW 1The brake pedal is not depressed On
The brake pedal is depressed Off
DETE/CANCL SWSelector lever in P position Off
Selector lever in any position other than P On
SFT PN/N SWSelector lever in any position other than P and N Off
Selector lever in P or N position On
S/L -LOCKSteering is locked Off
Steering is unlocked On
S/L -UNLOCKSteering is unlocked Off
Steering is locked On
S/L RELAY-F/BIgnition switch in OFF or ACC position Off
Ignition switch in ON position On
UNLK SEN -DRDriver door is unlocked Off
Driver door is locked On
PUSH SW -IPDMPush-button ignition switch (push-switch) is not pressed Off
Push-button ignition switch (push-switch) is pressed On
IGN RLY1 -F/BIgnition switch in OFF or ACC position Off
Ignition switch in ON position On
DETE SW -IPDMSelector lever in P position Off
Selector lever in any position other than P On
SFT PN -IPDMSelector lever in any position other than P and N Off
Selector lever in P or N position On
SFT P -METSelector lever in any position other than P Off
Selector lever in P position On
SFT N -METSelector lever in any position other than N Off
Selector lever in N position On
ENGINE STATEEngine stopped Stop
While the engine stalls Stall
At engine cranking Crank
Engine running Run
S/L LOCK-IPDMSteering is locked Off
Steering is unlocked On Monitor Item Condition Value/Status
Page 3467 of 5121
![NISSAN TEANA 2008 Service Manual PCS-76
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
BCM (BODY CONTROL MODULE)
S/L UNLK-IPDMSteering is unlocked Off
Steering is locked On
S/L RELAY-REQIgnition switch in OFF or ACC position Off
Igniti NISSAN TEANA 2008 Service Manual PCS-76
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
BCM (BODY CONTROL MODULE)
S/L UNLK-IPDMSteering is unlocked Off
Steering is locked On
S/L RELAY-REQIgnition switch in OFF or ACC position Off
Igniti](/img/5/57391/w960_57391-3466.png)
PCS-76
< ECU DIAGNOSIS >[POWER DISTRIBUTION SYSTEM]
BCM (BODY CONTROL MODULE)
S/L UNLK-IPDMSteering is unlocked Off
Steering is locked On
S/L RELAY-REQIgnition switch in OFF or ACC position Off
Ignition switch in ON position On
VEH SPEED 1 While driving Equivalent to speedometer reading
VEH SPEED 2 While driving Equivalent to speedometer reading
DOOR STAT-DRDriver door is locked LOCK
Wait with selective UNLOCK operation (5 seconds) READY
Driver door is unlocked UNLOCK
DOOR STAT-ASPassenger door is locked LOCK
Wait with selective UNLOCK operation (5 seconds) READY
Passenger door is unlocked UNLOCK
ID OK FLAGIgnition switch in ACC or ON position Reset
Ignition switch in OFF position Set
PRMT ENG STRTThe engine start is prohibited Reset
The engine start is permitted Set
PRMT RKE STRTNOTE:
The item is indicated, but not monitored. Reset
KEY SW -SLOTThe key is not inserted into key slot Off
The key is inserted into key slot On
RKE OPE COUN1 During the operation of the key Operation frequency of the key
RKE OPE COUN2NOTE:
The item is indicated, but not monitored. —
CONFRM ID ALLThe key ID that the key slot receives does not accord with any key
ID registered to BCM.Ye t
The key ID that the key slot receives accords with any key ID regis-
tered to BCM.Done
CONFIRM ID4The key ID that the key slot receives does not accord with the fourth
key ID registered to BCM.Ye t
The key ID that the key slot receives accords with the fourth key ID
registered to BCM.Done
CONFIRM ID3The key ID that the key slot receives does not accord with the third
key ID registered to BCM.Ye t
The key ID that the key slot receives accords with the third key ID
registered to BCM.Done
CONFIRM ID2The key ID that the key slot receives does not accord with the sec-
ond key ID registered to BCM.Ye t
The key ID that the key slot receives accords with the second key
ID registered to BCM.Done
CONFIRM ID1The key ID that the key slot receives does not accord with the first
key ID registered to BCM.Ye t
The key ID that the key slot receives accords with the first key ID
registered to BCM.Done
TP 4The ID of fourth key is not registered to BCM Yet
The ID of fourth key is registered to BCM Done
TP 3The ID of third key is not registered to BCM Yet
The ID of third key is registered to BCM Done Monitor Item Condition Value/Status