light OPEL MERIVA 2009 Owner's Manual

52 Seats, InteriorTo achieve a flat loading surface in the
extended luggage compartment, the
outboard seats can be lowered slightly. We
recommend however only using the seats
as seats in the raised position. Extending
the luggage compartment 353.
Flexible Seat System (FlexSpace)The rear seat row on the Meriva can be
fitted with three seats in Variant 1, or two
seats with maximum seating space in
Variant 2. In Variant 2, the centre seat is
lowered.
The luggage compartment can only be
extended in Variant 1 353.
To extend the luggage compartment, the
outboard seats can be lowered slightly
3 54.
Picture no: 14730s.tif
Variant 1: Three rear seats
Set seat backrest to centre position using
the handle on the outside of the seat 351.
Pull the handle beneath the seat. Slide the
seat all the way forward, then outward
toward the door and then further forward
to the desired position.
Release handle and allow seat to engage
in position.
Raise centre seat 354.
9 Warning
To prevent injuries, always hold back
seat backrest firmly and guide
downward when folding.

61
Seats, Interior
Picture no: 17885s.tif
Control indicator v for belt tensioners
The function of the belt tensioners and
airbag systems is monitored electronically
and indicated via control indicator v.
When the ignition is turned on, the control
indicator comes on for about 4 seconds.
If it does not light, does not go out after
4 seconds or comes on during driving,
there is a fault in the belt tensioner or
airbag systems 372.The systems may fail
to deploy in the event of an accident.
Deployment of the belt tensioners is
indicated by continuous illumination of v . The system’s integrated self-diagnostics
allows faults to be quickly remedied.
Important
z
Do not affix or place accessories or other
objects within the deployment zone of
the belt tensioners. Do not make any
modifications to belt tensioner
components as this will invalidate the
vehicle type approval. z
The belt tensioner and airbag system
control electronics can be found in the
centre console area. In order to avoid
malfunctions, do not store magnetic
objects in this area.
z When the rear seats are being used it
must be ensured that the components of
the front seat belts are not damaged by
shoes or other objects. Do not allow dirt
to penetrate the seat belt inertia reels.
z We recommend that you have the seats
removed by a workshop.
z The belt tensioners only deploy once,
which can be detected by illumination of
the control indicator v . Have deployed
belt tensioners replaced by a workshop.
z The applicable safety regulations must
be adhered to when the vehicle is
disposed of. The vehicle should therefore
be disposed of by a recycling company.
9 Warning
Have the cause of the fault remedied
immediately by a workshop.
9 Warning
Incorrect handling (e.g. removal or
fitting of seat belts or belt buckles) can
cause the belt tensioners to deploy, with
risk of injury.

72 Seats, InteriorThe curtain airbags will not be triggered in
the event of
zthe ignition is switched off,
z frontal collisions,
z accidents in which the vehicle overturns,
z collisions involving a rear impact,
z collisions involving a side impact outside
the passenger cell.
Picture no: 17885s.tif
Control indicator v for airbag systems
The function of the airbag systems and
seat occupancy recognition 3 is monitored
electronically and indicated via control
indicator v. When the ignition is turned on,
the control indicator comes on for
about 4 seconds. If it does not light, does
not go out after 4 seconds or comes on
during driving, there is a fault in the airbag
systems, the seat occupancy recognition
system 3 or the belt tensioners 361. The
systems may fail to deploy in the event of
an accident.
Deployed airbags are indicated by
continuous illumination of v. The system’s integrated self-diagnostics
allows faults to be quickly remedied.
Seat occupancy recognition
3
The seat occupancy recognition system
deactivates the front and side front
passenger airbags if the front passenger
seat is unoccupied or an Opel child
restraint system with transponders 3 has
been fitted to the front passenger seat. The
curtain airbag system 3 remains activated.
The control indicator for seat occupancy
recognition
y is located in the courtesy
lamp. If this control indicator
y illuminates
for approx. 4 seconds after the ignition is
switched on, the vehicle is equipped with
seat occupancy recognition 373,
Fig. 12097 S.
If an Opel child restraint system with
transponders 3 is fitted, this control
indicator
y lights permanently after the
ignition is switched on as soon as the
system has detected the child restraint
system. Only then may the child restraint
system with transponders 3 be used on the
passenger seat.
9 Warning
Keep the area in which the airbag
inflates clear of obstructions.
9 Warning
Have the cause of the fault remedied
immediately by a workshop.

