crank NISSAN TEANA 2014 Manual Online

SYSTEMEC-573
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
AIR CONDITIONING CUT CONTROL : System DescriptionINFOID:0000000009462517
SYSTEM DIAGRAM
*1: Automatic air conditioning system
*2: Manual air conditioning system
INPUT/OUTPUT SIGNAL CHART
*1: ECM determines the start signal status by the signals of engine speed and battery voltage.
*2: Automatic air conditioning system
*3: Manual air conditioning system
SYSTEM DESCRIPTION
This system improves engine operation when the air conditioner is used.
Under the following conditions, the air conditioner is turned OFF.
• When the accelerator pedal is fully depressed.
• When cranking the engine.
• At high engine speeds.
• When the engine coolant temperature becomes excessively high.
• When operating power steering during low engine speed or low vehicle speed.
JSBIA2685GB
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS) Engine speed
*1
Air conditioner
cut control IPDM E/R
↓
Air conditioner relay
↓
Compressor
Camshaft position sensor (PHASE)
Engine coolant temperature sensor Engine coolant temperature
Accelerator pedal position sensor Accelerator pedal position
Battery Battery voltage*1
Refrigerant pressure sensor Refrigerant pressure
Power steering control module EPS operation signal
CAN communi-
cation line
Combination meter Vehicle speed signal
A/C auto amp.
*2• A/C ON signal
• Blower fan ON signal
BCM
*3
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-576
< SYSTEM DESCRIPTION >[VQ35DE]
SYSTEM
Manual Air Conditioning System
INPUT/OUTPUT SIGNAL CHART
*1: The ECM determines the start signal status by the signals of engine speed and battery voltage.
*2: This signal is sent to ECM via the CAN communication line.
*3: Automatic air conditioning system
*4: Manual air conditioning system
SYSTEM DESCRIPTION
The ECM controls the cooling fan corresponding to the vehicle speed, engine coolant temperature, refrigerant
pressure, and air conditioner ON signal. The control system has 4-step control [HIGH/MIDDLE/LOW/OFF].
JSBIA0321GB
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE) Engine speed*
1
Piston position
Cooling fan
control IPDM E/R
↓
Cooling fan relay
↓
Cooling fan motor
Engine coolant temperature sensor Engine coolant temperature
Refrigerant pressure sensor Refrigerant pressure
Battery Battery voltage*
1
Combination meter
Vehicle speed signal*2
A/C auto amp.*3• A/C ON signal
• Blower fan ON signal
BCM
*4
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-578
< SYSTEM DESCRIPTION >[VQ35DE]
SYSTEM
*: This signal is sent to the ECM via the CAN communication line.
SYSTEM DESCRIPTION
The ECM controls the engine mount operation correspondi
ng to the engine speed. The control system has a
2-step control [Soft/Hard]
ELECTRONIC CONTROLLED ENGINE MOUNT LINE DRAWING
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE) Engine speed
Engine mount
control Electronic controlled en-
gine mount control solenoid
valve
Combination meter Vehicle speed*
Vehicle condition Engine mount control
Engine speed: Below 950 rpm Soft
Engine speed: Above 950 rpm Hard
JMBIA2161ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-580
< SYSTEM DESCRIPTION >[VQ35DE]
SYSTEM
EVAPORATIVE EMISSION SYSTEM : System Description
INFOID:0000000009462521
SYSTEM DIAGRAM
INPUT/OUTPUT SIGNAL CHART
*1: ECM determines the start signal status by the signals of engine speed and battery voltage.
*2: This signal is sent to the ECM via the CAN communication line.
