reverse NISSAN TIIDA 2007 Service Repair Manual

TM-710
< DISASSEMBLY AND ASSEMBLY >[6MT: RS6F94R]
REVERSE IDLER SHAFT AND GEAR
5. Remove needle bearings (1) and washer from reverse idler
shaft.
AssemblyINFOID:0000000001381658
Note the following, and assemble in the reverse order of disassembly.
CAUTION:
 Never reuse snap ring.
 Make sure that snap ring is securely installed in the groove.
PCIB1761E

SERVICE DATA AND SPECIFICATIONS (SDS)
TM-715
< SERVICE DATA AND SPECIFICATIONS (SDS) [6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General SpecificationINFOID:0000000001381667
TRANSAXLE
Engine type MR18DE K9K
Transaxle modelRS6F94R
Number of speeds6
Synchromesh typeWarner
Shift pattern
Gear ratio 1st3.7273
2nd 2.1053 1.9474
3rd 1.4516 1.3226
4th 1.1714 0.975
5th 0.9714 0.7632
6th 0.8108 0.6383
Reverse 3.6865
Final gear 3.9333 3.7333
Number of teeth Input gear 1st 11
2nd 19
3rd 31
4th 35 40
5th 35 38
6th 37 47
Reverse 11
Main gear 1st 41
2nd 40 37
3rd 45 41
4th 41 39
5th 34 29
6th 30
Reverse 42
Reverse idler gear Input/Output 28/29
Final gear Final Gear/Pinion 59/15 56/15
Side Gear/Pinion
mate gear13/10
Oil capacity
(US pt, Imp pt)Approx. 2.0 (4-1/4, 3-1/2)
Remarks Reverse synchronizer Installed
Triple-cone synchronizer 1st and 2nd
PCIB1769E

CONTROLLER
VTL-7
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
ON-VEHICLE REPAIR
CONTROLLER
Removal and InstallationINFOID:0000000001696279
REMOVAL
1. Remove cluster lid C and instrument finisher D. Refer to IP-11, "Removal and Installation".
2. Remove the front air control screws and release the front air
control clips, and then remove the front air control.
INSTALLATION
Installation is in the reverse order of removal.
Disassembly and AssemblyINFOID:0000000001696280
DISASSEMBLY
SJIA0687E
1. Front air control 2. FRE button 3. MODE ring
4. TEMP ring 5. A/C finisher 6. A/C button
7. TEMP button 8. REC button 9. LCD ring
10. Rear DEF button 11. AUTO button 12. FAN button
13. MODE button
ZJIA0641J

VTL-8
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
CONTROLLER
1. Remove rear DEF button (1) using a suitable tool (A) as shown.
2. Remove A/C button (1) using a suitable tool (A) as shown.
3. Remove FRE button (1) and REC button (2) using a suitable tool
as shown.
ASSEMBLY
Assembly is in the reverse order of disassembly.
ZJIA0792J
ZJIA0793J
ZJIA0794J

IN-VEHICLE SENSOR
VTL-9
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
IN-VEHICLE SENSOR
Removal and InstallationINFOID:0000000001696282
REMOVAL
1. Remove instrument lower finisher. Refer to IP-11, "Removal and Installation".
2. Remove in-vehicle sensor screw (A), and then remove in-vehi-
cle sensor (1) from instrument lower finisher (2).
INSTALLATION
Installation is in the reverse order of removal.
SJIA0688E

VTL-10
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
SUNLOAD SENSOR
SUNLOAD SENSOR
Removal and InstallationINFOID:0000000001696283
REMOVAL
1. Remove instrument upper mask using a suitable tool as shown.
2. Disconnect sunload sensor connector, and then remove sunload
sensor (1).
INSTALLATION
Installation is in the reverse order of removal.
SJIA0689E

INTAKE SENSOR
VTL-11
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
INTAKE SENSOR
Removal and InstallationINFOID:0000000001696284
REMOVAL
1. Remove the evaporator. Refer to VTL-16, "Removal and Installation".
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2. Remove the intake sensor (1) from the evaporator (2).
CAUTION:
Mark the position of intake sensor on the evaporator for
installation.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 Install the intake sensor in the same position as the original intake sensor.
 When recharging refrigerant, check for leaks.
ZJIA0798J

A/C UNIT ASSEMBLY
VTL-13
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
7. Remove console box assembly. Refer to IP-11, "Removal and Installation"
8. Remove the instrument stay nuts (A) and harness clamps (B),
and then remove instrument stay (1).
9. Disconnect intake sensor connector (1).
10. Remove instrument panel and pad. Refer to IP-11, "
Removal and Installation".
11. Remove side ventilator ducts. Refer to VTL-23, "
Removal and Installation".
12. Remove center ventilator ducts. Refer to VTL-23, "
Removal and Installation".
13. Remove the side kicking plates. Refer to INT-20, "
Removal and Installation".
14. Disconnect the fuel filler door cable and the rear hatch door cable (if equipped).
15. Remove A/C unit assembly bolts, steering member bolts, steering column nuts and harness clips.
16. Remove steering member, and then remove A/C unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
 Fill the cooling system with coolant. Refer to CO-11, "
Changing Engine Coolant" (HR16DE), CO-35, "Chang-
ing Engine Coolant" (MR18DE), CO-58, "Refilling" (K9K).
 Recharge the refrigerant. Refer to HA-29, "
HFC-134a (R-134a) Service Procedure".
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 When recharging refrigerant, check for leaks.
SJIA0646E
SJIA0690E
A/C unit assembly bolt : 6.9 N·m (0.7 kg-m, 61 in-lb)
Steering member bolt : 12 N·m (1.25 kg-m, 9 ft-lb)
Steering column nut : -Refer to ST-9, "
Removal and Installation".

VTL-16
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
EVAPORATOR
EVAPORATOR
Removal and InstallationINFOID:0000000001696371
REMOVAL
1. Remove the A/C unit assembly. Refer to VTL-12, "Removal and Installation".
CAUTION:
Cap or wrap the joint of the pipe with suitable material such as vinyl tape to avoid the entry of air.
2. Remove the air conditioner filter.
3. Remove foot duct (right). Refer to VTL-23, "
Removal and Installation".
4. Remove screws (A), and then remove expansion valve cover
(1).
NOTE:
Manual A/C system shown, automatic A/C system similar.
5. Remove screws (A), and then remove evaporator cover (1).
NOTE:
Manual A/C system shown, automatic A/C system similar.
6. Remove the evaporator (1) with lower blower case (2) from the
A/C unit assembly.
7. Remove the intake sensor (3) from the evaporator (1).
CAUTION:
Note the position of the intake sensor on the evaporator for
installation.
8. Remove the evaporator (1) from the lower blower case (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 Replace O-rings for A/C piping with new ones, and then apply compressor oil to it when installing it.
 Install the intake sensor in the same position on the evaporator.
 When recharging refrigerant, check for leaks.
SJIA0673E
SJIA0674E
SJIA0599J

HEATER CORE
VTL-17
< ON-VEHICLE REPAIR >[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
MA
B
VTL
N
O
P
HEATER CORE
Removal and InstallationINFOID:0000000001696357
REMOVAL
1. Remove the A/C unit assembly. Refer to VTL-12, "Removal and Installation".
2. Remove foot duct (left). Refer to VTL-23, "
Removal and Installation".
3. Remove the heater pipe cover screws (A), and then remove the
heater pipe cover (1).
4. Remove the heater pipe clip screw (B), and then remove the
heater pipe clip (2).
5. Slide the heater core (3) out of the A/C unit assembly to remove.
INSTALLATION
Installation is in the reverse order of removal.
SJIA0693E