74 Seats, InteriorIf the control indicator flashes when the
child restraint system with transponders 3
is correctly fitted, there is a fault with risk of
injury to the child. Fit child restraint systems
on the rear seat. Have the cause of the
fault eliminated by a workshop.
If no Opel child restraint system with
transponders 3 is fitted, the control
indicator must not light or flash as the
passenger airbag systems would not
deploy. Have the cause of the fault
eliminated by a workshop. Important
z
Placing accessories and objects in the
expansion region of the airbag systems
is not permitted due to the risk of injury if
the airbag is triggered.
z Do not place any objects between the
airbag systems and the vehicle
occupants; danger of injury.
z Use the hooks in the roof frame only to
hang up light articles of clothing or coat
hangers. Do not place any objects in the
pockets of the hanging items – risk of
injury.
z The airbag systems and belt tensioner
control electronics can be found in the
centre console area. In order to avoid
malfunctions, do not store magnetic
objects in this area. z
Do not stick anything on the steering
wheel, instrument panel, front seat
backrests or roof frame in the vicinity of
the airbags, or on the front passenger’s
seat cushion, or cover any of those areas
with other materials.
z Use only a dry cloth or interior cleaner to
clean the steering wheel, instrument
panel, front seat backrests, roof frame
and seat cushion of the front passenger
seat. Do not use any aggressive cleaning
agents.
z Only protective covers which are
approved for your vehicle with side
airbag may be fitted on the front seats.
When fitting the protective covers, make
sure that the airbag units on the
outboard sides of the front seat
backrests are not covered.
z The airbag systems are triggered
independently of each other depending
on the severity of the accident and the
type of impact. The side airbag system 3
and the curtain airbag system 3 are
triggered together.
z Each airbag deploys once only. Have a
workshop replace deployed airbags
immediately.
9 Warning
If the Opel child restraint system with
transponders 3 has been fitted
according to the inst ructions, the control
indicator for Opel restraint systems with
transponders must illuminate in the
courtesy lamp when the ignition is
switched on.
If the control indicator does not come on
while driving, the passenger airbag
systems are not de-activated and there
is a risk of injury or death. In this case fit
child restraint system s on the rear seat.
Have the cause of th e fault eliminated
by a workshop.
9 Warning
As with any other ob ject, child restraint
systems must not be carried on a
passenger’s lap. Danger to life.

78 Seats, Interior
Picture no: 14111s.tif
Cigarette lighter
3
The cigarette lighter is behind the ashtray
cover in the centre console.
The ashtray cover opens when pressed at
the point indicated.
Press cigarette lighter with ignition
switched on. Switches off automatically
when element is hot. Withdraw cigarette
lighter.
Picture no: 16111s.tif
Accessory sockets
3
The accessory socket is behind the cover in
the centre console. Further accessory
sockets3 are located in the centre console
in front of the rear seats and in the luggage
compartment.
Accessory sockets are operable when the
ignition is switched on. Use of the sockets
while the engine is no t running will drain
the battery. Do not exceed the maximum power
consumption of 120 watts.
Electrical accessories connected to the
socket must comply with the
electromagnetic compatibility
requirements laid down in DIN VDE 40 839,
otherwise vehicle malfunctions may occur.
Do not connect any current-delivering
accessories, e.g. el
ectrical charging
devices or batteries.
If the tyre repair set is 3 is in operation, no
consumers may be connected to the
auxiliary socket.
Caution
Do not damage the socket by using
unsuitable plugs.

82 Instruments, ControlsInstruments, ControlsControl indicators ................................ 82
Instrument display ............................... 87
Information display ............................. 90
Warning buzzers.................................. 100
Windscreen wipers ............................... 100
Picture no: 17876s.tif
Control indicators The control indicators described here are
not present in all vehicles. The description
applies to all instrument versions.
The colours of the control indicators mean:
Picture no:
X
Seat belt 3
Control indicator lights up red.
This comes on after turning on the ignition
(with warning tone) until the seat belt is
done up.
Fasten seat belt 362. B
Adaptive headlamp 3 (AFL)
Control indicator lights up and/or flashes
yellow.
Lamps

Fault in system. Contact a workshop for
assistance.
z
Red
Danger, important reminder.
z Yellow
Warning, information, fault.
z Green
Switch-on confirmation.
z Blue
Switch-on confirmation.

83
Instruments, Controls
Picture no: 18385s.tif
Flashes

System converted to symmetrical dipped
beam.
Control indicator
B
flashes for
approximately 4 seconds after the ignition
is switched on as a reminder that the
system has been converted 3110.
AFL 3106.
>

Fog lamps 3
Control indicator lights up green.
This comes on when the front fog lamps
are switched on 3103.
Picture no:
A

Engine electronics, transmission
electronics, immo biliser, diesel fuel filter 3
Control indicator lights up and/or flashes
yellow.
It illuminates for a few seconds when the
ignition is switched on.
Illuminates when the engine is running
Fault in engine electronics or transmission
electronics. Electr onics switches to
emergency running program, fuel
consumption may increase and driveability
of vehicle may be affected 3143. If the
fault is still there when the engine is started
again, contact a workshop for assistance.
For vehicles with diesel engine, the diesel
fuel filter may need to be drained of water
3 212.
Flashes when the ignition is onFault in the electronic immobiliser system;
the engine cannot be started 327. Z

Exhaust emission
Control indicator lights up and/or flashes
yellow.
It illuminates when the ignition is switched
on and goes out shortly after the engine
starts.
Illuminates when the engine is running
Fault in emission control system. The
permissible emission limits may be
exceeded. Contact a workshop for
assistance immediately.
If it flashes when the engine is runningFault that could lead to catalytic converter
damage. Ease up on the throttle until the
flashing stops 3143. Seek the immediate
assistance of a workshop. v
Airbag systems 3, Belt tensioners
Control indicator lights up red.
Illuminates when the engine is runningFault in zone of airbag system or belt
tensioners 361, 372.

