brake sensor NISSAN TEANA 2014 Workshop Manual

EC-12
Diagnosis Procedure .............................................865
P0462, P0463 FUEL LEVEL SENSOR ...........866
DTC Logic ............................................................ ..866
Diagnosis Procedure .............................................866
P0500 VSS .......................................................867
Description ........................................................... ..867
DTC Logic ..............................................................867
Diagnosis Procedure .............................................867
P0506 ISC SYSTEM ........................................869
Description ........................................................... ..869
DTC Logic ..............................................................869
Diagnosis Procedure .............................................869
P0507 ISC SYSTEM ........................................871
Description ........................................................... ..871
DTC Logic ..............................................................871
Diagnosis Procedure .............................................871
P050A, P050E COLD START CONTROL .......873
Description ........................................................... ..873
DTC Logic ..............................................................873
Diagnosis Procedure .............................................874
P0520 EOP SENSOR ......................................875
DTC Logic ............................................................ ..875
Diagnosis Procedure .............................................875
Component Inspection ...........................................877
P0524 ENGINE OIL PRESSURE ....................878
DTC Logic ............................................................ ..878
Diagnosis Procedure .............................................879
Component Inspection ...........................................880
P0603 ECM POWER SUPPLY ........................881
DTC Logic ............................................................ ..881
Diagnosis Procedure .............................................881
P0605 ECM ......................................................883
DTC Logic ............................................................ ..883
Diagnosis Procedure .............................................883
P0607 ECM ......................................................884
DTC Logic ............................................................ ..884
Diagnosis Procedure .............................................884
P0643 SENSOR POWER SUPPLY .................885
Description ........................................................... ..885
DTC Logic ..............................................................885
Diagnosis Procedure .............................................885
P0850 PNP SWITCH .......................................887
Description ........................................................... ..887
DTC Logic ..............................................................887
Component Function Check ..................................888
Diagnosis Procedure .............................................888
P1148, P1168 CLOSED LOOP CONTROL .....890
DTC Logic ............................................................ ..890
P1212 TCS COMMUNICATION LINE ..............891
Description ........................................................... .891
DTC Logic .............................................................891
Diagnosis Procedure .............................................891
P1217 ENGINE OVER TEMPERATURE .........892
DTC Logic ............................................................ .892
Component Function Check .................................892
Diagnosis Procedure .............................................893
P1225 TP SENSOR ..........................................895
DTC Logic ............................................................ .895
Diagnosis Procedure .............................................895
P1226 TP SENSOR ..........................................896
DTC Logic ............................................................ .896
Diagnosis Procedure .............................................896
P1550 BATTERY CURRENT SENSOR ...........897
DTC Logic ............................................................ .897
Diagnosis Procedure .............................................897
Component Inspection ..........................................898
P1551, P1552 BATTERY CURRENT SEN-
SOR ................................................................ ..
899
DTC Logic ............................................................ .899
Diagnosis Procedure .............................................899
Component Inspection ..........................................900
P1553 BATTERY CURRENT SENSOR ...........901
DTC Logic ............................................................ .901
Diagnosis Procedure .............................................901
Component Inspection ..........................................902
P1554 BATTERY CURRENT SENSOR ...........903
DTC Logic ............................................................ .903
Component Function Check .................................903
Diagnosis Procedure .............................................903
Component Inspection ..........................................904
P1556, P1557 BATTERY TEMPERATURE
SENSOR ......................................................... ..
906
DTC Logic ............................................................ .906
Diagnosis Procedure .............................................906
Component Inspection (Battery Temperature
Sensor) ................................................................ .
907
P1564 ASCD STEERING SWITCH ..................908
DTC Logic ............................................................ .908
Diagnosis Procedure .............................................908
Component Inspection ..........................................910
P1572 ASCD BRAKE SWITCH ........................911
Description ........................................................... .911
DTC Logic .............................................................911
Component Function Check .................................912
Diagnosis Procedure .............................................913
Component Inspection (Brake Pedal Position
Switch) ................................................................. .
