oil filter NISSAN TIIDA 2007 Service Service Manual

LU-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION LU
A
LU
N
O
P
CONTENTS
ENGINE LUBRICATION SYSTEM
HR16DE
FUNCTION DIAGNOSIS ...............................
3
DESCRIPTION ....................................................3
Engine Lubrication System .......................................3
Engine Lubrication System Schematic ......................3
PRECAUTION ...............................................4
PRECAUTIONS ...................................................4
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................
4
Liquid Gasket ............................................................4
PREPARATION ............................................5
PREPARATION ...................................................5
Special Service Tools ................................................5
Commercial Service Tools ........................................5
ON-VEHICLE MAINTENANCE .....................6
ENGINE OIL ........................................................6
Inspection ..................................................................6
Draining .....................................................................7
Refilling .....................................................................8
OIL FILTER .........................................................9
Removal and Installation ...........................................9
Inspection ..................................................................9
SERVICE DATA AND SPECIFICATIONS
(SDS) ............................................................
10
SERVICE DATA AND SPECIFICATIONS
(SDS) ..................................................................
10
Periodical Maintenance Specification .....................10
Engine Oil Pressure ................................................10
MR18DEFUNCTION DIAGNOSIS ..............................
11
LUBRICATION SYSTEM ..................................11
Lubrication Circuit ....................................................11
PRECAUTION ..............................................12
PRECAUTIONS .................................................12
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
12
Precaution for Liquid Gasket ...................................12
PREPARATION ...........................................13
PREPARATION .................................................13
Special Service Tool ................................................13
Commercial Service Tool ........................................13
ON-VEHICLE MAINTENANCE ....................15
ENGINE OIL ......................................................15
Inspection ................................................................15
Changing Engine Oil ................................................16
OIL FILTER .......................................................18
Removal and Installation .........................................18
ON-VEHICLE REPAIR .................................19
OIL COOLER ....................................................19
Components ............................................................19
Removal and Installation .........................................19
OIL PUMP .........................................................20
Components ............................................................20
Removal and Installation .........................................20
SERVICE DATA AND SPECIFICATIONS
(SDS) ............................................................
22
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................
22

LU-2
Standard and Limit .................................................22
K9K
PRECAUTION .............................................
23
PRECAUTIONS .................................................23
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................
23
Precaution for Liquid Gasket ..................................23
PREPARATION ...........................................25
PREPARATION .................................................25
Special Service Tools .............................................25
Commercial Service Tools ......................................25
ON-VEHICLE MAINTENANCE ...................26
ENGINE OIL .......................................................26
Inspection ...............................................................26
Draining ..................................................................27
Refilling ...................................................................27
OIL FILTER ........................................................28
Replacement ...........................................................28
ON-VEHICLE REPAIR ...............................29
OIL FILTER BRACKET .....................................29
Exploded View ........................................................29
Removal and Installation .........................................29
OIL COOLER .....................................................30
Exploded View ........................................................30
Removal and Installation .........................................30
Inspection ................................................................31
OIL PUMP ..........................................................32
Exploded View ........................................................32
Removal and Installation .........................................32
SERVICE DATA AND SPECIFICATIONS
(SDS) ..........................................................
33
SERVICE DATA AND SPECIFICATIONS
(SDS) .................................................................
33
Periodical Maintenance Specification ....................33
Engine Oil Pressure ..............................................33

PREPARATION
LU-5
< PREPARATION >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
LU
N
P O
PREPARATION
PREPARATION
Special Service ToolsINFOID:0000000001381525
Commercial Service ToolsINFOID:0000000001381526
Tool number
Tool nameDescription
ST25051001
Oil pressure gaugeMeasuring oil pressure
Maximum measuring range:
2,452 kPa (24.52 bar, 25 kg-cm
2, 356 psi)
ST25052000
HoseAdapting oil pressure gauge to cylinder block
KV10115801
Oil filter wrenchRemoving and installing oil filter
a: 64.3 mm (2.531 in)
NT050
S-NT559
S-NT375
Tool nameDescription
Deep socketRemoving and installing oil pressure switch
a: 27 mm (1.06 in)
PBIC4066E

LU-6
< ON-VEHICLE MAINTENANCE >[HR16DE]
ENGINE OIL
ON-VEHICLE MAINTENANCE
ENGINE OIL
InspectionINFOID:0000000001381527
ENGINE OIL LEVEL
NOTE:
Before starting engine, put vehicle horizontally and check the engine oil level. If engine is already started, stop
it and allow 10 minutes before checking.
1. Pull out oil level gauge and wipe it clean.
2. Insert oil level gauge and make sure the engine oil level is within
the range (A) shown in the figure.
3. If it is out of range, adjust it.
ENGINE OIL APPEARANCE
 Check engine oil for white turbidity or heavy contamination.
 If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following area.
 Oil pan (upper and lower)
 Oil pan drain plug
 Oil pressure switch
 Oil level sensor
 Oil filter
 Intake valve timing control solenoid valve
 Front cover
 Mating surface between cylinder head and camshaft bracket
 Mating surface between cylinder block and cylinder head
 Mating surface between cylinder head and rocker cover
 Crankshaft oil seals (front and rear)
 Oil filter (for intake valve timing control)
OIL PRESSURE CHECK
WARNING:
 Be careful not to get burned, as engine oil may be hot.
 When checking engine oil pressure, shift position should be “Neutral”, and apply parking brake
securely.
1. Check engine oil level. Refer to LU-6, "
Inspection".
JPBIA0554ZZ

LU-8
< ON-VEHICLE MAINTENANCE >[HR16DE]
ENGINE OIL
Refilling
INFOID:0000000001381529
1. Install drain plug with new washer. Refer to EM-100, "Exploded View".
CAUTION:
Be sure to clean drain plug and install with new washer.
2. Refill with new engine oil.
Engine oil specification and viscosity: Refer to MA-19, "
Fluids and Lubricants".
CAUTION:
 The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
 Always use oil level gauge to determine the proper amount of engine oil in the engine.
3. Warm up engine and check area around drain plug and oil filter for engine oil leakage.
4. Stop engine and wait for 10 minutes.
5. Check the engine oil level. Refer to LU-6, "
Inspection". Drain plug : Refer to EM-100, "
Exploded View".

OIL FILTER
LU-9
< ON-VEHICLE MAINTENANCE >[HR16DE]
C
D
E
F
G
H
I
J
K
L
MA
LU
N
P O
OIL FILTER
Removal and InstallationINFOID:0000000001381530
REMOVAL
 Using oil filter wrench [SST: KV10115801] (A), remove oil filter.
CAUTION:
 Oil filter is provided with relief valve. Use Genuine NISSAN
Oil Filter or equivalent.
 Be careful not to get burned when engine and engine oil
may be hot.
 When removing, prepare a shop cloth to absorb any engine
oil leakage or spillage.
 Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3. Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.
InspectionINFOID:0000000001381531
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to LU-6, "Inspection".
2. Start the engine, and check there is no leak of engine oil.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level, and adjust the level. Refer to LU-6, "
Inspection".
: Vehicle font
PBIC3818E
SMA010
Oil filter : 17.7 N·m (1.8 kg-m, 13 ft-lb)
SMA229B

LU-10
< SERVICE DATA AND SPECIFICATIONS (SDS) [HR16DE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance SpecificationINFOID:0000000001381532
ENGINE OIL CAPACITY (APPROXIMATE)
Unit: (lmp qt)
Engine Oil PressureINFOID:0000000001381533
*: Engine oil temperature at 80°C (176°F)
Drain and refill With oil filter change 4.3 (3-3/4)
Without oil filter change 4.1 (3-5/8)
Dry engine (Overhaul)4.8 (4-1/4)
Engine speed (rpm)
Approximate discharge pressure* [kPa (bar, kg/cm2, psi)]
Idle speed More than 60 (0.60, 0.61, 9)
2,000 More than 270 (2.7, 2.8, 39)

PREPARATION
LU-13
< PREPARATION >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
LU
N
P O
PREPARATION
PREPARATION
Special Service ToolINFOID:0000000001337824
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service ToolINFOID:0000000001337825
Tool number
(Kent-Moore No.)
Tool nameDescription
ST25051001
(J-25695-1)
Oil pressure gaugeMeasuring oil pressure
Maximum measuring range: 2,452 kPa (25
kg/cm
2, 356 psi)
ST25052000
(J-25695-2)
HoseAdapting oil pressure gauge to oil pan (upper)
KV10115801
(J-38956)
Oil filter wrenchRemoving oil filter
a: 64.3 mm (2.531 in)
WS39930000
(—)
Tube presserPressing the tube of liquid gasket
NT050
S-NT559
S-NT375
NT052

ENGINE OIL
LU-15
< ON-VEHICLE MAINTENANCE >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
LU
N
P O
ON-VEHICLE MAINTENANCE
ENGINE OIL
InspectionINFOID:0000000001337827
ENGINE OIL LEVEL
NOTE:
Before starting engine, park vehicle on a level surface and check the engine oil level. If engine is already
started, stop it and allow 10 minutes before checking.
1. Pull out oil level gauge and wipe it clean.
2. Insert oil level gauge and make sure the engine oil level is within
the range (A) as shown.
3. If it is out of range, adjust it.
ENGINE OIL APPEARANCE
 Check engine oil for white turbidity or heavy contamination.
 If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following areas:
 Oil pan (upper and lower)
 Oil pan drain plug
 Oil pressure switch
 Oil filter
 Intake valve timing control solenoid valve
 Front cover
 Mating surface between cylinder block and cylinder head
 Mating surface between cylinder head and rocker cover
 Crankshaft oil seals (front and rear)
 Oil filter (for intake valve timing control)
OIL PRESSURE CHECK
WARNING:
 Be careful not to burn yourself, as engine oil may be hot.
 For engine oil pressure check the transaxle should be in “Neutral position”, and apply the parking
brake securely.
1. Disconnect harness connector at oil pressure switch (1), and
remove oil pressure switch using a suitable tool.
 Oil pan (lower) (2)
⇐ Front
WBIA0776E
PBIC3310E

ENGINE OIL
LU-17
< ON-VEHICLE MAINTENANCE >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
LU
N
P O
3. Loosen oil filler cap (1) and then remove drain plug (2).
 Oil filter (3)
⇐ Engine front
4. Drain engine oil.
5. Install drain plug (2) with new washer. Refer to EM-211, "
Com-
ponent".
CAUTION:
Be sure to clean drain plug (2) and install with new washer.
6. Refill with new engine oil.
Refer to MA-19, "
Fluids and Lubricants".
CAUTION:
 The refill capacity depends on the engine oil temperature
and drain time. Use these specifications for reference
only.
 Always use oil level gauge to determine the proper
amount of engine oil in the engine.
7. Warm up engine and check area around drain plug (2) and oil fil-
ter (3) for engine oil leakage.
8. Stop engine and wait for 10 minutes.
9. Check the engine oil level. Refer to LU-15, "
Inspection".
PBIC3915E