84 Instruments, Controls
Picture no: 17876s.tif
I

Engine oil pressure
Control indicator lights up red
It illuminates when the ignition is switched
on and goes out shortly after the engine
starts.
Illuminates when the engine is running
1. Depress clutch.
2. Move gearshift lever to neutral, or with
manual transmissi on automated 3 place
selector lever in N.
Picture no:
3. Move out of the flow of traffic as quickly
as possible without impeding other
vehicles.
4. Switch off ignition.
Contact a workshop for assistance.
Caution
Engine lubrication may be interrupted.
This may result in damage to the engine
and/or locking of the drive wheels.
9 Warning
When the engine is off, considerably
more force is needed to brake and steer.
Do not remove key until vehicle has
come to a standstill, otherwise the
steering column lock could engage
unexpectedly.
O

Turn signal lamps
Control indicator flashes green.
The control indicator flashes if a turn signal
or the hazard warning flashers are
activated.
Rapid flashing: failure of a direction
indicator lamp or associated fuse.
Change bulbs 3 185. Fuses 3182.
C

Main beam
Control indicator lights up blue.
It is illuminated when main beam is on and
during headlamp flash 311, 3102.
j

Automatic transmission 3, start engine.
Control indicator lights up yellow.
The engine can only be started if the foot
brake is depressed. If the foot brake is not
depressed, the control indicator illuminates
3 130.

85
Instruments, Controls
Picture no: 18385s.tif
T
Winter mode for manual transmission
automated 3
Control indicator lights up yellow.
Control indicator lights up when winter
program is enabled 3132. m

Cruise control 3
Control indicator lights up green
This comes on when the system is switched
on 3148.
r
Fog tail lamp
Control indicator lights up yellow.
This comes on when the fog tail lamp is
switched on 3104.
Picture no:
p

Alternator
Control indicator lights up red.
It illuminates when the ignition is switched
on and goes out shortly after the engine
starts.
Illuminates when the engine is running
Stop, switch off engine. Battery is not
charging. Contact a workshop
immediately. R

Brake system, clutch system
Control indicator lights up or flashes red.
Illuminated
Illuminates when the ignition is switched on
if the hand brake is applied 3151.
Lights up when the hand brake is released
when the fluid level for the brake or clutch
systems is low 3214.
FlashesOn vehicles with manual transmission
automated 3, control indicator R flashes
for a few seconds after the ignition is
switched off when the hand brake has not
been applied. u

Anti-lock brake system
Control indicator lights up red.
Illuminates while driving
Fault in anti-lock braking system 3152. S

Engine oil level 3
Control indicator lights up yellow.
The engine oil level is checked
automatically 3.
Illuminates when the engine is running

Engine oil level too lo w. Check engine oil
level and top up engine oil if necessary
3 210.
9 Warning
Stop. Do not continue your journey.
Consult a workshop.

86 Instruments, Controls
Picture no: 17876s.tif
EPS
1)
Electric power steering
Control indicator lights up yellow.
Fault in electr ical power steering. Vehicle
can still be driven, but greater force is
required for steering. Contact a workshop
immediately.
v
Electronic Stability Program (ESP ®
Plus
)3
Control indicator flashes or lights up
yellow.
Flashing during driving
System engages 3146.
Illuminates while drivingFault in system 3146.
Picture no:
Y
Fuel level
Control indicator lights up and/or flashes
yellow.
Lamps

Level in fuel tank too low.
Flashes
Fuel level is used up, fuel immediately.
Never let the tank run dry!
Erratic fuel supply can cause catalytic
converter to overheat 3142.
Diesel engines: Bleed the fuel system after
running empty 3165.
1)EPS
= Electric
Power
Steering.
!

Preheating system 3, Diesel particle
filter 3
Control indicator lights up and/or flashes
yellow.
Illuminated
Preheating activated. Only activates when
outside temperatures are low.
Flashes(in vehicles with dies el particle filter)
Control indicator ! flashes if the filter
requires cleaning and previous driving
conditions did not permit automatic
cleaning. Continue driving and if possible
do not allow engine speed to drop
below 2000 rpm.
The control indicator ! goes off as soon
as the self-cleaning op eration is complete.
Diesel particle filter 3 144.