Back OPEL FRONTERA 1998 Workshop Manual

WIRING SYSTEM 8D–401
STEP OPERATION ITEM TO BE CHECKEDITEM OF
REMARKS
MALFUNCTION
Be sure to lock door
with locking knob.
Activate alarm
device.
All doors are
unlocked.
With key set at unlock
position, check to see
if alarm stops.
All doors are
locked.
Activate alarm
device.
Activate alarm
device.
Only left rear door
is unlocked. Check to see if engine hood,
tailgate and doors are closed and
locked.
Check to see if indicator light
remains lit off.
Check to see if indicator light
flashes.
Check to see if dome light and
courtesy light illuminate.
Check to see if indicator light
changes from flashing to steadily
on.
Check to see if indicator light
turns off in about 10 seconds.
Check to see if alarm operates
(with headlight flashing, and horn
blaring intermittently.)
Check to see if alarm stops.
Check to see if indicator light
turns on.
Check to see if indicator light
goes off after about 10 seconds.
Check to see if alarm does not
operate.
Check to see if indicator light
turns on.
Check to see if indicator light
goes off after about 10 seconds.
Check to see if alarm starts. Turn starter key to “ON” position.
Open windows fully.
Pull out starter key after turning it
back to “OFF” position.
Unlock left front door with locking
knob.
Open left front door. (And get out
of the vehicle.)
Close left front door.
Lock left front door.
Wait about 10 seconds
Unlock left front door with locking
knob.
Insert key into key cylinder of left
front door and turn it in unlock
direction.
Lock left front door.
Wait for about 10 seconds.
Unlock left front door with key.
Lock left front door with key.
Wait for about 10 seconds.
Unlock left rear door with locking
knob.K
A
B
C
D
E
B
C
F
B
C
D 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

8D–408 WIRING SYSTEM
Step Action Yes No
The control unit makes lock/unlock response once with interval of
one second.
Is the response complete?
The control unit makes lock/unlock response three times with
interval of one second.
Is the response complete? 12
13Finished
Finished—
—
Step Action Yes No
1. Open the driver’s side door.
2. Turn the starter switch off.
Is the action complete?
Turn the starter switch to ACC position and then off three times
within five seconds after step 1.
Is the action complete within five seconds?
Close the door and then open it two times within ten seconds after
step 2.
Is the action complete within ten seconds?
1. Turn the starter switch to ACC position and then off.
2. Close the door and then open it.
NOTE: This step must be performed within ten seconds after step
3.
Is the action complete?
The control unit makes lock/unlock response twice as many the
number of registered ID code with interval of two seconds. (In case
of no registered code, the response is made ten times.)
Is the response complete? 1
2
3
4
5Go to Step 2
Go to Step 3
Go to Step 4
Go to Step 5
Finished—
Finished
Finished
Finished
—
This procedure checks how many kinds of ID code are
registered.
Step Action Yes No
Open the driver’s side door.
Is the action complete?
Lock the door and then unlock it three times within ten seconds
after step 1.
Is the action complete within five seconds?
Close the door and then open it two times within ten seconds after
step 2.
Is the action complete within ten seconds? 1
2
3Go to Step 2
Go to Step 3
Go to Step 4—
Finished
Finished Anti–theft horn, as an answer back function for the
transmitter operation, changes from available into
unavailing or from unavailing into available by this
procedure.

WIRING SYSTEM 8D–409
Step Action Yes No
1. Lock the door and unlock it three times.
2. Close the door and then open it.
NOTE: This step must be performed within ten seconds after step
3.
Is the action complete?
Answer back mode changes.
Is this step complete?
The control unit makes lock/unlock response once with interval of
one second.
Is the response complete?
The control unit makes lock/unlock response three times with
interval of one second.
Is the response complete? 4
5
6
7Go to Step 5
Go to Step 6
Finished
FinishedFinished
Go to Step 7
—
—
1. Remove and install the control unit.
Refer to Anti–theft & Keyless Entry Control Unit
Removal and Installation in this section.
2. Register ID code.
Refer to ID Code Registration in this section.
3. Check that the keyless entry system works normally.
1. Prepare a new transmitter.
2. Register ID code.
Refer to ID Code Registration in this section.
3. Check that the keyless entry system works normally.
1. Remove a screw to remove the cover.
2. Remove the batteries.
3. Set the new batteries into the transmitter.
4. Install the cover to the transmitter.
5. Check that the keyless entry system works normally.

D08RW639
3.0
B/Y
0.85
R/B
0.85
G/R 0.85
R/BC-3 10A
TURN,BACKSTARTER SW
(IG1)
STARTER SW
(ST)
12
C-93
13
C-931
C-93
H-717
H-41 TAIL RELAY
(4)
PCM
(E12)PCM
(E7)PCM
(F2)PCM
(F3)BACK UP
LIGHTSTARTER
RELAY
(5) 1
H-531 0.5
R/B
0.75
R/B
0.5
L/W0.5
L/Y0.5
L/B
0.5
L/W0.5
L/Y0.5
L/B 0.5
L/W0.5
L/Y0.5
L/B0.5
Y/G0.75
R/L1.25
W/L 1.25
W/R
MODE
SW
M-25
5 6
8H-11M-25
A/T SHIFT INDICATOR CONTROL UNIT
2
C-93H-532M-25
6
3
C-93H-533M-25
7
H-534M-25
2
H-117M-25
3
H-1015M-254M-25
1H-1016

D08RW949
3.0
B/Y
0.85
R/B
0.85
G/R 0.85
R/BC-3 10A
TURN,BACKSTARTER SW
(IG1)
STARTER SW
(ST)
12
C-93
13
C-9313H-42
1
C-93
H-84
TAIL RELAY
(4)
PCM
(E12)PCM
(E7)PCM
(F2)PCM
(F3)BACK UP
LIGHTSTARTER
RELAY
(6)
H-531 0.85
R/B
0.75
R/B
0.5
L/W0.5
L/Y0.5
L/B
0.5
L/W0.5
L/Y0.5
L/B 0.5
L/W0.5
L/Y0.5
L/B0.5
Y/G0.75
R/L1.25
W/R 1.25
W/L
MODE
SW
M-25
5 6
8H-11M-25
A/T SHIFT INDICATOR CONTROL UNIT
2
C-93H-532M-25
6
3
C-93H-533M-25
7
H-534M-25
2
H-117M-25
3
H-1016M-251M-25
4H-1015

D08RW648
H HH
K K
B-29 STARTER SW
(IG2)
1.25
G/R
0.85
GR/L
0.85
W0.85
Y/V
0.85
W/R0.85
B
2.0
B0.85
G/R 3.0
B/R
C-2 15A
SEAT HEATERSEAT HEATER SW-RH2
3
B-29
4B-29
1B-29
5
H-57 2H-57
H HH
K K
B-31
0.85
L/G
0.85
W0.85
Y/G
0.85
W/R0.85
B0.85
B/W
0.85
BSEAT HEATER SW-LHSEAT
HEATER-RH2
3
B-31
SEAT CUSHION SEAT
BACK
4B-31
1B-31
5
H-58 2H-58
B-26
BODY-CTR 2.0
BB-2
BODY-LH 2.0
BB-18
BODY-RH
T-8
4
H-5733
T- 8 1T- 8 0.85
W0.85
W/R
0.85
B/W
0.85
B
SEAT
HEATER-LH
SEAT CUSHION SEAT
BACK
T-1 0
4
H-5833
T-1 0 1T-1 0 0.85
W0.85
W/R

D08RW948
H HH
K K
B-29 STARTER SW
(IG2)
1.25
GR
0.85
GR/L
0.85
W0.85
Y/V
0.85
W/R0.85
B
2.0
B0.85
GR 3.0
B/R
C-2 15A
SEAT HEATERSEAT HEATER SW-LH2
3
B-29
4B-29
1B-29
5
H-57 2H-57
BA
H HH
K K
B-31
0.85
L/G
0.85
W0.85
Y/G
0.85
W/R0.85
B0.85
B/W
0.85
BSEAT HEATER SW-RHSEAT
HEATER-LH2
3
B-31
SEAT CUSHION SEAT
BACK
4B-31
1B-31
5
H-58 2H-58
DC
B-2
BODY-RH
2.0
B
B-26
BODY-CTR
2.0
B
B-18
BODY-LH
T-8
4
H-5733
T- 8 1T-8 0.85
W0.85
W/R
AB
0.85
B/W
0.85
B
SEAT
HEATER-RH
SEAT CUSHION SEAT
BACK
T-1 0
4
H-5833
T- 1 0 1T- 1 0 0.85
W0.85
W/R
CD

8F–6BODY STRUCTURE
General Description
This section describes how to remove and install front
and rear bumpers. Each bumper is installed with two
fixing bolts used on either side to fasten the backbar to theframe, a slider is used to fasten the bumper fascia to the
fender panel. The bumpers can be removed by taking
them out forward or backward after removing the two
fixing bolts on either side.
Front Bumper
Parts Location
601RW015
Legend
(1) Front Bumper Retainer Bolt
(2) Front Bumper Assembly
(3) Support Fixing Clip
(4) Bumper Spacer Support
(5) Back Bar Fixing Bolt
(6) Front Fog Light Connector
(7) Front Bumper Slider Fixing Clip(8) Front Bumper Slider
(9) Front Bumper Slider Fixing Nut
(10) Bumper Fascia Lower Bolt
(11) Front Fog Light Assembly
(12) Reinforce Assembly
(13) Reinforce Lower Bolt
(14) Front Bumper Fixing Bolt

8F–7 BODY STRUCTURE
Removal
1. Disconnect battery ground cable.
2. Remove front fog light connector.
3. Remove front bumper assembly fixing bolt.
Remove the two bolts from both sides of the front
bumper.
601RW010
4. Remove front bumper assembly.
5. Remove bumper fascia lower bolts.
6. Remove front bumper retainer.
7. Remove reinforce lower bolts.
Loosen the five bolts and release claws.
8. Remove reinforce assembly.9. Remove backbar fixing bolts.
Remove the four bolts at each backbar.
10. Remove front fog light assembly.
11. Remove the front bumper slider(1).
Remove the two clips(4) and the two nuts(3), and
release the claw from the washer(2).
601RW009
Installation
To install, follow the removal steps in reverse order noting
the following points:
1. Tighten the front bumper assembly fixing bolts to the
specified torque.
To r q u e : 1 3 2 N
m (13.5kgꞏm/98 lb ft)
Front Bumper Slider Bracket
Removal
1. Disconnect battery ground cable.
2. Remove the Front bumper.
Refer to Front Bumper in this section.
3. Remove the three nuts(1) and draw out the slider
bracket(2).
601RW003
Installation
To install, follow the removal steps in reverse order.

8F–8BODY STRUCTURE
Rear Bumper
Parts Location
690RW001
Legend
(1) Back Bars
(2) Reinforce Assembly
(3) Rear Bumper Slider Brackets
(4) Rear Step Clips
(5) Reinforce Lower Screws
(6) Reinforce Upper Bolts
(7) Rear Bumper Fascia Brackets(8) Rear Bumper Fascia Bracket Screws
(9) Rear Bumper Assembly
(10) Rear Bumper Side Covers
(11) Mud Flaps
(12) Rear Bumper Assembly Fixing Bolts
(13) Rear Bumper Retainers
(14) Clips
Removal
1. Remove rear bumper side covers.2. Remove mud flaps.Remove three screws.
3. Remove bumper fascia bracket screws.