916
Component Inspection (Stop Lamp Switch) ..........916
Component Inspection (Stop Lamp Relay) ...........917
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-13
C
D E
F
G H
I
J
K L
M
EC A
N
O P
P1574 ASCD VEHICLE SPEED SENSOR .... ..918
Description .......................................................... ..918
DTC Logic .............................................................918
Diagnosis Procedure .............................................918
P1800 VIAS CONTROL SOLENOID VALVE 1 ..920
DTC Logic ........................................................... ..920
Diagnosis Procedure .............................................920
Component Inspection ..........................................921
P1801 VIAS CONTROL SOLENOID VALVE 2 ..922
DTC Logic ........................................................... ..922
Diagnosis Procedure .............................................922
Component Inspection ..........................................923
P1805 BRAKE SWITCH ................................. ..924
Description .......................................................... ..924
DTC Logic .............................................................924
Diagnosis Procedure .............................................924
Component Inspection (Stop Lamp Switch) ..........926
Component Inspection (Stop Lamp Relay) ...........926
P2096, P2097, P2098, P2099 A/F SENSOR 1 ..927
DTC Logic ........................................................... ..927
Diagnosis Procedure .............................................927
P2100, P2103 THROTTLE CONTROL MO-
TOR RELAY ................................................... ..
931
DTC Logic ........................................................... ..931
Diagnosis Procedure .............................................931
P2101 ELECTRIC THROTTLE CONTROL
FUNCTION ..................................................... ..
933
DTC Logic ........................................................... ..933
Diagnosis Procedure .............................................933
Component Inspection ..........................................935
P2118 THROTTLE CONTROL MOTOR ..........936
DTC Logic ........................................................... ..936
Diagnosis Procedure .............................................936
Component Inspection ..........................................937
P2119 ELECTRIC THROTTLE CONTROL
ACTUATOR .................................................... ..
938
DTC Logic ........................................................... ..938
Diagnosis Procedure .............................................938
P2122, P2123 APP SENSOR ...........................940
DTC Logic ........................................................... ..940
Diagnosis Procedure .............................................940
Component Inspection ..........................................941
P2127, P2128 APP SENSOR ...........................942
DTC Logic ........................................................... ..942
Diagnosis Procedure .............................................942
Component Inspection ..........................................943
P2135 TP SENSOR ..........................................945
DTC Logic ........................................................... ..945
Diagnosis Procedure .............................................945
Component Inspection ..........................................946
P2138 APP SENSOR ......................................947
DTC Logic ............................................................ ..947
Diagnosis Procedure .............................................947
Component Inspection ...........................................949
BRAKE PEDAL POSITION SWITCH .............950
Component Function Check ..................................950
Diagnosis Procedure .............................................950
Component Inspection (Brake Pedal Position
Switch) ................................................................. ..
951
ASCD INDICATOR ..........................................952
Component Function Check ..................................952
Diagnosis Procedure .............................................952
COOLING FAN ................................................953
Component Function Check ..................................953
Diagnosis Procedure .............................................953
Component Inspection (Cooling Fan Motor) ..........955
Component Inspection (Cooling Fan Relay) ..........956
ELECTRICAL LOAD SIGNAL ........................957
Description .............................................................957
Component Function Check ..................................957
Diagnosis Procedure .............................................957
ELECTRONIC CONTROLLED ENGINE
MOUNT ............................................................
959
Component Function Check ................................ ..959
Diagnosis Procedure .............................................959
Component Inspection ...........................................960
FUEL INJECTOR ............................................962
Component Function Check ..................................962
Diagnosis Procedure .............................................962
Component Inspection ...........................................963
FUEL PUMP ....................................................965
Component Function Check ..................................965
Diagnosis Procedure .............................................965
Component Inspection ...........................................966
IGNITION SIGNAL ..........................................967
Component Function Check ..................................967
Diagnosis Procedure .............................................967
Component Inspection (Ignition Coil with Power
Transistor) ........................................................... ..
970
Component Inspection (Condenser) ......................971
INFORMATION DISPLAY (ASCD) .................972
Component Function Check ..................................972
Diagnosis Procedure .............................................972
MALFUNCTION INDICATOR LAMP ..............973
Component Function Check ..................................973
Diagnosis Procedure .............................................973
ON BOARD REFUELING VAPOR RECOV-
ERY (ORVR) ....................................................
