ad blue NISSAN TIIDA 2007 Service Owner's Manual

DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)
DLK-55
< FUNCTION DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
*1: The item is only for M/T model.INDICATORThis test is able to check warning lamp operation.
 BLUE ON: Key warning lamp (green) illuminates.
 RED ON: Key warning lamp (red) illuminates.
 KNOB ON: Lock warning lamp illuminates.
 BLUE IND: Key warning lamp (green) flashes.
 RED IND: Key warning lamp (red) flashes.
 KNOB IND: Lock warning lamp flashes.
OFF
KEY LOCK SOLENOID
*1This test is able to check key interlock operation.
 LOCK: Key interlock is active.
 UNLOCK: Key interlock is inactive. Test item Description

DLK-146
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
KEY WARNING LAMP
KEY WARNING LAMP
DescriptionINFOID:0000000001396621
Performs operation method guide and warning together with buzzer.
Component Function CheckINFOID:0000000001396622
1.CHECK FUNCTION
With CONSULT-III
Check the operation with “INDICATOR” in “Active Test” mode.
Is the inspection result normal?
Yes >> Key warning lamp in combination meter is OK.
No >> Refer to DLK-146, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001396623
1.CHECK KEY WARNING LAMP CIRCUIT
Refer to XX-XX, "*****"
.
Is the inspection result normal?
Ye s > > G O T O 2 .
No >> Repair or replace key warning lamp circuit.
2.CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
Test item Condition
INDICATOR:BLUE ON Key warning lamp (green) illuminates
:RED ON Key warning lamp (red) illuminates
:BLUE IND Key warning lamp (green) flashes
:RED IND Key warning lamp (red) flashes

DLK-280
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DIAGNOSIS SYSTEM (INTELLIGENT KEY UNIT)
*1: The item is only for M/T model.INDICATORThis test is able to check warning lamp operation.
BLUE ON: Key warning lamp (green) illuminates.
 RED ON: Key warning lamp (red) illuminates.
 KNOB ON: Lock warning lamp illuminates.
 BLUE IND: Key warning lamp (green) flashes.
 RED IND: Key warning lamp (red) flashes.
 KNOB IND: Lock warning lamp flashes.
OFF
KEY LOCK SOLENOID
*1This test is able to check key interlock operation.
 LOCK: Key interlock is active.
 UNLOCK: Key interlock is inactive. Test item Description

DLK-376
< COMPONENT DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
KEY WARNING LAMP
KEY WARNING LAMP
DescriptionINFOID:0000000001530369
Performs operation method guide and warning together with buzzer.
Component Function CheckINFOID:0000000001530370
1.CHECK FUNCTION
With CONSULT-III
Check the operation with “INDICATOR” in “Active Test” mode.
Is the inspection result normal?
Yes >> Key warning lamp in combination meter is OK.
No >> Refer to DLK-376, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000001530371
1.CHECK KEY WARNING LAMP CIRCUIT
Refer to XX-XX, "*****"
.
Is the inspection result normal?
Ye s > > G O T O 2 .
No >> Repair or replace key warning lamp circuit.
2.CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
Test item Condition
INDICATOR:BLUE ON Key warning lamp (green) illuminates
:RED ON Key warning lamp (red) illuminates
:BLUE IND Key warning lamp (green) flashes
:RED IND Key warning lamp (red) flashes

EC-17
C
D
E
F
G
H
I
J
K
L
M
ECA
N
O
P Description ..........................................................
1265
Diagnosis Procedure ...........................................1265
NO OR VERY LITTLE ACCELERATION, IN-
CREASE IN ENGINE SPEED ........................
1267
Description ..........................................................1267
Diagnosis Procedure ...........................................1267
ENGINE BUCKING ........................................1270
Description ..........................................................1270
Diagnosis Procedure ...........................................1270
ERRATIC ACCELERATION ..........................1272
Description ..........................................................1272
Diagnosis Procedure ...........................................1272
NO ENGINE BRAKING ..................................1274
Description ..........................................................1274
Diagnosis Procedure ...........................................1274
LOSS OF POWER ..........................................1275
Description ..........................................................1275
Diagnosis Procedure ...........................................1275
TOO MUCH POWER ......................................1278
Description ..........................................................1278
Diagnosis Procedure ...........................................1278
OVERSPEED AT IDLE SPEED OR ON RE-
LEASING BRAKE ..........................................
1280
Description ..........................................................1280
Diagnosis Procedure ...........................................1280
EXCESSIVE CONSUMPTION ........................1281
Description ..........................................................1281
Diagnosis Procedure ...........................................1281
ENGINE KNOCK ............................................1283
Description ..........................................................1283
Diagnosis Procedure ...........................................1283
ENGINE OVERHEATING ...............................1285
Description ...........................................................1285
Diagnosis Procedure ...........................................1285
ENGINE SMOKES WHEN STARTED ...........1286
Description ...........................................................1286
Diagnosis Procedure ...........................................1286
ENGINE EMITS BLUE SMOKE .....................1287
Description ...........................................................1287
Diagnosis Procedure ...........................................1287
ENGINE SMOKES WHEN REVVED ..............1289
Description ...........................................................1289
Diagnosis Procedure ...........................................1289
ENGINE EMITS WHITE SMOKE (ESPECIAL-
LY WHEN STARTING) ...................................
1290
Description ...........................................................1290
Diagnosis Procedure ...........................................1290
EMISSION CONTROL NOT SATISFACTORY 1291
Description ...........................................................1291
Diagnosis Procedure ...........................................1291
PRECAUTION ...........................................1293
PRECAUTIONS ..............................................1293
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................
1293
Precaution for Procedure without Cowl Top Cover 1293
On Board Diagnostic (OBD) System of Engine ...1293
General Precautions ............................................1294
Cleanliness ..........................................................1296
SERVICE DATA AND SPECIFICATIONS
(SDS) .........................................................
1298
SERVICE DATA AND SPECIFICATIONS
(SDS) ..............................................................
1298
Idle Speed ...........................................................1298

