display NISSAN TEANA 2014 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2014, Model line: TEANA, Model: NISSAN TEANA 2014Pages: 4801, PDF Size: 51.2 MB
Page 3278 of 4801

MWI
COMBINATION METERMWI-23
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
M B
A
O P
CRUISE W/L Ignition switch ON CRUISE warning indication On
CRUISE warning indication Off
CVT IND Ignition switch ON CVT indicator ON On
CVT indicator OFF Off
SET IND Ignition switch ON SET indicator ON On
SET indicator OFF Off
FUEL LOW SIG Ignition switch ON During low fuel level indication On
Except during low fuel level indication Off
O/D OFF IND Ignition switch ON O/D OFF indicator ON On
O/D OFF indicator OFF Off
FUEL W/L Ignition switch ON During low fuel level indication On
Except during low fuel level indication Off
WASHER W/L Ignition switch ON Low washer fluid warning indication On
Except during low washer fluid warning in-
dication Off
AIR PRES W/L Tire pressure warn-
ing lamp operation When tire pressure
warning lamp is ON On
When tire pressure wa rning lamp is OFF Off
KEY G/Y W/L Ignition switch ON During Intelligent Key system malfunction
indication On
Other than the above Off
EPS W/L Ignition switch ON EPS warning lamp ON On
EPS warning lamp OFF Off
LCD Ignition switch ACC During engine start information indication B&P
ACC SET SPEED Ignition switch ON During set vehicle speed indicator not dis-
played Off
During set vehicle speed indicator dis-
played Indicates the set vehicle speed
ACC UNIT Ignition switch ON Set vehicle speed indicator unit display ON On
Set vehicle speed indicator unit display
OFF Off
SHIFT IND Ignition switch ON Position of shift selector [P, R, N, D, DS]
FUEL CAP W/L Ignition switch ON Fuel filler cap warning display ON On
Fuel filler cap warning display OFF Off
O/D OFF SW Ignition switch ON Overdrive control switch ON On
Overdrive control switch OFF Off
M RANGE SW Ignition switch ON Shift selector in manual mode position On
Other than the above Off
NM RANGE SW Ignition switch ON Shift selector in manual mode position Off
Other than the above On
AT SFT UP SW Ignition switch ON Shift selector operated in the up position On
Other than the above Off
AT SFT DWN SW Ignition switch ON Shift selector operated in the down position On
Other than the above Off
ST SFT UP SW Ignition switch ON Paddle shifter operated in up position On
Shift selector is in non manual mode up
position Off
Monitor Item Condition Value/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3279 of 4801

MWI-24
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
TERMINAL LAYOUT
PHYSICAL VALUES
ST SFT DWN SW Ignition switch ON Paddle shifter operated in down position On
Other than the above Off
PKB SW Ignition switch ON Parking brake switch ON On
Parking brake switch OFF Off
BUCKLE SW Ignition switch ON Driver seat belt not fastened On
Driver seat belt fastened Off
EPS W/L Ignition switch ON EPS warning lamp ON On
EPS warning lamp OFF Off
BRAKE OIL SW Ignition switch ON Brake fluid level switch ON On
Brake fluid level switch OFF Off
PASS BUCKLE SW Ignition switch ON Passenger seat belt not fastened On
Passenger seat belt fastened Off
DISTANCE
[mile] or [km] Ignition switch ON — Distance to empty
OUTSIDE TEMP
[ ° F] or [ °C] Ignition switch ON — Displays the ambient air tempera-
ture which is input from the ambient
sensor
BUZZER Ignition switch ON Buzzer ON On
Buzzer OFF Off
TPMS MALF Ignition switch ON Low tire pressure
warning lamp ON On
Low tire pressure warning lamp OFF Off
BSW IND Ignition switch ON BSW indicator ON On
BSW indicator OFF Off
LDW IND Ignition switch ON LDW indicator ON On
LDW indicator OFF Off
Monitor Item Condition Value/Status
WKIA5724E
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
1
(B) Ground Ground Input Ignition
switch
OFF — Battery voltage
2
(B) Ground Ground Input Ignition
switch
ON — Battery voltage
3
(P) Ground Steering switch input 1 — — — —
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3282 of 4801