974
Component Function Check ................................ ..974
Diagnosis Procedure .............................................974
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-24
< SYSTEM DESCRIPTION >[QR25DE]
COMPONENT PARTS
A. Instrument panel area B. Periphery of pedals C. Inside fuel tank area
D. Behind fuel tank
: Vehicle front
No. Component Function Combination meter Malfunction indicator lamp (MIL)
EC-36, "Malfunction Indicator lamp (MIL)"
Information displayEC-37, "Information Display"
ASCD steering switch EC-37, "ASCD Steering Switch"
Stop lamp switch
EC-36, "Stop Lamp Switch & Brake Pedal Position Switch"
Brake pedal position switch
Accelerator pedal position sensor EC-25, "Accelerator Pedal Position Sensor"
Fuel level sensor unit and fuel pumpEC-26, "Fuel Level Sensor Unit and Fuel Pump"
Fuel tank temperature sensorEC-27, "Fuel Tank Temperature Sensor"
EVAP control system pressure sensorEC-35, "EVAP Control System Pressure Sensor"
EVAP canister vent control valve EC-35, "EVAP Canister Vent Control Valve"
EVAP canisterEC-34, "EVAP Canister"
ALBIA0806ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-36
< SYSTEM DESCRIPTION >[QR25DE]
COMPONENT PARTS
Battery temperature sensor is int
egrated in battery current sensor.
The sensor measures temperature around the battery.
The electrical resistance of the t hermistor decreases as temperature
increases.

*: These data are reference values and are measured between battery temperature
sensor signal terminal and sensor ground.
Malfunction Indicator lamp (MIL)INFOID:0000000009462083
The Malfunction Indicator lamp (MIL) is located on the combination
meter.
The MIL will illuminate when the ignition switch is turned ON without
the engine running. This is a bulb check.
When the engine is started, the MI L should turn OFF. If the MIL
remains illuminated, the on board diagnostic system has detected an
engine system malfunction.
For details, refer to EC-74, "DIAGNOSIS DESCRIPTION : Malfunc-
tion Indicator Lamp (MIL)".
Oil Pressure Warning LampINFOID:0000000009462084
Oil pressure warning lamp is located on the combination meter.
It indicates the low pressure of the engine oil and the malfunction of
the engine oil pressure system.
Combination meter turns the oil pressure warning lamp ON/OFF
according to the oil pressure warning lamp signal received from
ECM via CAN communication.
For details, refer to EC-55, "ENGINE PROTECTION CONTROL AT
LOW ENGINE OIL PRESSURE : System Description".
Refrigerant Pressure SensorINFOID:0000000009462085
The refrigerant pressure sensor is installed at the c ondenser of the air conditioner system. The sensor uses an
electrostatic volume pressure transducer to convert refrigerant pressure to voltage. The voltage signal is sent
to ECM, and ECM controls cooling fan system.
Stop Lamp Switch & Brake Pedal Position SwitchINFOID:0000000009462086
Stop lamp switch and brake pedal position switch are installed to brake pedal bracket.
ECM detects the state of the brake pedal by those two types of input (ON/OFF signal).
Temperature [°C ( °F)]
Vo l ta g e* (V) Resistance (k
Ω)
25 (77) 3.333 1.9 - 2.1
90 (194) 0.969 0.222 - 0.258
SEF012P
JSBIA1315ZZ
PBIA8559J
PBIB2657E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SYSTEMEC-43
< SYSTEM DESCRIPTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
MULTIPORT FUEL INJECTION SYSTEM
MULTIPORT FUEL INJECTION SYSTEM : S
ystem Description (with automatic air
P052A
P052B Intake valve timing intermedi-
ate lock control ——
× —
P0603 ECM power supply circuit — ×——
P0605 ECM — ×——
P0643 Sensor power supply ———ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P1078 Exhaust valve timing control position sensor circuit ×
— × —
P1805 Brake switch
———ECM controls the electric throttle control actuator by regulat-
ing the throttle opening to a small range.
Therefore, acceleration will be poor.
Vehicle condition Driving condition
When engine is idling Normal When accelerating Poor acceleration
P2004 Intake manifold runner control valve —
×× —
P2100
P2103 Throttle contro
l motor relay
——— ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P2101 Electric throttle control func- tion ——— ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P2118 Throttle control motor ———ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P2119 Electric thro ttle control actua-
tor —
×——
P2122
P2123
P2127
P2128
P2138 Accelerator pedal position
sensor
———The ECM controls the electric throttle control actuator in reg-
ulating the throttle opening in order for the idle position to be
within +10 degrees.
The ECM regulates the opening speed of the throttle valve to
be slower than the normal condition.
So, the acceleration will be poor.
DTC
No. Detected items Vehicle behavior
Pattern Others
ABC
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-80
< SYSTEM DESCRIPTION >[QR25DE]
DIAGNOSIS SYSTEM (ECM)
TP SEN 1-B1
V××
• The throttle position sensor signal volt-age is displayed. • TP SEN 2-B1 signal is convert-
ed by ECM internally. Thus, it
differs from ECM terminal volt-
age signal.
TP SEN 2-B1
××
FUEL T/TMP SE °C or °F • The fuel temperature (determined by the
signal voltage of the fuel tank tempera-
ture sensor) is displayed.
EVAP SYS PRES V • The signal voltage of EVAP control sys-
tem pressure sensor is displayed.
FUEL LEVEL SE V ו The signal voltage of the fuel level sensor
is displayed.
START SIGNAL On/Off • Indicates start signal status [ON/OFF]
computed by the ECM according to the
signals of engine speed and battery volt-
age. • After starting the engine, [OFF]
is displayed regardless of the
starter signal.
CLSD THL POS On/Off ×ו Indicates idle position [ON/OFF] comput-
ed by ECM according to the accelerator
pedal position sensor signal.
AIR COND SIG On/Off ×ו Indicates [ON/OFF] condition of the air
conditioner switch as determined by the
air conditioner signal.
PW/ST SIGNAL On/Off ×ו [ON/OFF] condition of the power steering
system (determined by the signal sent
from EPS control unit) is indicated.
LOAD SIGNAL On/Off ×ו Indicates [ON/OFF] condition from the
electrical load signal.
- On: Rear window defogger switch is ON and/or lighting switch is in 2nd position.
- Off: Both rear window defogger switch
and lighting switch are OFF.
IGNITION SW On/Off ×ו Indicates [ON/OFF] condition from igni-
tion switch signal.
HEATER FAN SW On/Off ו Indicates [ON/OFF] condition from the
heater fan switch signal.
BRAKE SW On/Off • Indicates [ON/OFF] condition from the
stop lamp switch signal.
INJ PULSE-B1 msec • Indicates the actual fuel injection pulse
width compensated by ECM according to
the input signals. • When the engine is stopped, a
certain computed value is indi-
cated.
IGN TIMING BTDC ו Indicates the ignition timing computed by
ECM according to the input signals. • When the engine is stopped, a
certain value is indicated.
CAL/LD VALUE % • “Calculated load value” indicates the val-
ue of the current air flow divided by peak
air flow.
MASS AIRFLOW g/s • Indicates the mass air flow computed by
ECM according to the signal voltage of
the mass air flow sensor.
Monitored item Unit
Monitor Item
Selection
Description Remarks
ECU
IN-
PUT
SIG-
NALS MAIN
SIG-
NAL S
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-82
< SYSTEM DESCRIPTION >[QR25DE]
DIAGNOSIS SYSTEM (ECM)
ALT DUTY SIG On/Off• The control condition of the power gener-
ation voltage variable control (deter-
mined by ECM according to the input
signals) is indicated.
- On: Power generation voltage variable control is active.
- Off: Power generation voltage variable control is inactive.
I/P PULLY SPD rpm • Indicates the engine speed computed
from the input speed sensor signal.
VEHICLE SPEED km/h or mph • The vehicle speed computed from the
vehicle speed signal sent from TCM is
displayed.
