reverse light NISSAN TIIDA 2007 Service Owner's Guide

TM-570
< DISASSEMBLY AND ASSEMBLY >[TYPE 2 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
3. Install spring retainer assembly (1) on low & reverse brake pis-
ton (2).
4. Set Tool on spring retainer assembly, and install snap ring while
compressing spring retainer assembly.
CAUTION:
Set Tool directly over return springs.
5. Install driven plates (4), dish plates (6), retaining plates (2), (5)
and drive plates (3).
(1): Snap ring
(2): Retaining plate
(3): Drive plate
(4): Driven plate
(5): Retaining plate
(6): Dish plate
Drive plate/Driven plate: 4/4
CAUTION:
Be careful with the order of plates
NOTE:
Install two dish plates fitting each installation direction with
groove (1) and (2) displaced slightly.
SCIA6020J
SAT242D
SCIA5994E
SAT254E

TM-650
< DISASSEMBLY AND ASSEMBLY >[5MT: RS5F91R]
TRANSAXLE ASSEMBLY
27. Shift the shift lever (1) of control shaft assembly to 3rd gear posi-
tion.
NOTE:
 If not, the transaxle case cannot be removed from clutch hous-
ing.
 3rd gear position means that the shift lever of control shaft
assembly is fully rotated clockwise and it is returned approxi-
mately 10°.
28. Install oil gutter to transaxle case.
29. Apply recommended sealant to mating surface of clutch hous-
ing.
CAUTION:
 Remove old sealant adhering to the mating surfaces. Also remove any moisture, oil, or foreign
material adhering to both mating surfaces.
 Check for damage on the mounting surface.
 Apply a continuous bead of liquid gasket to the mounting surface.
30. Install transaxle case to clutch housing.
(1): Selector
(2): Shift fork
CAUTION:
 Do not allow sealant to contact the transaxle case so as
not to break the bead when installing.
 Be careful to align the lever of 5th-reverse fork rod with
reverse gear assembly sleeve.
NOTE:
If installation is difficult, gently return shift lever of control shaft
assembly counterclockwise slightly.
31. Fit shaft with bearing by rotating input shaft. Then, tighten bolts
to the specified torque. Refer to TM-635, "
Exploded View".
32. Apply recommended sealant to threads of position switch and
check ball plug. Then install them to transaxle case and tighten
to the specified torque. Refer to TM-635, "
Exploded View".
33. Apply gear oil to spline of mainshaft and then press in 5th main
gear (1) to mainshaft using a suitable bolt (A) [M10 x 1.0] and
nut (B).
34. Install spread springs to 5th-reverse synchronizer hub.
PCIB1524E
PCIB1553E
PCIB1528E
PCIB1554E

WCS-64
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
13
(V)GroundCombination switch
OUTPUT 1OutputCombination
switchAll switch OFF
(Wiper intermittent dial 4)0V
Front wiper switch HI
(Wiper intermittent dial 4)
Rear wiper switch INT
(Wiper intermittent dial 4)
Any of the condition below
with all switch OFF
 Wiper intermittent dial 1
 Wiper intermittent dial 2
 Wiper intermittent dial 3
 Wiper intermittent dial 6
 Wiper intermittent dial 7
14
(L)GroundCombination switch
OUTPUT 3OutputCombination
switch
(Wiper intermit-
tent dial 4)All switch OFF 0V
Lighting switch AUTO
Rear fog lamp switch OFF
Front wiper switch MIST
Front wiper switch INT
Front wiper switch LO
15
(BR)GroundCombination switch
OUTPUT 5OutputCombination
switch
(Wiper intermit-
tent dial 4)All switch OFF 0V
Lighting switch 1ST
Lighting switch 2ND
Lighting switch HI
Turn signal switch RH
16
(R)Ground Stop lamp switch InputDepress the brake pedal Battery voltage
Release the brake pedal 0V
17
(Y)Ground Back up lamp signal InputShift lever in reverse Battery voltage
Other than above 0V
19
(L)—CAN-HInput/
Output——
21
(BR)GroundRoom lamp timer
controlOutputInterior room
lampOFF Battery voltage
ON 0V
22
(P)GroundBattery power sup-
plyInput — Battery voltage
23
1
(LG)Ground Rear wiper auto stop OutputIgnition switch
ONRear wiper stop position 0V
Any position other than
rear wiper stop position Te r m i n a l N o .
(Wire color)Description
ConditionReference Value
(Approx.)
Signal nameInput/
Output +−
SKIA2167J
SKIA2167J
SKIA2167J
JPMIA0197GB