ENGINE CONTROL SYSTEM SYMPTOMS
EC-1255
< SYMPTOM DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
SYMPTOM DIAGNOSIS
ENGINE CONTROL SYSTEM SYMPTOMS
Symptom TableINFOID:0000000001162698
NOTE:
Only consult this customer complaint after a complete check using the CONSULT-III.
Symptom Trouble diagnosis Reference page
No communication with the ECM CHART 1EC-1256, "
Diag-
nosis Procedure"
Starting malfunctionEngine does not start or starts with difficulty CHART 2EC-1257, "
Diag-
nosis Procedure"
Starting difficult with cold engine CHART 3EC-1259, "Diag-
nosis Procedure"
Impossible to shut off engine CHART 4EC-1261, "Diag-
nosis Procedure"
Idle speed malfunctionEngine Idle speed too high CHART 5EC-1262, "
Diag-
nosis Procedure"
Engine Idle speed too low or unstable CHART 6EC-1263, "Diag-
nosis Procedure"
Behavior while drivingEngine stalling CHART 7EC-1265, "
Diag-
nosis Procedure"
No or very little acceleration, increase in engine speed CHART 8EC-1267, "Diag-
nosis Procedure"
Engine bucking CHART 9EC-1270, "Diag-
nosis Procedure"
Erratic acceleration CHART 10EC-1272, "Diag-
nosis Procedure"
No engine braking CHART 11EC-1274, "Diag-
nosis Procedure"
Loss of power CHART 12EC-1275, "Diag-
nosis Procedure"
Too much power CHART 13EC-1278, "Diag-
nosis Procedure"
Overspeed at idle speed or on releasing brake CHART 14EC-1280, "Diag-
nosis Procedure"
Excessive consumption CHART 15EC-1281, "Diag-
nosis Procedure"
Engine knock CHART 16EC-1283, "Diag-
nosis Procedure"
Engine overheating CHART 17EC-1285, "Diag-
nosis Procedure"
Noise, odors or smokeEngine smokes when started CHART 18EC-1286, "
Diag-
nosis Procedure"
Engine emits blue smoke CHART 19EC-1287, "Diag-
nosis Procedure"
Engine smokes when revved CHART 20EC-1289, "Diag-
nosis Procedure"
Engine emits white smoke (especially when starting) CHART 21EC-1290, "Diag-
nosis Procedure"
Emission control not satisfactory CHART 22EC-1291, "Diag-
nosis Procedure"

ENGINE EMITS BLUE SMOKE
EC-1287
< SYMPTOM DIAGNOSIS >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
EC
N
P O
ENGINE EMITS BLUE SMOKE
DescriptionINFOID:0000000001162735
CHART 19: ENGINE EMITS BLUE SMOKE
Diagnosis ProcedureINFOID:0000000001162736
1.CHECK ENGINE OIL
Check the grade of engine oil. Refer to LU-26, "
Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace engine oil. Refer to LU-27, "
Refilling"
2.CHECK ENGINE OIL LEVEL
Is the engine oil level correct?
Ye s o r N o
Yes >> GO TO 3.
No >> Top up the oil.
3.CHECK FUEL
Check that the fuel reservoir is correctly filled and with the right fuel.
>> GO TO 4.
4.CHECK ENGINE COOLANT TEMPERATURE SENSOR
Check engine coolant temperature sensor. Refer to EC-1133, "
Component Inspection".
Is the inspection result normal?
Yes >> GO TO 5.
No >> Repair or replace.
5.CHECK AIR INTAKE SYSTEM
Check air intake system. Refer to EM-269, "
Removal and Installation".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace air intake system.
6.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR
Check electric throttle control actuator. Refer to EC-1134, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair or replace.
7.CHECK MASS AIR FLOW SENSOR
Check mass air flow sensor. Refer to EC-1125, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 8.
NO >> Repair or replace.
8.CHECK TURBOCHARGER
Check that the turbocharger is working properly. Refer to EC-1195, "
Diagnosis Procedure".
Is the turbocharger correct?
Yes >> GO TO 9.
No >> Repair or replace.
9.CHECK EGR SYSTEM
Check EGR system. Refer to EC-1202, "
Diagnosis Procedure".

EC-1288
< SYMPTOM DIAGNOSIS >[K9K]
ENGINE EMITS BLUE SMOKE
Is the inspection result normal?
YES >> GO TO 10.
NO >> Repair or replace.
10.CHECK CATALYTIC CONVERTER
Is the catalytic converter clogged or deteriorated?
Is the inspection result normal?
YES >> GO TO 11.
NO >> Repair or replace.
11 .CHECK HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE)
Perform the TEST 3: HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE). Refer to EC-1044,
"BASIC INSPECTION : Special Repair Requirement [TEST 3: High Pressure Supply Pump (Pressure Control
Valve) Check]".
>> GO TO 12.
12.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)
Perform the TEST 4: HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE). Refer to EC-
1045, "BASIC INSPECTION : Special Repair Requirement [TEST 4: High Pressure Supply Pump (Volumetric
Control Valve) Check]".
>> GO TO 13.
13.CHECK RAIL HIGH PRESSURE CONTROL CIRCUIT
Perform the TEST 5: RAIL HIGH PRESSURE CONTROL CIRCUIT CHECK. Refer to EC-1048, "
BASIC
INSPECTION : Special Repair Requirement (TEST 5: Rail High Pressure Regulation Check)".
>> GO TO 14.
14.CHECK MAJOR LEAK IN FUEL INJECTOR/FUEL INJECTORS OPEN
Perform the TEST 6: MAJOR LEAK IN FUEL INJECTOR/FUEL INJECTORS OPEN. Refer to EC-1052,
"BASIC INSPECTION : Special Repair Requirement (TEST 6: Major Leak in Fuel Injectors/Fuel Injectors
Open)".
>> GO TO 15.
15.CHECK INCORRECT FUEL INJECTION QUANTITY
Perform the TEST 7: INCORRECT FUEL INJECTION QUANTITY. Refer to EC-1053, "
BASIC INSPECTION :
Special Repair Requirement (TEST 7: Incorrect Fuel Injection Quantity)".
>> GO TO 16.
16.CHECK ECM POWER SUPPLY AND GROUND CIRCUIT
Check ECM power supply and ground circuit. Refer to EC-1106, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 17.
NO >> Repair or replace harness or connector.
17.CHECK WIRING HARNESS
Visually check the condition of the engine wiring harness.
Is the inspection result normal?
YES >>INSPECTION END
NO >> Repair or replace harness or connector.

EM-54
< ON-VEHICLE REPAIR >[HR16DE]
TIMING CHAIN
The illustration shows the relationship between the matching mark
on each timing chain and that on the corresponding sprocket, with
the components installed.
1. Install the crankshaft sprocket and the oil pump drive related parts with the following procedure:
a. Install the crankshaft sprocket (1), the oil pump drive chain (2),
and the oil pump sprocket (3) at the same time.
 Install the crankshaft sprocket so that its invalid gear area (A)
is towards the back of the engine.
 Install the oil pump sprocket so that its hexagonal surface
faces (B) the front of engine.
NOTE:
There is no matching mark in the oil pump drive related parts.
b. Hold the top of the oil pump shaft using the TORX socket (size:
E8), and then tighten the oil pump sprocket nuts.
1 : Timing chain
2 : Camshaft sprocket (EXH)
3 : Timing chain slack guide
4 : Chain tensioner
5 : Oil pump drive chain
6 : Oil pump sprocket
7 : Crankshaft sprocket
8 : Timing chain tension guide
9 : Camshaft sprocket (INT)
A : Dark blue link
B : Matching mark (stamp)
C : Orange link
D : Matching mark (stamp)
E : Crankshaft key (point straight up)
F : Matching mark (peripheral stamp line)
G : Dark blue link
PBIC3718E
: Engine front
PBIC3719E
1 : Crankshaft sprocket
2 : Oil pump drive chain
3 : Oil pump sprocket
PBIC3720E

TIMING CHAIN
EM-55
< ON-VEHICLE REPAIR >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
EM
N
P O
c. Install chain tensioner (1).
 Insert the body into the shaft (B) while inserting the spring into
the fixing hole (A) of cylinder block front surface.
 Make sure that the tension is applied to the oil pump drive
chain after installing.
2. Install timing chain with the following procedure.
 Install by aligning matching marks on each sprocket and tim-
ing chain.
 If these matching marks are not aligned, rotate the camshaft
slightly to correct the position.
CAUTION:
 Check matching mark position of each sprocket and tim-
ing chain again after installing the timing chain, keep
matching marks aligned by holding them with a hand.
 To avoid skipped teeth, never rotate crankshaft and cam-
shaft until front cover is installed.
3. Install timing chain tension guide (2) and timing chain slack
guide (1).
4. Install chain tensioner (1).
 Fix the plunger at the most compressed position using a stop-
per pin (A), and then install it.
 Securely pull out the stopper pin after installing the chain ten-
sioner.
PBIC3716E
A : Dark blue link
B : Matching mark (stamp)
C : Orange link
D : Matching mark (stamp)
E : Crankshaft key (point straight up)
F : Matching mark (peripheral stamp line)
G : Dark blue link
PBIC3721E
PBIC3714E
PBIC3722E