NISSAN TERRANO 2004 Service Repair Manual

YBT079
WINDSHIELD AND WINDOWS
Removal and Installation (Cont'd)BT-44
http://vnx.su/

*1 BT-46*2 BT-21
YBT080
WINDSHIELD AND WINDOWS
Removal and Installation (Cont'd)
BT-45
http://vnx.su/

DRYING TIME FOR SEALANT
IReference: Time required for sealant to dry to desired hardness.
CAUTION:
Advise the user of the fact that vehicle should not be driven on rough roads or surfaces until sealant
has properly vulcanized.
Unit: days
Relative humidity
%
Temperature ÉC (ÉF) Windshield and Rear window
Back door window
90 5025905025
40 (104) 1.52.55.01.52.55.5
25 (77) 2.54.07.52.54.58.5
5 (41) 5.0 13.0 20.5 5.5 14.0 22.0
REPAIRING WATER LEAKS FOR WINDSHIELD
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and
body or glass, determine the extent of leakage. This can be
done by applying water to the windshield area while pushing
glass outward.
To stop the leak, apply primer (if necessary) and then urethane
adhesive to the leak point.
SBF543B
WINDSHIELD AND WINDOWS
Removal and Installation (Cont'd)
BT-46
http://vnx.su/

BACK DOOR WINDOW
IWindow glass is held in place by weatherstrip. Refer to
ªEXTERIORº, BT-21.
I Apply sealer to clearances between vehicle body panel and
weatherstrip as necessary.
EBF030
WINDSHIELD AND WINDOWS
Removal and Installation (Cont'd)
BT-47
http://vnx.su/

Removal and Installation
CAUTION:
Be careful not to scratch door rearview mirror body.
HFor Wiring Diagram, refer to EL-275, ªDOOR MIRRORº for details.
1. Remove door trim. Refer to ªDOOR TRIMº, BT-19.
2. Remove inner cover front corner of door.
3. Disconnect door mirror harness connector.
4. Remove harness clips.
5. Remove bolts securing door mirror assembly.
YBT135
DOOR MIRROR
BT-48
http://vnx.su/

Alignment
IAll dimensions indicated in figures are actual ones.
I When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge
itself to make sure there is no free play.
I When a measuring tape is used, check to be sure there is no elongation, twisting or bending.
I Measurements should be taken at the center of the mounting holes.
I An asterisk (*) following the value at the measuring point indicates that the measuring point on the other
side is symmetrically the same value.
I The coordinates of the measurement points are the distances measured from the standard line of ªXº, ªYº
and ªZº.
YBT089
BODY (ALIGNMENT)
BT-49
http://vnx.su/

ENGINE COMPARTMENT
Measurement
Unit: mm (in)
NBF021
BODY (ALIGNMENT)
Alignment (Cont'd)BT-50
http://vnx.su/

Detailed Measurement Points
PointsHole dia.
mm (in) Detailed points Coordinates mm (in)
ªXº ªYº ªZº
q
A8 (0.32)
NBF022
Cowl top hole at
vehicle center 0.0
(0.00) 250.0
(9.84) 760.9
(29.96)
q
Bqb11 (0.43)
NBF023
Cowl top side
hole 698.5
(27.50) þ110.1
(þ4.34) 624.7
(24.59)
q
Dqd8 (0.32)
NBF024
Upper radiator
core support
location hole 691.0
(27.20) þ459.5
(þ18.09) 548.0
(21.58)
q
Hqh16 (0.63) Side radiator
core support
location hole680.0
(26.77) þ551.7
(þ21.72) 400.0
(15.75)
q
1: Coordinate indicated isLH,RHcoordinate is -LHcoordinate.
E.g. ifLHcoordinate is: 698.5,RHcoordinate is: þ698.5.
BODY (ALIGNMENT)
Alignment (Cont'd)
BT-51
http://vnx.su/

PointsHole dia.
mm (in) Detailed points Coordinates mm (in)
ªXº ªYº ªZº
q
E9 (0.35)
NBF025
Hood lock stay
mounting hole
on upper radia-
tor core support 37.0
(1.46) þ589.0
(þ23.19) 494.0
(19.45)
q
I
Lower radiator
core support
mounting hole 0.0
(0.00) þ581.1
(þ22.88) þ54.1
(þ2.13)
q
Gqg12 (0.47) Lower radiator
core support
location hole280.0
(11.02) þ608.9
(þ23.97) þ23.0
(þ0.91)
q
Cqc7.2 (0.28)
NBF027
Front fender
mounting hole
on hoodledge 698.5
(27.50) þ110.1
(þ4.34) 624.7
(24.59)
q
1: Coordinate indicated isLH,RHcoordinate is -LHcoordinate.
E.g. ifLHcoordinate is: 698.5,RHcoordinate is: þ698.5.
BODY (ALIGNMENT)
Alignment (Cont'd)
BT-52
http://vnx.su/

UNDERBODY
Measurement (Hardtop model)
NBF028
BODY (ALIGNMENT)
Alignment (Cont'd)BT-53
http://vnx.su/