JSBIA0371GB
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS) Engine speed*
1
Piston position
EVAP canister
purge flow control EVAP canister purge vol-
ume control solenoid valve
Camshaft position sensor (PHASE)
Mass air flow sensor Amount of intake air
Engine coolant temperature sensor Engine coolant temperature
Air fuel ratio (A/F) sensor 1 Density of oxygen in exhaust gas
(Mixture ratio fe edback signal)
Throttle position sensor Throttle position
Accelerator pedal position sensor Accelerator pedal position
Battery Battery voltage*
1
Fuel tank temperature sensor Fuel temperature in fuel tank
EVAP control system pressure sensor Pressure in purge line
Combination meter Vehicle speed*
2
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-582
< SYSTEM DESCRIPTION >[VQ35DE]
SYSTEM
Manual Air Conditioning System
INPUT/OUTPUT SIGNAL CHART
*1: ECM determines the start signal status
by the signals of engine speed and battery voltage.
*2: Automatic air conditioning system
*3: Manual air conditioning system
SYSTEM DESCRIPTION
ECM calculates the value of signal transmitted from t he accelerator pedal and activates the throttle valve by
transmitting a control signal to the electric throttle c ontrol actuator. This allows the optimum throttle angle and
improves drivability and fuel consumption. In addition, ECM learns the fully closed position every time when
the ignition switch is turned OFF to improv e the accuracy in throttle valve position.
When a malfunction occurs in the throttle control system , the throttle valve is closed by the return spring and
maintains the minimum engine speed by holding a slightly opened condition which is close to the fully opened
condition. This allows the securing of brake syste m, power steering system, and electric system and the
ensuring of the safety.
INTAKE VALVE TIMING CONTROL
JSBIA1917GB
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS) Engine speed
*1
Throttle controlElectric throttle control
actuator
Engine coolant temperature sensor Engine coolant temperature
Mass air flow sensor Amount of intake air
Intake air temperature sensor Intake air temperature
Accelerator pedal position sensor Accelerator pedal position
Ignition switch Start signal and ignition OFF
Combination meter CAN communi-
cation Vehicle speed signal
A/C auto amp.
*2CAN communi-
cation • A/C ON signal
• Blower fan ON signal
BCM
*3
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SYSTEMEC-583
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
INTAKE VALVE TIMING CONT
ROL : System DescriptionINFOID:0000000009462523
SYSTEM DIAGRAM
INPUT/OUTPUT SIGNAL CHART
*: This signal is sent to the ECM via the CAN communication line
SYSTEM DESCRIPTION
This mechanism hydraulically controls cam phases c ontinuously with the fixed operating angle of the intake
valve.
The ECM receives signals such as crankshaft posit ion, camshaft position, engine speed, and engine coolant
temperature. Then, the ECM sends ON/OFF pulse duty si gnals to the intake valve timing (IVT) control sole-
noid valve depending on driving status. This makes it po ssible to control the shut/open timing of the intake
valve to increase engine torque in low/mid speed range and output in high-speed range.
ENGINE PROTECTION CONTROL AT LOW ENGINE OIL PRESSURE
ENGINE PROTECTION CONTROL AT LOW ENGINE OIL PRESSURE : System De-
JPBIA4760GB
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS) Engine speed and piston position
Intake valve
timing control Intake valve timing control
solenoid valve
Camshaft position sensor (PHASE)
Engine oil temperature sensor Engine oil temperature
Engine coolant temperature sensor Engine coolant temperature
Combination meter Vehicle speed signal*
JMBIA0060GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-584
< SYSTEM DESCRIPTION >[VQ35DE]
SYSTEM
scription
INFOID:0000000009462524
SYSTEM DIAGRAM
INPUT/OUTPUT SIGNAL CHART
SYSTEM DESCRIPTION
• The engine protection control at low engine oil pressure warns the driver of a decrease in engine oil pres-
sure by the oil pressure warning lamp before the engine becomes damaged.
• When detecting a decrease in engine oil pressure at an engine speed less than 1,000 rpm, ECM transmits
an oil pressure warning lamp signal to the combination meter.The combination meter turns ON the oil pres-
sure warning lamp, according to the signal.
• When detecting a decrease in engine oil pressure at an engine speed 1,000 rpm or more, ECM transmits an
oil pressure warning lamp signal to the combination meter.
The combination meter turns ON the oil pressure warning lamp, according to the signals. When detecting a
decrease in engine oil pressure, ECM cuts fuel if the engine speed exceeds the specified value.
*: When detecting a normal engine oil pressure, ECM turns OFF the oil pressure warning lamp.
FUEL FILLER CAP WARNING SYSTEM
JSBIA1588GB
Sensor Input signal to ECM ECM function Actuator
Engine oil pressure sensor Engine oil pressure Engine protection control
• Oil pressure warning lamp
signal
• Fuel cut control Combination meter
(Oil pressure warning lamp)
Crankshaft position sensor
(POS) Engine speed
Engine oil temperature sensor Engine oil temperature
Decrease in engine oil pressure Engine speed Combination meter
Fuel cut
Oil pressure warning lamp
Detection Less than 1,000 rpm ON* NO
1,000 rpm or more ON YES
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-586
< SYSTEM DESCRIPTION >[VQ35DE]
SYSTEM
MIL turns ON if a malfunction is detected in leak diagnosis
results again at the trip after the fuel filler cap warn-
ing display turns ON/OFF.
VARIABLE INDUCTION AIR SYSTEM
VARIABLE INDUCTION AIR SYSTEM : System DescriptionINFOID:0000000009462526
SYSTEM DIAGRAM
INPUT/OUTPUT SIGNAL CHART
*: ECM determines the start signal status by the signals of engine speed and battery voltage.
SYSTEM DESCRIPTION
JMBIA1831GB
Sensor Input signal to ECM ECM function Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE) Engine speed*
VIAS controlVIAS control solenoid valve 1
VIAS control solenoid valve 2
Mass air flow sensor Amount of intake air
Engine coolant temperature sensor Engine coolant temperature
Throttle position sensor Throttle position
Accelerator pedal position sensor Accelerator pedal position
Battery Battery voltage*
JMBIA0181GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DIAGNOSIS SYSTEM (ECM)EC-603
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
×
: Applicable
Monitored item Unit Monitor Item Selec-
tion
Description Remarks
ECU IN-
PUT SIG- NALS MAIN-
SIG-
NALS
ENG SPEED rpm ××Indicates the engine speed comput-
ed from the signal of the crankshaft
position sensor (POS) and camshaft
position sensor (PHASE). • Accuracy becomes poor if engine
speed drops below the idle rpm.
• If the signal is interrupted while the engine is running, an abnor-
mal value may be indicated.
MAS A/F SE-B1 V ××The signal voltage of the mass air
flow sensor is displayed. • When the engine is stopped, a
certain value is indicated.
• When engine is running, specifi- cation range is indicated in
“SPEC”.
B/FUEL SCHDL ms ×דBase fuel schedule” indicates the
fuel injection pulse width pro-
grammed into ECM, prior to any
learned on board correction. • When engine is running, specifi-
cation range is indicated in
“SPEC”.
A/F ALPHA-B1
% The mean value of the air-fuel ratio
feedback correction factor per cycle
is indicated. • When the engine is stopped, a
certain value is indicated.
• This data also includes the data
for the air-fuel ratio learning con-
trol.
• When engine is running, specifi-
cation range is indicated in
“SPEC”.
A/F ALPHA-B2
COOLAN TEMP/S °C or °F ×× The engine coolant temperature (de-
termined by the signal voltage of the
engine coolant temperature sensor)
is displayed. When the engine coolant tempera-
ture sensor is open or short-circuit-
ed, ECM enters fail-safe mode. The
engine coolant temperature deter-
mined by the ECM is displayed.
A/F SEN1 (B1) V××
The A/F signal computed from the
input signal of the air fuel ratio (A/F)
sensor 1 is displayed.
A/F SEN1 (B2)
××
HO2S2 (B1) V××
The signal voltage of the heated ox-
ygen sensor 2 is displayed.
HO2S2 (B2) ××
HO2S2 MNTR(B1)
RICH/LEAN ×
Display of heated oxygen sensor 2
signal:
• RICH: means the amount of oxy-
gen after three way catalyst is rel-
atively small.
• LEAN: means the amount of oxy-
gen after three way catalyst is rel-
atively large. When the engine is stopped, a cer-
tain value is indicated.
HO2S2 MNTR(B2) ×
VHCL SPEED SE km/h or
mph ×× The vehicle speed computed from
the vehicle speed signal sent from
combination meter is displayed.
BATTERY VOLT V The power supply voltage of ECM is
displayed.
ACCEL SEN 1 V The accelerator pedal position sen-
sor signal voltage is displayed. ACCEL SEN 2 signal is converted
by ECM internally. Thus, it differs
from ECM terminal voltage signal.
ACCEL SEN 2
TP SEN 1-B1 V××
The throttle position sensor signal
voltage is displayed. TP SEN 2-B1 signal is converted by
ECM internally. Thus, it differs from
ECM terminal voltage signal.
TP SEN 2-B1
××
FUEL T/TMP SE °C or °F The fuel temperature (determined by
the signal voltage of the fuel tank
temperature sensor) is displayed.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-610
< SYSTEM DESCRIPTION >[VQ35DE]
DIAGNOSIS SYSTEM (ECM)
*: This function is not necessary in the usual service procedure.
ACTIVE TEST MODE
Test Item
WORK ITEM CONDITION USAGE
IDLE AIR VOL LEARN The idle air volume that keeps the engine within the specified range is memorized in ecm. When learning the idle air volume
EVAP SYSTEM CLOSE Close the EVAP canister vent control valve in order to make
EVAP system close under the following conditions.
• Ignition switch ON
• Engine not running
• Ambient temperature is above 0 °C (32 °F).
• No vacuum and no high pressure in EVAP system
• Fuel tank temperature is more than 0 °C (32 °F).
• Within 10 minutes after starting “EVAP SYSTEM CLOSE”
• When trying to execute “EVAP SYSTEM CLOSE” under
the condition except above, CONSULT will discontinue it
and display appropriate instruction.
NOTE:
When starting engine, CONSULT may display “BAT-
TERY VOLTAGE IS LOW. CHARGE BATTERY”, even in
using charged battery. When detecting EVAP vapor leak-
age in the EVAP system
FUEL PRESSURE RELEASE Fuel pu mp will stop by touching “START” during idling.
crank a few times after engine stalls. When releasing fuel pressure from
fuel line
SELF-LEARNING CONT The coefficient of self-learning control mixture ratio returns to the original coefficient. When clearing mixture ratio self-
learning value
TARGET IGN TIM ADJ* Idle condition When adjusting target ignition tim- ing
TARGET IDLE RPM ADJ* Idle condition When setting target idle speed
VIN REGISTRATION In this mode, VIN is registered in ECM When registering VIN in ECM
CLSD THL POS LEARN Ignition on and engine stopped. When learning the throttle valve
closed position
SAVING DATA FOR REPLC CPU In this mode, save data that is in ECM. When ECM replaced.
WRITING DATA FOR REPLC CPU In this mode, write data stored by “SAVING DATA FOR RE-
PLC CPU” in work support mode to ECM. When ECM replaced.
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
FUEL INJEC-
TION • Engine: Return to the original
non-standard condition
• Change the amount of fuel injec- tion using CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. • Harness and connectors
• Fuel injector
• Air fuel ratio (A/F) sensor 1
ENG COOLANT
TEMP • Engine: Return to the original
non-standard condition
• Change the engine coolant tem- perature using CONSULT. If malfunctioning symptom disap-
pears, see CHECK ITEM. • Harness and connectors
• Engine coolant temperature sen-
sor
• Fuel injector
PURG VOL
CONT/V • Engine: After warming up, run en-
gine at 1,500 rpm.
• Change the EVAP canister purge volume control solenoid valve
opening percent using CON-
SULT. Engine speed changes according to
the opening percent. • Harness and connectors
• Solenoid valve
FUEL/T TEMP
SEN • Change the fuel tank temperature using CONSULT.
ALTERNATOR
DUTY •Engine: Idle
• Change duty ratio using CON-
SULT. Battery voltage changes.
• Harness and connectors
• IPDM E/R
•Alternator
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM