engine PEUGEOT 108 2015 User Guide

18
Stop & Star t
(VTi 68 S&S
engine)flashing.th
e Stop & Start system has a fault. Have the system checked by a Pe ugeOt dealer or a
qualified workshop.
Speed limiter fixed.
th

e speed limiter has a fault.Have it checked by a P
e

uge
Ot
dealer or a qualified
workshop.
Door(s) open /
Boot open fixed, accompanied by
an audible signal. A door or the boot is still open. Close the door or boot.
Warning / indicator lamp
StateCause Action / Observations
Under-inflation fixed.
th
e pressure in one or more wheels
is too low. Check the pressure of the tyres as soon as possible.
th
is check should preferably be carried out when the
tyres are cold.
You must reinitialise the system after the adjustment
of one or more tyre pressures and after changing one
or more wheels.
For more information, refer to the "
un
der-inflation
detection" section.
Monitoring

21
108_en_Chap01_controle-de-marche_ed01-2015
Parking brakefixed, accompanied by
an audible signal.th e parking brake is applied or not
properly released. Release the parking brake to switch off the warning
lamp, keeping your foot on the brake pedal.
Observe the safety recommendations.
For more information on the parking brake, refer to the
corresponding section.
Warning / indicator lamp
StateCause Action / Observations
Passenger's
front airbag fixed in the seat belt
and passenger's front
airbag warning lamps
display.
th

e control switch, located in the
glove box, has been placed in the
"ON" position.
the

passenger's front airbag is activated.
In this case, do not install a rear ward facing child seat.
Stop & Star t
(VTi 68 S&S
engine) fixed.
When the vehicle stops (red lights,
traffic jams...) the Stop & Start system
has put the engine into S
tO

P mode.
th
e indicator lamp goes off and the engine restarts
automatically in S
tA

R
t
mode, as soon as you want to
move off.
Keyless Entr y
and Starting
system fixed.
th

e conditions for starting are met. For more information, refer to the "Starting - switching off the engine with the Keyless
e
n
try and Starting
system" section.
flashing slowly.
th

e vehicle is in "ACC" mode.
th

e accessories (audio system,
12V socket...) can be used.
1
Monitoring

22
Warning / indicator lampStateCause Action / Observations
Gear shift
indicator fixed.
You can change up. For more information, refer to the corresponding
section.
You can change down (only for the
V
ti 6

8 engine).
Speed limiter
(VTi 68 engine) fixed.
th

e speed limiter is active.
Lane depar ture
warning system fixed.
th

e button has been pressed.
th
e lane departure warning system has been
activated.
For more information, refer to the corresponding
section.
fixed.
th

e system is operational: it has detected road
markings to the left and /or right.
For more information, refer to the corresponding
section.
Active City
Brake fixed.
th

e button has been pressed.
th
e Active City Brake system has been activated.
For more information, refer to the corresponding
section.
Monitoring

24
Warning / indicator lampStateCause Action / Observations
Stop & Star t
( VTi 68 S&S
engine) fixed.
th

e Stop & Start system has been
deactivated. Reactivate the system by pressing the button again.
For more information, refer to the corresponding
section.
Active City
Brake fixed.
th

e Active City Brake system has
been deactivated. Reactivate the system by pressing the button again.
For more information, refer to the corresponding
section.
Monitoring

25
108_en_Chap01_controle-de-marche_ed01-2015
Indicators
Total/trip distance recorder
Press one of the buttons 1 to alternate the
distance display:
-
t
otal with "ODO" (odometer) displayed,
-

t
rip with "TRIP" displayed.
to r

eset the trip recorder to zero, when
it is displayed, press and hold one of the
two
buttons 1 .
When the ignition is switched on, the distance
recorder selected when the engine was
switched off is displayed.th
is indicates the quantity of fuel available:
- 1/ 1 and six bars, the fuel tank is full.
-

R
and one bar flashing, the fuel tank is on
the reserve.
Low fuel level
When the low level in the fuel tank is reached,
the last bar flashes accompanied by an audible
signal.
You have approximately 5 litres remaining.
When the frequency of the flashing increases,
you have approximately 3 litres remaining .
Fuel gauge
At least 5 litres must be added after
running out of fuel.
1
Monitoring

34
108_en_Chap02_ouvertures_ed01-2015
Locking the vehicle
Locking
F With the electronic key in the recognition zone, press one of the buttons on the front
door handles or press the button on the
boot sill.
th

e direction indicators flash once. If one of the doors or the boot is still
open or if the electronic key for the
Keyless
e
n
try and Starting system has
been left inside the vehicle, you are
warned by an audible signal and the
central locking does not take place.
If the electronic key is left inside the
vehicle after switching off the engine,
there is a continuous audible signal on
opening the driver's door. Never expose the electronic key to
extreme temperatures (below -20°C or
above +60°C); this could cause faults.
For reasons of safety and theft
protection, do not leave your electronic
key in the vehicle, even when you are
close to it.
It is recommended that you keep it on
your person.
If the vehicle is unlocked and no door
or the boot is opened, the vehicle will
lock again automatically after about
thirty


seconds.
Access

41
108_en_Chap02_ouvertures_ed01-2015
* Depending on version. Your vehicle may be fitted with an electrically operated fabric roof.
electric fabric roof*
Electric opening and closing
the roof is opened and closed by pressing
the control at the interior lamp, in the opening
direction 1 and in the closing direction 2.In order to maintain the state of charge
of the battery, it is recommended that the
roof be operated with the engine running
.
Operation of the roof is possible with
the ignition on and when driving.
Operation of the roof could cause
serious injuries: before operating the
roof, ensure that no occupant of the
vehicle or person outside the vehicle
could be subject to any risk related
to the movement of the roof and that
no object could inter fere with the
operation. During operation of the roof with just
the ignition on, starting the engine may
cause the roof to stop, depending on
the state of charge of the battery.
t
o
h

ave the roof continue the operation,
operate the control again after the
engine has started.
th

e asymmetric shape of the opening
control avoids closing the roof by
mistake.
Position of the roof
Position 0 : Roof completely closed.
Position 1 : Automatic stop position for the roof.
Position 2 : Roof completely open.
2
Access

42
108_en_Chap02_ouvertures_ed01-2015
Opening
F Briefly press the control in the opening direction to open the the roof in stages.
or
F

P
ress and hold the control in the opening
direction, until the manoeuvre is complete,
to open the roof completely.
P

ressing again stops the movement of the
roof.
Closing
F Briefly press the control in the closing direction to open the the roof in stages.
or
F

P
ress and hold the control in the closing
direction, until the manoeuvre is complete,
to close the roof to position 1 .
P

ressing again stops the movement of the
roof.
F
t
o c
lose the roof completely, press and
hold the control (between positions 1
and
0) until the roof locks closed.
th

e closing manoeuvre of the roof
could cause serious injuries: take
particular care with children.
If the roof does not close correctly:
-

c
heck that nothing is blocking the roof
(ignition off),
-

r
epeat the closing command (with the
engine running).
If the problem persists, contact a P
e

uge
Ot

dealer or a qualified workshop.
Operating fault
In the event of an electrical fault,
contact a Pe ugeOt dealer or a
qualified workshop.
Protection of the electric motors
used for opening and closing the
roof
Following repeated opening and closing of the
roof, the electric motors may become too warm
and no longer allow the roof to be opened or
closed. Allow the motors to cool down with no
operation of the roof for 10 minutes.
Access

46
108_en_Chap03_confort_ed01-2015
ensure that no person or object
prevents the seat slide from returning to
its initial position.
Check that the seat belt has reeled in
correctly so as to not impede access for
passengers to the rear seats.
Heated seat controlAccess to the rear seats
(3-door)
F Pull this control toward you to fold the seat
back and move the seat for ward.
When returning the seat to its initial position,
guide it back until the seat and backrest lock
into place.
Wit the engine running, the front seats can be
heated separately.
F

P

ress the control switch.


t
h

e indicator lamp comes on.
F

P

ressing the switch again stops the
heating.
the

temperature is controlled automatically.
the

seat heating function is deactivated about
two minutes after switching off the ignition.
t
o
r

eactivate it, switch the ignition on and press
the control switch again. Switch the seat heating off as soon
as it is no longer needed, as reducing
the vehicle's electrical current demand
reduces fuel consumption.
Comfort

53
108_en_Chap03_confort_ed01-2015
Heating
the heating system works only when the engine is running.F t
u
rn the control from blue
(cold) to red (hot) to adjust the
temperature to your wishes.
Temperature adjustment
Air flow adjustment
F turn the knob from position 1 to 4 to obtain the desired flow
o f a i r.
Avoid driving for too long without
ventilation (risk of misting and
deterioration of air quality).
Air distribution adjustment
Centre vent and side air vents.
Centre vent, side vents and footwells.
Footwells.
Windscreen and footwells.
Windscreen.
th

e air distribution can be varied by
placing the control in an intermediate
position.
3
Comfort