IDL A/V LEARN YET/CMPLT • Displays the condition of Idle Air Volume
Learning
- YET: Idle air volume learning has not been performed yet.
- CMPLT: Idle air volume learning has al-
ready been performed successfully.
TRVL AFTER MIL km or mile • Distance traveled while MIL is activated.
ENG OIL TEMP °C or °F • The engine oil temperature (determined
by the signal voltage of the engine oil
temperature sensor) is displayed.
A/F S1 HTR(B1) % • Air fuel ratio (A/F) sensor 1 heater control
value computed by ECM according to the
input signals.
• The current flow to the heater becomes
larger as the value increases.
VHCL SPEED SE km/h or mph • The vehicle speed computed from the
vehicle speed signal sent from combina-
tion meter is displayed.
SET VHCL SPD km/h or mph • The preset vehicle speed is displayed.
MAIN SW On/Off • Indicates [ON/OFF] condition from MAIN
switch signal.
CANCEL SW On/Off • Indicates [ON/OFF] condition from CAN-
CEL switch signal.
RESUME/ACC SW On/Off • Indicates [ON/OFF] condition from RE-
SUME/ACCELERATE switch signal.
SET SW On/Off • Indicates [ON/OFF] condition from SET/
COAST switch signal.
BRAKE SW1 On/Off • Indicates [ON/OFF] condition from brake
pedal position switch signal.
BRAKE SW2 On/Off • Indicates [ON/OFF] condition of stop
lamp switch signal.
VHCL SPD CUT Non/Cut • Indicates the vehicle cruise condition.
- Non: Vehicle speed is maintained at the
ASCD set speed.
- Cut: Vehicle speed decreased to exces- sively low compared with the ASCD set
speed, and ASCD operation is cut off.
Monitored item Unit
Monitor Item
Selection
Description Remarks
ECU
IN-
PUT
SIG-
NALS MAIN
SIG-
NAL S
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-101
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
: Average voltage for pulse signal (Actual pulse signal can be confirmed by oscilloscope.)
*1: For California
*2: Before measuring the terminal voltage, confi rm that the battery is fully charged. Refer to PG-4, "How to
Handle Battery".
Fail SafeINFOID:0000000009462122
NON DTC RELATED ITEM
11 5
(L) 128
(GR) Stop lamp switch Input [Ignition switch: OFF]
• Brake pedal: Fully released 0 V
[Ignition switch: OFF]
• Brake pedal: Slightly depressed Battery voltage
(11 - 14 V)
11 6
(BR) 128
(GR) Brake pedal position
switch Input[Ignition switch: OFF]
• Brake pedal: Fully released Battery voltage
(11 - 14 V)
11 7
(W) 128
(GR) PNP signal Input [Ignition switch: ON]
• Selector lever: P or N Battery voltage
(11 - 14 V)
[Ignition switch: ON]
• Selector lever: Except above 0 V
11 8 (G) —Sensor power supply
(Accelerator pedal posi-
tion sensor 2) — [Ignition switch: ON] 5.0 V
11 9 (P) 120
(G) Accelerator pedal posi-
tion sensor 2 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released 0.25 - 0.5 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully depressed 2.0 - 2.5 V
120 (G) —Sensor ground
(Accelerator pedal posi-
tion sensor 2) —— —
121
(LG) 128
(GR) Power supply for ECM Input [Ignition switch: ON] Battery voltage
(11 - 14 V)
122 (V) —Sensor power supply
(Accelerator pedal posi-
tion sensor 1) — [Ignition switch: ON] 5.0 V
124
(SB) —Sensor ground
(EVAP control system
pressure sensor, refriger-
ant pressure sensor) —— —
125
(BR) 128
(GR) Fuel tank temperature
sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with fuel tank temperature
126
(SB) 127
(L) Accelerator pedal posi-
tion sensor 1 Input[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully released 0.5 - 1.0 V
[Ignition switch: ON]
• Engine stopped
• Accelerator pedal: Fully depressed 4.2 - 4.8 V
127 (L) —Sensor ground
(Accelerator pedal posi-
tion sensor 1) —— —
128
(GR) — ECM ground — — —
Terminal No.
(Wire color) Description
ConditionVa l u e
(Approx.)
+ − Signal name Input/
Output
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-103
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
OP0171
P0172 Fuel injection system
×—— —
P0197
P0198 Engine oil temperature sensor
———Exhaust valve timing control does not function.
P0300
P0301
P0302
P0303
P0304 Misfire
×—— —
P0500 Vehicle speed sensor ×—— —
P050A Cold start control ×—— —
P0524 Engine oil pressure
———• ECM illuminates oil pressure warning lamp on the combina-
tion meter.
• Engine speed will not rise more than 4,000rpm due to the fuel cut.
• Fail-safe is canceled when ignition switch OFF → ON.
P052A
P052B Intake valve timing intermedi-
ate lock control ——
× —
P0603 ECM power supply circuit — ×——
P0605 ECM — ×——
P0643 Sensor power supply ———ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P1078 Exhaust valve timing control position sensor circuit ×
— × —
P1805 Brake switch
———ECM controls the electric throttle control actuator by regulat-
ing the throttle opening to a small range.
Therefore, acceleration will be poor.
Vehicle condition Driving condition
When engine is idling Normal When accelerating Poor acceleration
P2004 Intake manifold runner control valve —
×× —
P2100
P2103 Throttle contro
l motor relay
——— ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P2101 Electric throttle control func- tion ——— ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P2118 Throttle control motor ———ECM stops the electric throttle control actuator control, throttle
valve is maintained at a fixed opening (approx. 5 degrees) by
the return spring.
P2119 Electric thro ttle control actua-
tor —
×——
P2122
P2123
P2127
P2128
P2138 Accelerator pedal position
sensor
———The ECM controls the electric throttle control actuator in reg-
ulating the throttle opening in order for the idle position to be
within +10 degrees.
The ECM regulates the opening speed of the throttle valve to
be slower than the normal condition.
So, the acceleration will be poor.
DTC
No. Detected items Vehicle behavior
Pattern Others
ABC
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-105
< ECU DIAGNOSIS INFORMATION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
DTC IndexINFOID:0000000009462124
×
:Applicable —: Not applicable
2 P0031, P0032 Air fuel ratio (A/F) sensor 1 heater
P0037, P0038 Heated oxygen sensor 2 heater
P0075 Intake valve timing control solenoid valve/Intake valve timing
intermediate lock control solenoid valve
P0078 Exhaust valve timing control solenoid valve
P0130, P0131, P0132, P014 C, P014D, P015A, P015B,
P117A, P2096, P2097 Air fuel ratio (A/F) sensor 1
P0137, P0138, P0139 Heated oxygen sensor 2
P0441 EVAP control system purge flow monitoring
P0443, P0444, P0445 EVAP canister purge volume control solenoid valve
P0447, P0448 EVAP canister vent control valve
P0451, P0452, P0453 EVAP control system pressure sensor
P1217 Engine over temperature (OVERHEAT)
P1800 Intake manifold tuning valve
P1805 Brake switch
P2004 Intake manifold runner control valve
P2100, P2103 Throttle control motor relay
P2101 Electric thrott le control function
P2118 Throttle control motor
3 P0011, P052A, P052B Intake valve timing control
P0014 Exhaust valve timing control
P0171, P0172 Fuel injection system function
P0300, P0301, P0302, P0303, P0304 Misfire
P0420 Three way catalyst function
P0456 EVAP control system
P0506, P0507 Idle speed control system
P050A, P050B, P050E Cold start control
P0524 Engine oil pressure
P1148 Closed loop control
P1212 TCS communication line
P1564 ASCD steering switch
P1572 ASCD brake switch
P1574 ASCD vehicle speed sensor
P1715 Input speed sensor
P2119 Electric throttle control actuator
Priority DTC Detected items
DTC*1
Items
(CONSULT screen terms) SRT
code Trip MIL Permanent
DTC group*4Reference page
CONSULT
GST
*2ECM*3
U0101 0101*5CAN COMM CIRCUIT — 1 ×BEC-207
U1001
1001*5CAN COMM CIRCUIT — 2 — — EC-208
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM