wheel OPEL COMBO 2010 Owner's Manual

85
Lighting
Picture no: 18475s.tif
Main beam, headlamp flash Push stalk forward to switch from dipped
beam to main beam.
To switch to dipped beam, push lever down
again.
To operate the headlamp flash, pull stalk
towards steering wheel. The main beam is
switched on for as long as the the stalk is
held in this position.
Picture no: 14054h.tif
Turn signal lamps If the stalk is moved past the resistance
point, the turn signal lamp remains on.
When the steering wheel moves back
toward the straight-ahead position, the
turn signal lamp is automatically
deactivated.
Touch turn signal operation: press lever
until resistance can be felt and release
again.
The turn signal lamps are switched off
manually by moving the lever back to the
middle position.
Reversing lamps The reversing lamps come on when the
ignition is on and reverse gear is engaged.
Lever upwards = Right turn signal
Lever downwards = Left turn signal

87
Lighting
Picture no: 13719s.tif
Headlamp range adjustment
? 3

Rotate the adjuster wheel to the required
position to adjust the dipped beam range
to vehicle loading and prevent dazzling. Combo
Combo van
Picture no: 13722s.tif
Instrument illumination
k
Illumination comes on with the exterior
lights. Brightness can be adjusted using the
adjuster wheel.
Information display illumination
3
Information display illumination comes on
when the ignition or infotainment system is
switched on. Brightness can be adjusted
using the adjuster wheel.
0 = Front seats occupied
1 = All seats occupied
2 = All seats occupied and luggage
compartment load
3 = Driver’s seat occupied and
luggage compartment load
0 = Seats occupied
1 = Seats occupied and half load in
load compartment
2 = Seats occupied and full load in
load compartment
3 = Driver’s seat occupied and full
load in load compartment

90 Infotainment systemInfotainment system
Radio reception
3
Radio reception may be disrupted by
static, noise, distortion or loss of reception
due to
zChanges in distance from the
transmitter,
zmulti-path reception due to reflection
and
zshadowing. Infotainment system
3
The infotainment system is operated as
described in the operating instructions.
Picture no: 14034s.tif
Steering wheel remote control
3
The functions of the infotainment system3
and the information display can be
operated on the steering wheel.
Further information 378 and the
infotainment system instructions. Radio reception 3................................ 90
Infotainment system 3........................ 90
Steering wheel remote control 3........ 90
AUX input 3......................................... 91
Mobile telephones and radio
equipment (CB) 3............................. 91

100 Driving and operationDriving and operation
Manual transmission
automated
3
The Easytronic transmission permits
manual (manual mode) or automatic gear
shifting (automatic mode), both with
automatic clutch control.
Picture no: 12478s.tif
Transmission display
Shows the mode and current gear.
If the Winter programme is activated, T is
illuminated. Manual transmission automated3... 100
Manual transmission ........................... 105
Driving hints ......................................... 106
Saving Fuel, Protecting the
Environment ...................................... 108
Fuels, refuelling .................................... 110
Catalytic converter, engine exhaust .. 114
Hydraulic brake system ...................... 118
Anti-lock Braking System (ABSu)3 119
Hand brake .......................................... 120
Brake assist .......................................... 120
Wheels, tyres ........................................ 121
Roof racks 3......................................... 125
Towing equipment 3........................... 126
Caravan/trailer towing ........................ 126

119
Driving and operation
Picture no: 12482s.tif
Brake system control indicator R
The control indicator illuminates when the
ignition is switched on if the hand brake is
applied or if the brake or clutch fluid level is
too low. Brake fluid 3179. For vehicles with manual transmission
automated 3, the control indicator flashes
for a few seconds when the ignition is
turned off if the hand brake is not applied.
Anti-lock Braking System
(ABS
u)3
ABS prevents the wheels from locking.
ABS starts to regulate brake pressure as
soon as a wheel shows a tendency to lock.
The vehicle remains steerable, even during
hard braking.
ABS control is made apparent though a
pulse in the brake pedal and the noise of
the regulation process.
For optimum braking, keep the brake
pedal fully depressed throughout the
braking process, despite the fact that the
pedal is pulsating. Do not reduce the
pressure on the pedal.
Picture no: 12147s.tif
Control indicator u for ABS
It illuminates for a few seconds when
ignition is switched on. Once the control
indicator goes out, the system is ready for
operation.
If the control indicator does not go out
after a few seconds, or if it illuminates while
driving, there is a fault in the ABS. The
brake system remains operational without
ABS regulation.
9 Warning
If the control indicator illuminates when
the handbrake is released, stop driving
immediately. Contact a workshop for
assistance.

120 Driving and operationSelf testing
When the engine is started and the vehicle
starts off, the system performs a self-check,
which may be audible.
Fault
Have cause of fault remedied by a
workshop. The system’s integrated self
diagnostics allow faults to be quickly
remedied.
Picture no: 12481s.tif
Hand brake Always apply handbrake firmly without
operating the release button, and apply as
firmly as possible on a downhill or uphill
slope.
To release the hand brake pull the lever up
slightly, press the ratchet knob, and fully
lower the lever.
In order to reduce the hand brake
operational forces, depress the foot brake
at the same time.
Brake assist When the brake pedal is rapidly and
forcefully depressed, the vehicle is
automatically braked with maximum brake
force amplification in order to obtain the
shortest possible braking distance during
full-on braking (brake assist).
Maintain steady pressure on the brake
pedal for as long as full-on braking is to
continue. When the brake pedal is
released, the maximum brake force
amplification is taken away.
9 Warning
If there is a fault in the ABS, the wheels
may be liable to lock due to braking that
is heavier than normal. The advantages
of ABS are no longer available. During
hard braking, the vehicle can no longer
be steered and may swerve.

121
Driving and operation
Wheels, tyres Suitable tyres or limitations 3191.
Tyres fitted in the factory are adapted to
the chassis and provide optimum driving
comfort and safety.
Changing tyre/wheel type
If tyres of a different size than those fitted
at the factory are used, it may be
necessary to reprogram the electronic
speedometer and make other vehicle
modifications.
After converting to a different tyre size,
have the adhesive label with tyre pressures
replaced. Fitting new tyres
Fit tyres in pairs or in sets, which is even
better. Ensure that tyres on one axle are
zthe same size,
zthe same design,
zthe same make,
zand have the same tread pattern.
Fit directional tyres such that they roll in the
direction of travel. The rolling direction is
indicated by a symbol (e.g. an arrow) on
the sidewall.
Tyres fitted opposing the rolling direction
(such as when changing a tyre) should be
refitted as soon as possible. This is the only
way to benefit fully from the design
properties of the tyre.
Pay attention to legal requirements when
disposing of tyres.
Picture no: 12117s.tif
Tyre pressure
Check tyre pressure at least every 14 days
and prior to any long journey; the tyres
should be checked when cold. Don’t forget
to check the spare 3.
Remove the valve cap key from the tank
flap and use it to unscrew the valve cap.
Tyre pressure 3191, 3192 and on the
adhesive label on the inside of the tank
flap.
The tyre pressure data is for cold tyres. It
applies to both summer and winter tyres.
9 Warning
Use of unsuitable tyres or wheels may
lead to accidents and render the vehicle
unroadworthy.

122 Driving and operationAlways inflate the spare wheel 3 to the
pressure specified for full load.
Do not reduce tyre pressure when the tyres
are warm. Otherwise the pressure may
drop below the permissible minimum when
the tyres cool down.
After having checked the tyre pressure,
tighten the valve caps using the valve cap
key.
Incorrect inflation pressures will impair
safety, vehicle handling, comfort and fuel
economy and will increase tyre wear.
Picture no: 9358t.tif Picture no: 15941s.tif
Tyre condition, wheel condition
Drive over edges slowly and at right angles
if possible. Driving over sharp edges can
cause tyre and wheel damage. Do not trap
tyres on the kerb when parking.
Regularly check the wheels for damage.
Seek the assistance of a workshop in the
event of damage or unusual wear.
9 Warning
If the pressure is too low, this can result
in considerable tyre warm-up and
internal damage, leading to tread
separation and even to tyre blow-out at
high speeds.

123
Driving and operation
Picture no: 6457u.tif
Tread depth
Check tread depth regularly.
For reasons of safety, tyres should be
replaced when their tread depth has worn
down to 2 to 3 mm (winter tyres: 4 mm).
The legally permissible minimum tread
depth (1.6 mm) has been reached when
the tread has worn down as far as one of
the wear indicators (TWI
1)). A number of
wear indicators are spaced at equal
intervals around the tyre within the tread.
Their position is indicated by markings on
the tyre sidewall.
Picture no: 6456u.tif
If wear in the front is greater than that in
the rear, switch the front wheels with the
rear ones.
Correct tyre pressure. General information
zThe danger of aquaplaning is greater if
the tyres are worn.
zTyres age, even if they are little used or
not used at all. We recommend tyre
replacement no later than every 6 years.
zNever fit used tyres the previous history
and use of which you do not know.
1)TWI
= Tread
Wear
Indicator.

124 Driving and operationTyre designations
Meanings:
e.g. 175/70 R 14 79 T
Speed code letters: Winter tyres 3
Instructions on fitting new tyres 3121.
Limitations 3191.
Winter tyres improve driving safety at
temperatures below 7 C.
The design of summer tyres means they
have limited qualities for winter driving.
In accordance with country-specific
regulations, affix the speed sticker 3 in the
driver’s field of view.
Use of a spare wheel fitted with a summer
tyre may affect the vehicle’s driveability,
especially on slippery road surfaces.
Obtain a replacement for the faulty tyre as
soon as possible, and have the wheel
balanced and fitted to the vehicle.
Wheel trims 3
The use of wheel trims and tyres that Opel
has approved for the vehicle and therefore
fulfill all requirements for the relevant
combination of wheels and tyres.
If the wheel trims and tyres used are not
Opel-approved, the tyres must not have a
beaded edge. Wheel trims must not impair brake cooling.
Remove the wheel trims if fitting tyre
chains3.
175= Tyre width in mm
70= Cross-section ratio (tyre height to
tyre width in %)
R= Belt type Radial
14= Rim diameter in inches
79= Load index e. g.: 79 corresponds
to 437 kg
T= Speed code letter
Q= up to 160 km/h
S= up to 180 km/h
T= up to 190 km/h
H= up to 210 km/h
V= up to 240 km/h
W= up to 270 km/h
9 Warning
Use of unsuitable tyres or wheel trims
could lead to sudden loss of air and
thereby accidents.