display Peugeot 208 2017 Owner's Guide

120
- Gear lever in position N.
- Brake pedal released.
-

T
hen gear lever in position A / D or M .
or
-
R

everse gear engaged.
Special cases: START invoked
automatically
As a safety measure and for your comfort,
START mode is invoked automatically when:
-
y
ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
air conditioning setting, etc.) where the
engine is needed for control of the system
or vehicle.
The ECO warning lamp flashes for a
few seconds, then goes off.
This operation is perfectly normal.
Manual deactivation
In certain circumstances, such as the need
to maintain a comfortable temperature in the
passenger compartment, it may be preferable
to deactivate the Stop & Start system.
The system can be deactivated at any time,
once the ignition is switched on.
This control switches off the Stop & Start
system.
-
Press.
-

T
he indicator lamp in the control remains
on.
-

A m
essage is displayed.
If you are stationary in Stop mode, the engine
restarts immediately.
Manual reactivation
- Press.
- T he indicator lamp in the control goes off.
-

A c
onfirmation message is displayed. If the engine is in STOP mode, it restarts
immediately.
The Stop & Start system is reactivated
automatically every time the ignition is
switched on.
Opening the bonnet
Before doing anything under the bonnet,
deactivate the Stop & Start system to
avoid the risk of injury related to an
automatic change to START mode.
Driving on flooded roads
Before driving in a flooded area, it is
strongly recommended that you deactivate
the Stop & Start system.
For more information on Driving advice
,
particularly on flooded roads, refer to the
corresponding section.
Driving

125
To register a speed higher than the previous
setting, there are two possibilities.
Without using the accelerator
- Press the SET + button.
A short press increases the speed setting by
1

mph (km/h).
Pressing and holding increases the setting in
steps of 5

mph (km/h).
By using the accelerator
- Exceed the saved speed until you reach the desired speed. -

P
ress the SET – or
SET + button.
To register a speed lower than the previous
setting:
-
P
ress the SET –
button.
A short press decreases the setting by 1 mph
(km/h).
Pressing and holding decreases the setting in
steps of 5 mph (km/h).
Switching the system off
- Place the thumbwheel at the 0 position:
cruise control mode is deselected. The
display returns to the total mileage recorder.
After switching off the ignition, all registered
speed settings are lost.
Operating fault
The registered speed is erased, then replaced
by three dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Changing the registered
speed setting
6
Driving

126
When changing the programmed
reference speed by means of a maintained
press, pay attention as the speed can
increase or decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
On a steep descent, the cruise control will
not be able to prevent the vehicle from
exceeding the registered speed.
The cruise control system cannot in
any circumstances replace the need
to obser ve speed limits or the need for
vigilance on the part of the driver.
To avoid any risk of jamming the pedals:
-
e
nsure that the mat is positioned and
secured to the floor correctly,
-

n
ever place one mat on top of another.Memorising speeds
This function allows speeds to be saved, which
can then be offered to set the two systems: the
speed limiter (to limit the speed of the vehicle)
or the cruise control (for a vehicle cruising
speed).
You can memorise up to five settings in the
system for each of the two systems.
By default, some speed settings are already
memorised.
With touch screen
This memorisation can be
configured from the menu Driving /
Vehicle .
F

Sel

ect the " Driving functions " tab.
F

Sel

ect the " Adjusting Speeds " function.
F

P

ress " ON" to activate the function.
F

Sel

ect the speed setting 1 to 5 that you want
to change.
F

S

elect the speed setting value you want to
change.
F

E

nter the new value using the numerical
keypad and confirm and click on " OK" to
confirm. As a safety measure, the driver must carry
out these operations when stationary.
Selection
To select a memorised speed:
F
P ress and hold the " +" or " -" button; the
system stops at the nearest memorised
speed.
F

P
ress and hold again the " +" or " -" button to
select another memorised speed.
A reminder of the speed and the state of the
system (on / off) is displayed in the instrument
panel.
Driving

128
The collision can be automatically avoided
if the speed difference between your
vehicle and the one ahead is not more
than 9 mph (15 km/h).
Above this threshold, the system will do
what is possible to avoid or reduce the
seriousness of the accident by lowering
the speed of impact.
Activation / Deactivation
It is possible to activate or
deactivate the Active City Brake
from the Driving / Vehicle menu.
The system state remains in memory when the
ignition is switched off.
Each subsequent time the ignition is switched
on, if the automatic emergency braking function
is deactivated, a temporary message will
be displayed indicating the speed threshold
(6

mph (10 km/h)). Please deactivate the Active City
Brake:
-

F
ollowing impact damage to the
windscreen close to sensor,
-
W
hen towing a trailer,
-
W
hen the vehicle is being towed,
-
W
hen the vehicle is about to cross a
toll barrier.
-
W
hen the vehicle is passing through
an automatic car wash,
Operating limits
Not detected are:
- Pe destrians, animals, motorcyclists,
cyclists.
-

F
ixed and non-reflective materials and
objects (cardboard box, wall, etc.).
-

V
ehicles not travelling in the same direction.
This system will not trigger or inter vene if the
driver:
-

p
resses the accelerator pedal firmly,
-

t
urns the wheel sharply (avoiding
manoeuvre).
-

m

ay stop the vehicle, holding the brakes on
for around 1.5

seconds when stationary to
allow the driver time to take back control of
the vehicle,
-

m

ay cause the engine to stall,
-

m

ay give rise to a pumping noise, due to the
pressurisation of the braking system.
Operating faults
Clean or clear any dirt, mist or objects (stickers,
leaves, etc.) from the top of the windscreen that
could obstruct the laser's field of vision. In the following cases, you should have the
system checked by a PEUGEOT dealer or a
qualified workshop:
-

T
he message "
Automatic braking system "
fault detected accompanied by an audible
signal indicates that a fault has been
detected.
-
F
ollowing an impact, the system is
automatically put out of ser vice, it no longer
works. The system detects the deployment
of airbags.
Do not attempt to remove, adjust or test
the sensor.
Only a PEUGEOT dealer or a qualified
workshop is able to work on the system.
Misting of the windscreen or accumulations
of snow on the bonnet could inter fere with the
operation of the laser. A message appears if
the laser is obstructed.
Use windscreen demisting and regularly clean
the area of the windscreen in front of the
sensor.
Be particularly vigilant when driving in poor
weather (very heavy rain, hail, fog, snow, etc.).
This is because braking distances increase
while the laser's calculation parameters remain
the same.
Driving

129
Parking sensors
The audible (front and rear) and visual (rear)
parking sensor system consists of proximity
sensors, installed in the rear bumper.
The sensors detect any obstacle which enters
its field of operation (person, vehicle, tree,
fence, etc.) behind the vehicle during the
manoeuvre.
Certain objects detected at the beginning of the
manoeuvre will no longer be detected at the
end of the manoeuvre due to the blind spots
between and below the sensors.
Examples: stake, roadworks cone or pavement
post.
Engage reverse gear
An audible signal confirms the activation of the
system on engaging reverse gear.
The proximity information is indicated by an
audible signal which becomes more rapid as
the vehicle approaches the obstacle.
When the distance between the rear of
the vehicle and the obstacle is less than
approximately 30

centimetres, the audible
signal becomes continuous.
Display in the screen
The audible signal is supplemented by the
display of bars in the screen which move
progressively nearer to the vehicle. When the
obstacle is very close, the "Danger" symbol is
displayed in the screen.
Stopping the assistance
Change to neutral.
Switching off the assistance
Press; the indicator lamp comes on.
The state of the system is stored when the
vehicle is switched off.
Resuming assistance
Press again; the indicator lamp goes off.
If this warning lamp comes on
when reverse gear is engaged,
accompanied by a message and/or
an audible signal, a fault has been
detected.
Contact a PEUGEOT dealer or a qualified
workshop.
6
Driving

130
In bad or wintry weather, ensure that the
sensors are not covered with mud, ice or
snow.
The system will be deactivated
automatically if a trailer is being towed or if
a bicycle carrier is fitted (vehicle fitted with
a towbar or bicycle carrier recommended
by PEUGEOT).
The parking sensor system cannot in
any circumstances replace the need for
vigilance on the part of the driver.Reversing camera
The reversing camera is activated automatically
when reverse gear is engaged.
The image is displayed on the touch screen.
The reversing camera function may be
supplemented with parking sensors.They are represented by lines marked "on
the ground" and do not allow the position of
the vehicle to be determined relative to tall
obstacles (for example: other vehicles, etc.).
Some deformation of the image is normal.
The blue lines represent the general direction
of the vehicle (the gap represents the width of
your vehicle except for the door mirrors).
The red lines represent a distance of about
30
cm beyond the edge of your vehicle's rear
b u m p e r.
The green lines represent distances of about 1
and 2 metres beyond the edge of your vehicle's
rear bumper.
The superimposed representation of guide
lines helps with the manoeuvre. The reversing camera cannot, in any
circumstances, replace the need for
vigilance on the part of the driver.
High pressure jet wash
When washing your vehicle, do not direct
the lance within 30
cm of the camera lens.
Opening the tailgate causes the display to
disappear.
Clean the reversing camera regularly
using a soft, dry cloth.
Driving

132
To activate the Park Assist system:
F
P
ress this control.
The indicator lamp in the control remains off.
A message is displayed in the screen.
F

S
elect the enter parking space manoeuvre.
The indicator lamp in the control comes on.
F

O
perate the direction indicator on the
parking side. F

M
ove for wards alongside the parking
space at a speed below 12
mph (20 km/h)
to measure it, keeping at a distance of
between 0.5 and 1.5
metres from the row of
parked vehicles.
Once measurement is complete, if the space is
large enough a message indicates that parking
is possible.
F

M
ove your vehicle for ward until a new
message is displayed. F

S
elect reverse and release the steering
wheel.
The assisted parking manoeuvre is in progress.
Without exceeding 5
mph (8 km/h), continue
the manoeuvres following the information given
by the "parking assistance" system, until the
end of manoeuvre message is displayed.
The indicator lamp in the control goes off,
accompanied by an audible signal.
Driving

133
The driver takes back control of the vehicle's
steering.
Exit from a parallel parking
space
F When you want to exit from a parallel parking space, start the engine.
With the vehicle stationary, to activate the Park
Assist system:
F

P
ress this control.
The indicator lamp in the control remains off.
A message is displayed in the screen. F

S
elect the exit parking space manoeuvre.

The indicator lamp in the control comes on.
F
O
perate the direction indicator on the exit
from parking side.
The direction indicator flashes throughout
the manoeuvre, whatever the position of the
control stalk.
F
S
elect a for ward or reverse gear then
release the steering wheel.
The assisted exit from parking manoeuvre is in
progress.
Without exceeding 3 mph (5 km/h), continue
the manoeuvres following the information given
by the "parking assistance" system, until the
end of manoeuvre message is displayed.
The manoeuvre is complete once the front
wheels of the vehicle are out of the parking
space.
The indicator lamp in the control goes off,
accompanied by an audible signal. The driver takes back control of the vehicle's
steering.
Deactivation
The system is deactivated automatically:
-
o n switching off the ignition,
-

i
f the engine stalls,
-

i
f no manoeuvre is per formed within
5
minutes of selecting the type of
manoeuvre,
-

a
fter a prolonged stop of the vehicle during
a manoeuvre,
-

i
f the road wheel anti-slip regulation (ASR)
is triggered,
-

i
f the speed of the vehicle exceeds the
stated limit,
-

w
hen the driver interrupts movement of the
steering wheel,
-

i
f the driver presses the Park Assist control,
6
Driving

134
If the system is deactivated during a
manoeuvre, the driver should reactivate it
manually to repeat the measurement.
-

i

f the vehicle cannot be properly positioned
(too many manoeuvres to get the vehicle in
or out),
-

i

f the driver's door is opened,
-

i

f one of the front wheels encounters an
obstacle.
A message is displayed in the screen.
The driver then takes back control of the
vehicle's steering.
Deactivation
The system is switched off automatically:
- w hen towing a trailer,
-

i
f the driver's door is opened,
-

i
f the speed of the vehicle is above 42 mph
(70


km/h).
To switch the system off for a prolonged period,
contact a PEUGEOT dealer or a qualified
workshop.
This warning lamp comes on in
the instrument panel and/or a
message appears on the screen,
accompanied by an audible signal
(short beep).
The indicator lamp flashes for a few seconds. If
the problem occurs while using the system, the
indicator lamp goes off.
These warning lamps indicate a fault
with the power steering.
Contact a PEUGEOT dealer or a qualified
workshop.
If the lateral distance between your vehicle
and the space is too great, the system may
not be able to measure the space.
Anything projecting beyond the dimensions
of the vehicle is not taken into account by
the Park Assist system during a manoeuvre.
In bad weather and in winter, ensure that
the sensors are not covered by road dirt,
ice or snow.
In the event of a fault, have the system
checked by a PEUGEOT dealer or a
qualified workshop.
Driving

135
Under-inflation detection
This system automatically monitors the tyre
pressure while driving.
The system monitors the pressure in all four
tyres, once the vehicle is moving.
It compares the information given by the
wheel speed sensors with reference values,
which must be reinitialised after ever y tyre
pressure adjustment or wheel change.
The system triggers an alert as soon as it
detects a drop in the pressure of one or more
tyres.
The tyre under-inflation detection system
does not replace the need for vigilance on
the part of the driver.
This system still requires you to check the
tyre inflation pressure (including the spare
wheel) every month as well as before a
long journey.
Driving with under-inflated tyres impairs
handling, extends braking distances and
causes early tyre wear, particularly in
adverse conditions (heavy loads, high
speeds, long journeys). Driving with under-inflated tyres
increases fuel consumption.
The tyre pressure specifications for your
vehicle can be found on the tyre pressure
label.
For more information on Identification
markings , including in particular the tyre
pressure label, refer to the corresponding
section.
Tyre pressures should be checked when
the tyres are "cold" (vehicle stopped for
1
hour or after a journey of less than
6
miles (10 km) at moderate speeds).
In the contrary case(hot), add 0.3
bar to
the values indicated on the label.
Under-inflation alert
This is indicated by fixed illumination
of this warning lamp, an audible
signal and, depending on the
equipment installed, a message
displayed on the screen.
F

R

educe speed immediately, avoid excessive
steering movements and sudden braking. The loss of pressure detected does not
always cause visible bulging of the tyre.
Do not be satisfied with just a visual
check.
F
I
n the event of a puncture, use the
temporary puncture repair kit or the spare
wheel (depending on equipment),
or
F
i
f you have a compressor, such as the one
in the temporary puncture repair kit, check
the pressures of the four tyres when cold,
or
F
i
f it is not possible to make this check
immediately, drive carefully at reduced
speed.
The alert is kept active until the system is
reinitialised.
The under-inflation alert can only be relied
on if the reinitialisation of the system has
been done with the pressures in the four
tyres correctly adjusted.
F

S
top the vehicle as soon as it is safe to do
so.
6
Driving