MWI
COMBINATION METERMWI-27
< ECU DIAGNOSIS INFORMATION >
C
D E
F
G H
I
J
K L
M B
A
O PFail-SafeINFOID:0000000009461695
FA I L - S A F E
The combination meter activates the fail-safe contro l if CAN communication with each unit is malfunctioning.
DTC IndexINFOID:0000000009461696
52
(P) Ground O/D OFF/SPORT switch Input Ignition
switch
ON O/D OFF switch pressed 0 V
Other than the above 5 V
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
Function Specifications
Speedometer Reset to zero by suspending communication.
Tachometer
Engine coolant temperature gauge
Illumination control When suspending communication, changes to nighttime mode.
Information display Odo/trip meter An indicated value is maintained at communications blackout.
Shift position indicator The display turns OFF by suspending communication.
Warning messages The display turns OFF by suspending communication.
Buzzer The buzzer turns OFF by suspending communication.
Warning lamp/indicator lamp ABS warning lamp
The lamp turns ON by suspending communication.
O/D OFF indicator lamp
Slip indicator lamp
Brake warning lamp
Malfunction indicator lamp
VDC OFF indicator lamp
EPS warning lamp
Low tire pressure warning lamp The lamp blinking caused by suspending communication.
High beam indicator lamp
The lamp turns OFF by suspending communication.
Turn signal indicator lamp
Master warning lamp
Front lamp indicator lamp
Lane departure warning
Tail lamp indicator lamp
Air bag warning lamp
The lamp turns off when disconnected.
Charge warning lamp
Seat belt warning lamp
Security indicator lamp
Display contents of CONSULT Diagnostic item is detected when... Refer to
CAN COMM CIRCUIT
[U1000] When combination meter is not transmitting or receiving CAN communication signal for 2
seconds or more. MWI-53
CONTROL UNIT (CAN)
[U1010] When detecting error during the initial diagnosis of the CAN controller of combination
meter. MWI-54
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3283 of 4801
![NISSAN TEANA 2014 Service Manual
MWI-28
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
VEHICLE SPEED CIRC
[B2205] The abnormal vehicl
e speed signal is input from the ABS actuator and electric unit (control
unit) for 2 seconds NISSAN TEANA 2014 Service Manual
MWI-28
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
VEHICLE SPEED CIRC
[B2205] The abnormal vehicl
e speed signal is input from the ABS actuator and electric unit (control
unit) for 2 seconds](/img/5/57390/w960_57390-3282.png)
MWI-28
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
VEHICLE SPEED CIRC
[B2205] The abnormal vehicl
e speed signal is input from the ABS actuator and electric unit (control
unit) for 2 seconds or more. MWI-55
TACHO METER
[B2267] If ECM continuously transmits abnormal engine speed signals for 2 seconds or more.
MWI-56
WATER TEMP METER
[B2268] If ECM continuously transmits abnormal engine coolant temperature signals for 60 sec-
onds or more. MWI-57
Display contents of CONSULT Diagnostic item is detected when... Refer to
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3307 of 4801

MWI-52
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
Are self-diagnosis results normal?
YES >> GO TO 4.
NO >> GO TO 5.
4.NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts.
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES >> Inspection End.
NO >> GO TO 1.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3309 of 4801

MWI-54
< DTC/CIRCUIT DIAGNOSIS >
U1010 CONTROL UNIT (CAN)
U1010 CONTROL UNIT (CAN)
DescriptionINFOID:0000000009461703
Initial diagnosis of combination meter.
DTC LogicINFOID:0000000009461704
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000009461705
1.REPLACE COMBINATION METER
When DTC U1010 is detected, replace combination meter. Refer to MWI-82, "Removal and Installation"
.
>> Inspection End.
DTC Display contents of CONSULT Detection condition Possible malfunction
U1010 CONTROL UNIT (CAN) When detecting error during the initial diagnosis of
the CAN controller of combination meter. Combination meter
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3321 of 4801

MWI-66
< DTC/CIRCUIT DIAGNOSIS >
AMBIENT SENSOR SIGNAL CIRCUIT
AMBIENT SENSOR SIGNAL CIRCUIT
DescriptionINFOID:0000000009461729
Transmits the ambient sensor signal to the IPDM E/R.
Component Function CheckINFOID:0000000009461730
1.COMBINATION METER INPUT SIGNAL
1. Select METER/M&A on CONSULT.
2. Check OUTSIDE TEMP on DATA MONITOR.
Does the ambient temperature approx imately match the CONSULT display?
YES >> Replace combination meter. Refer to MWI-82, "Removal and Installation".
NO >> Refer to MWI-66, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009461731
Regarding Wiring Diagram information, refer to MWI-32, "Wiring Diagram".
1.CHECK AMBIENT SENSOR CIRCUITS BETWEE N COMBINATION METER AND IPDM E/R
1. Disconnect combination meter connecto r M24 and IPDM E/R connector E63.
2. Check continuity between combination meter har ness connector M24 terminals 30, 31 and IPDM E/R har-
ness connector E63 terminals 49 and 50.
3. Check continuity between combination mete r harness connector M24 terminals 30, 31 and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connector.
2.CHECK AMBIENT SENSOR CIRCUITS BETW EEN IPDM E/R AND AMBIENT SENSOR
1. Disconnect IPDM E/R connector E201 and ambient sensor connector E211.
2. Check continuity between IPDM E/R harness connec tor E201 terminals 87, 95 and ambient sensor har-
ness connector E211 terminals 1 and 2.
3. Check continuity between IPDM E/R har ness connector E201 terminals 87, 95 and ground.
Is the inspection result normal?
Connector Terminal Connector Terminal Continuity M24 30
E63 49
Ye s
31 50
Connector Terminal Continuity M24 30
No
31
Connector Terminal Connector Terminal Continuity
E201 87
E211 1
Ye s
95 2
Connector Terminal Continuity E201 87 No
95
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3325 of 4801

MWI-70
< DTC/CIRCUIT DIAGNOSIS >
STEERING SWITCH
STEERING SWITCH
DescriptionINFOID:0000000009461735
When one of the steering switches is pushed, the resistance in the steering switch changes the signal to
identify which button is controlling the information display.
Diagnosis ProcedureINFOID:0000000009461736
Regarding Wiring Diagram information, refer to MWI-32, "Wiring Diagram".
1.CHECK STEERING SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter harness connector M24 and spiral cable harness connector M30.
3. Check continuity between combination meter har ness connector M24 and spiral cable harness connector
M30.
4. Check continuity between combination meter harness connector M24 and ground.
Is the inspection results normal?
YES >> Inspection End.
NO >> Repair or replace harness or connectors.
Component InspectionINFOID:0000000009461737
1.CHECK STEERING SWITCH RESISTANCE
Check resistance between the following steering switch terminals.
Is the inspection results normal?
YES >> GO TO 2.
NO >> Replace steering wheel switch. Refer to AV-51, "Removal and Installation"
.
Combination meter Spiral cable
Continuity
Connector Terminal Connector Terminal
M24 3
M30 24
Ye s
431
24 33
Combination meter GroundContinuity
Connector Terminal
M24 3
No
4
24
Terminal Signal name Condition Resistance (
Ω)
(Approx.)
14
17 Display Depress DISPLAY switch.
†2023
Back Depress BACK switch. 723
15 Enter Depress ENTER switch. 2023
Menu Up Depress ENTER switch up. 121
Menu Down Depress ENTER switch down. 321
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3329 of 4801

MWI-74
< SYMPTOM DIAGNOSIS >
THE OIL PRESSURE WARNING CONTINUES DISPLAYING, OR DOES NOT DIS-
PLAY
THE OIL PRESSURE WARNING CONT INUES DISPLAYING, OR DOES
NOT DISPLAY
DescriptionINFOID:0000000009461742
• The low oil pressure warning message stays on when oil pressure is normal.
• The low oil pressure warning message stays off when oil pressure is low.
Diagnosis ProcedureINFOID:0000000009461743
1.CHECK COMBINATION METER INPUT
1. Start the engine and select METER/M&A on CONSULT.
2. Observe OIL W/L DATA MONITOR and the operation of the low oil pressure warning message in the
information display.
Is the inspection result normal?
YES >> Perform ECM self-diagnosis. Refer to (QR25DE) EC-77, "CONSULT Function" or (VQ35DE) EC-
601, "CONSULT Function".
NO >> Replace combination meter. Refer to MWI-82, "Removal and Installation"
.
Component Condi tion CONSULT
Low oil pressure warning message Engine running OFF
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3330 of 4801

MWI
THE PARKING BRAKE RELEASE WARNING CONTINUES DISPLAYING, OR
DOES NOT DISPLAY
MWI-75
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
K L
M B
A
O P
THE PARKING BRAKE RELEASE WA RNING CONTINUES DISPLAYING,
OR DOES NOT DISPLAY
DescriptionINFOID:0000000009461744
• The parking brake warning is displayed while driving the vehicle even though the parking brake is released.
• The parking brake warning is not displayed even though driving the vehicle with the parking brake
depressed.
Diagnosis ProcedureINFOID:0000000009461745
1.CHECK PARKING BRAKE WARNING LAMP OPERATION
1. Start engine.
2. Check the operation of the brake warni ng lamp while operating the parking brake.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-82, "Removal and Installation".
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Check the parking brake switch signal circuit. Refer to MWI-63, "Diagnosis Procedure"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3.CHECK PARKING BRAKE SWITCH UNIT
Perform a unit check for the parking brake switch. Refer to MWI-63, "Component Inspection"
.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-82, "Removal and Installation".
NO >> Replace parking brake switch. Refer to PB-7, "Exploded View"
.
Condition Warning lamp status
Parking brake applied ON
Parking brake released OFF
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM