service NISSAN TEANA 2014 Service Manual

PWC-3
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
MAIN POWER WINDOW AND DOOR LOCK/
UNLOCK SWITCH ......................................... ....
65
Removal and Installation .........................................65
POWER WINDOW AND DOOR LOCK/UN-
LOCK SWITCH RH ........................................ ....
66
Removal and Installation .........................................66
REAR POWER WINDOW SWITCH ............... ....67
Removal and Installation .........................................67
LH & RH FRONT ANTI-PINCH
PRECAUTION ................ ..............................
68
PRECAUTIONS .............................................. ....68
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
68
Precaution for Work ................................................68
PREPARATION ...........................................69
PREPARATION .............................................. ....69
Special Service Tool ........................................... ....69
SYSTEM DESCRIPTION .............................70
COMPONENT PARTS ................................... ....70
Component Parts Location ................................ ....70
Component Description ...........................................70
SYSTEM .............................................................72
System Diagram ................................................. ....72
System Description .................................................72
Fail-safe ..................................................................74
DIAGNOSIS SYSTEM (BCM) ............................75
COMMON ITEM ..................................................... ....75
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) ................................................. ....
75
RETAINED PWR ................................................... ....76
RETAINED PWR : CONSULT Function (BCM -
RETAINED PWR) ............................................... ....
76
ECU DIAGNOSIS INFORMATION ..............77
BCM (BODY CONTROL MODULE) ............... ....77
List of ECU Reference ........................................ ....77
POWER WINDOW MAIN SWITCH ....................78
Reference Value ................................................. ....78
Fail Safe .................................................................79
FRONT POWER WINDOW SWITCH .................81
Reference Value ................................................. ....81
Fail Safe .................................................................82
WIRING DIAGRAM ......................................83
POWER WINDOW SYSTEM .......................... ....83
Wiring Diagram - With Left And Right Front Power
Window Anti-Pinch .............................................. ....
83
BASIC INSPECTION ...................................91
DIAGNOSIS AND REPAIR WORKFLOW ........91
Work Flow ............................................................ ....91
INSPECTION AND ADJUSTMENT ..................93
ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL ............................... ....
93
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Description . ....
93
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Special Re-
pair Requirement ................................................. ....
93
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT .................................................... ....
93
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ............................. ....
93
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .. ....
93
DTC/CIRCUIT DIAGNOSIS .........................95
POWER SUPPLY AND GROUND CIRCUIT ....95
BCM ....................................................................... ....95
BCM : Diagnosis Procedure ....................................95
POWER WINDOW MAIN SWITCH ........................ ....95
POWER WINDOW MAIN SWITCH : Description ....95
POWER WINDOW MAIN SWITCH : Component
Function Check .................................................... ....
96
POWER WINDOW MAIN SWITCH : Diagnosis
Procedure ............................................................ ....
96
POWER WINDOW MAIN SWITCH : Component
Inspection ............................................................ ....
98
POWER WINDOW MAIN SWITCH : Special Re-
pair Requirement ................................................. ....
99
FRONT POWER WINDOW SWITCH ..................... ....99
FRONT POWER WINDOW SWITCH : Descrip-
tion ....................................................................... ....
99
FRONT POWER WINDOW SWITCH : Compo-
nent Function Check ............................................ ..
100
FRONT POWER WINDOW SWITCH : Diagnosis
Procedure ............................................................ ..
100
FRONT POWER WINDOW SWITCH : Special
Repair Requirement ............................................ ..
101
REAR POWER WINDOW SWITCH ....................... ..101
REAR POWER WINDOW SWITCH : Description ..101
REAR POWER WINDOW SWITCH : Component
Function Check .................................................... ..
101
REAR POWER WINDOW SWITCH : Diagnosis
Procedure ............................................................ ..
101
REAR POWER WINDOW SWITCH : Component
Inspection ............................................................ ..
103
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-6
< PRECAUTION >[LH FRONT ONLY ANTI-PINCH]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint Syst
em (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951561
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for WorkINFOID:0000000009460817
• When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a s hop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PREPARATIONPWC-7
< PREPARATION > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
PREPARATION
PREPARATION
Special Service ToolINFOID:0000000009460818
The actual shapes of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name Description
—
(J-46534)
Trim Tool Set Removing trim components
AWJIA0483ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

INSPECTION AND ADJUSTMENTPWC-27
< BASIC INSPECTION > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVI NG BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription
INFOID:0000000009460830
Initial setting is necessary when battery terminal is disconnected.
CAUTION:
The following specified operations are not pe rformed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
• Retained power operation
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement
INFOID:0000000009460831
INITIALIZATION PROCEDURE
1. Disconnect battery minus terminal or power window ma in switch connector. Reconnect it after a minute or
more.
2. Turn ignition switch ON.
3. Operate power window switch to fully open the wi ndow. (This operation is unnecessary if the window is
already fully open)
4. Continue pulling the power window switch UP (AUTO-UP operation). Even after glass stops at fully closed
position, keep pulling the switch for 4 seconds or more.
5. Inspect anti-pinch function.
CHECK ANTI-PINCH FUNCTION
1. Fully open the door window.
2. Place a piece of wood near fully closed position.
3. Close door glass completely with AUTO-UP.
• Check that glass lowers for approximately 150 mm or 2 seconds without pinching piece of wood and stops.
• Check that glass does not rise when operating the power window main switch while lowering.
CAUTION:
• Do not check with hands and other part of body because they may be pinched. Do not get pinched.
• Check that AUTO-UP operates before inspectio n when system initialization is performed.
• It may switch to fail-safe mode if open/close oper ation is performed continuously. Perform initial set-
ting in that situ ation. Refer to PWC-11, "Fail-safe"
.
• Perform initial setting when auto-up operation or anti-pinch function does not operate normally.
• Finish initial setting. Otherwise, next operation cannot be done.
1. Auto-up operation
2. Anti-pinch function
3. Retained power operation wh en ignition switch is OFF.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPL ACING CONTROL UNIT : Description
INFOID:0000000009460832
Initial setting is necessary when replacing power window main switch.
CAUTION:
The following specified operations are not pe rformed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
• Retained power operation
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000009460833
INITIALIZATION PROCEDURE
1. Disconnect battery minus terminal or power window ma in switch connector. Reconnect it after a minute or
more.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER SUPPLY AND GROUND CIRCUITPWC-31
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
3. Check continuity between main power window and door lock/unlock switch connector D8 and ground.
Is the inspection result normal?
YES >> Check main power window and door lock/unlock switch output signal (rear power window switch
LH) GO TO 5.
YES >> Check main power window and door lock/unlock switch output signal (rear power window switch
RH) GO TO 6.
YES >> Check main power window and door lock/unlock s witch output signal (front power window switch
LH) GO TO 7.
YES >> Check main power window and door lock/unlock s witch output signal (front power window switch
RH) GO TO 8.
NO >> Repair or replace the harness or connectors.
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M21 and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace BCM. Refer to BCS-80, "Removal and Installation"
.
5. CHECK MAIN POWER WINDOW AND DOOR LOCK /UNLOCK SWITCH OUTPUT SIGNAL (REAR POW-
ER WINDOW SWITCH LH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch D12 and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
6. CHECK MAIN POWER WINDOW AND DOOR LOCK /UNLOCK SWITCH OUTPUT SIGNAL (REAR POW-
ER WINDOW SWITCH RH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch D12 and ground.
Main power window and door lock/unlock switch connector Terminal GroundContinuity
D8 1 Yes
Te r m i n a l s Vo l ta g e
(Approx.)
(+)
(–)
BCM connector Terminal
M21 140
Ground Battery voltage
141
Te r m i n a l
Window switch
position (rear LH) Vol tag e
(Approx.)
(+)
(–)
Main power window and door lock/
unlock switch connector Te r m i n a l
D12 8
Ground UP Battery voltage
DOWN 0
9 UP 0
DOWN Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-32
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
POWER SUPPLY AND GROUND CIRCUIT
Is the inspection result normal?
YES >> Check intermittent incident. Refer to
GI-43, "Intermittent Incident".
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
7. CHECK MAIN POWER WINDOW AND DOOR LO CK/UNLOCK SWITCH OUTPUT SIGNAL (FRONT
POWER WINDOW SWITCH LH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch D8 and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
8. CHECK MAIN POWER WINDOW AND DOOR LO CK/UNLOCK SWITCH OUTPUT SIGNAL (FRONT
POWER WINDOW SWITCH RH)
1. Connect main power window and door lock/unlock switch.
2. Turn ignition switch ON.
3. Check voltage between main power window and door lock/unlock switch D12 and ground.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
Te r m i n a l
Window switch
position (rear RH) Vo l ta g e
(Approx.)
(+)
(–)
Main power window and door
lock/unlock switch connector Te r m i n a l
D12 6
Ground UP Battery voltage
DOWN 0
7 UP 0
DOWN Battery voltage
Te r m i n a l Window switch
position (front LH) Vo l ta g e
(Approx.)
(+)
(–)
Main power window and door lock/
unlock switch connector Te r m i n a l
D8 17
Ground UP Battery voltage
DOWN 0
19 UP 0
DOWN Battery voltage
Te r m i n a l Window switch
position (front RH) Vo l ta g e
(Approx.)
(+)
(–)
Main power window and door
lock/unlock switch connector Te r m i n a l
D12 2
Ground UP Battery voltage
DOWN 0
16 UP 0
DOWN Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER SUPPLY AND GROUND CIRCUITPWC-33
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
POWER WINDOW MAIN SWIT CH : Component InspectionINFOID:0000000009460838
1. CHECK MAIN POWER WINDOW A ND DOOR LOCK/UNLOCK SWITCH
1. Check main power window and door lock/unlock switch D12.
2. Check continuity between main power window and door lock/unlock switch D12 (power window lock switch) (Lock operation).
3. Check continuity between main power window and door lock/unlock switch D12 (power window lock switch) (Unlock operation).
Terminal Main power window and door lock/unlock switch condition Continuity
10 8 Rear LH UP
Ye s
10 6 Rear RH
10 2 Front RH 8 9 Rear LH NEUTRAL
6 7 Rear RH
216 Front RH
10 9 Rear LH DOWN
10 7 Rear RH
10 16 Front RH 112 -
Terminal Main power window and door lock/unlock switch condition Continuity
9
1 Rear LH
UP
No
7Rear RH
16 Front RH 8 Rear LH
NEUTRAL
9
7 Rear RH
6
2 Front RH
16
8 Rear LH DOWN
6Rear RH
2Front RH
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-34
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
POWER SUPPLY AND GROUND CIRCUIT
Is the inspection result normal?
YES >> Main power window and door lock/unlock switch is OK.
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL
UNIT : Special Repair Requirement".
POWER WINDOW MAIN SWITCH : S pecial Repair RequirementINFOID:0000000009460839
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
ment".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check intermittent incident. Refer to GI-43, "Intermittent Incident"
.
2. CHECK ANTI-PINCH OPERATION
Check anti-pinch operation.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
ment".
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to PWC-30, "POWER WINDO W MAIN SWITCH : Component Function Check"
.
FRONT POWER WINDOW SWITCH
FRONT POWER WINDOW SWITCH : DescriptionINFOID:0000000009460840
• BCM supplies power.
• Front power window motor RH will be operated if power window and door lock/unlock switch RH is operated.
FRONT POWER WINDOW SWITCH : Component Function CheckINFOID:0000000009460841
Power Window And Door Lock/unlock Switch RH
1. CHECK POWER WINDOW MOTOR FUNCTION
Check front power window motor operation with power window and door lock/unlock switch RH.
Is the inspection result normal?
YES >> Power window and door lock/unlock switch RH power supply and ground circuit are OK.
NO >> Refer to PWC-35, "FRONT POWER WINDOW SWITCH : Diagnosis Procedure"
.
Terminal Main power window and door lock/unlock switch condition Continuity
9
1 Rear LH
UP
Ye s
7Rear RH
16 Front RH 8 Rear LH
NEUTRAL
9
7 Rear RH
6
2 Front RH
16
8Rear LH DOWN
6Rear RH
2Front RH
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER WINDOW MOTORPWC-41
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-41, "DRIVER SIDE : Special Repair Requirement".
NO >> Repair or replace harness.
3. CHECK FRONT POWER WINDOW MOTOR LH
Check front power window motor LH.
Refer to PWC-41, "DRIVER SIDE : Component Inspection"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace front power window motor LH. Refer to GW-16, "Removal and Installation - Front Regula-
tor". After that, refer to PWC-41, "DRIVER SIDE : Special Repair Requirement".
DRIVER SIDE : Component InspectionINFOID:0000000009460851
COMPONENT INSPECTION
1.CHECK FRONT POWER WINDOW MOTOR LH
Check motor operation by connecting the battery voltage directly to power window motor D9.
Is the inspection result normal?
YES >> Front power window motor LH is OK.
NO >> Replace front power window motor LH. Refer to GW-16, "Removal and Installation - Front Regula-
tor". After that, refer to PWC-41, "DRIVER SIDE : Special Repair Requirement".
DRIVER SIDE : Special Repair RequirementINFOID:0000000009460852
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special
Repair Requirement".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check intermittent incident. Refer to GI-43, "Intermittent Incident"
.
2. CHECK ANTI-PINCH OPERATION
Check anti-pinch operation.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special
Repair Requirement".
Is the inspection result normal?
YES >> Inspection end.
NO >> Refer to PWC-40, "DRIVER SIDE : Component Function Check"
.
PASSENGER SIDE
Main power window and door lock/un-
lock switch connector Te r m i n a l
GroundContinuity
D8 17
No
19
Te r m i n a l Motor condition
(+) (–)
31 DOWN
13 UP
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ENCODERPWC-49
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
2. Check continuity between main power window D12 and door lock/unlock switch connector and front
power window motor LH connector D9.
3. Check continuity between main power window and door lock/unlock switch connector and ground.
Is the inspection result normal?
YES >> Replace front power window motor LH. Refer to GW-16, "Removal and Installation - Front Regula-
tor". After that, refer to PWC-49, "DRIVER SIDE : Special Repair Requirement".
NO >> Repair or replace harness or connectors.
DRIVER SIDE : Special Repair RequirementINFOID:0000000009460868
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACIN G CONTROL UNIT : Special Repair Require-
ment".
Is the inspection result normal?
YES >> Inspection end.
NO >> Check intermittent incident. Refer to GI-43, "Intermittent Incident"
.
Main power window and door lock/unlock
switch connector Te r m i n a lFront power window motor
LH connector Terminal Continuity
D12 4
D9 6
Ye s
55
Main power window and door lock/unlock switch connector Te r m i n a l
GroundContinuity
D12 4
No
5
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM