warning Peugeot 508 RXH 2012 Owner's Guide

3
101
!
i
Comfort








Warning triangle (stowing)

Before leaving your vehicle to set up and install the triangle, put on your high visibility vest.

The dimensions o
f the triangle (once folded) or its storage box must be:

-
A
: length = 438mm,
-
B: height = 56
mm,

- C: width = 38mm.
To use the triangle, refer to the manufacturer's
instructions.
) Turn the knob to remove the cover.)
Hold the cover and the triangle so that theydo not fall.


The location for a folded trian
gle is in the inner
trim panel of the boot lid.Placing the triangle in the
roa
d
Distance from your vehicle (in metres)
Road
Motorway
DayNight
50 m 80 m
150 m
These are the internationally recognisedvalues.
Use the triangle in line with local driving regulations.

The trian
gle is available as an accessory, contact a PEUGEOT dealer or a qualified
workshop.
) Place the triangle at a distance behindthe vehicle, as shown in the table below,
according to the type of road and the level
of ambient light.

116
i
Comfort
) Switch off the demist/defrost of the rear screen and door mirrors as
soon as it is no longer needed as lower current consumption results in reduced fuel consumption.


Front Demist -
Defrost






Rear screen
demist - defrost
The control button is located on theair conditioning system control panel. With manual air
conditioning
) Select this programme to demistor defrost the windscreen and side windows as quickly aspossible.
With dual-zone and quad-
zone di
gital air conditioning
Automatic visibility programme

Switching on
With Stop & Star t, when demisting has been switched on, the Diesel enginedoes not stop.


Switching off

The demist /defrost switches off automatically toprevent an excessive consumption of current.
)It is possible to stop the demist/defrost
operation before it is switched off automaticallyby pressing the button again. The indicator
lamp associated with the button goes off.
The system automatically manages the air conditioning, air flow and air intake, and provides optimum distribution towards the
windscreen and side windows.
Adjust the temperature control to quickly
demist/defrost the windows.
To switch it off, press the "visibility" button again, the warning lamp in the button goes off and the system rever ts to the previous settings.
)Select this programme to demist or defrost the windscreen andside windows as quickly as possible.
The system automatically manages the air conditioning, air flow and air intake, and
provides optimum distribution towards the
win
dscreen and side windows.
With the quad-zone digital air conditioning,
pressing this button deactivates and locks the
rear air conditioning. ) To stop the programme, press either the "visibility"button again or "AU TO "
, the
warning lamp on the button goes off and
the warning lamp in the "AU TO "buttoncomes on.
The system rever ts to the previous settings.
The rear screen demistin
g - defrosting can onlyoperate when the hybrid system is active.
)Press this button to demist/defrost the rear screen and, depending on version, the door mirrors. The indicator lamp associated with
the button comes on.

118
!
!
Driving
It is recommended that you do not apply the parking brake in very cold conditions (ice) and during towing
(recovery, ...). Deactivate the automatic functions and release the parking brakemanually.



Before leaving the vehicle, check that parking brake warning lamps in the instrument panel and the control lever Aare on, not flashing.

The electric parking brake combines
2 operating modes:- Automatic Application/ReleaseApplication is automatic when the engine
stops, release is automatic on use of the
accelerator (this mode is activated by
default), -Manual Application/ReleaseManual application of the parking brake is done by pulling control lever A.Manual release is done by pushing andreleasing the control lever, while pressing
the brake pedal.
When the driver's door is opened, there is an
audible signal and a message is displayed if the
brake is not applied.



Programming the mode

Depending on the country of sale of the vehicle,
the automatic application when the engine isswitched off and the automatic release whenyou press the accelerator can be deactivated. With the vehicle stationary, to apply the parking
brake whether the h
ybrid system is active or off,
pull
control lever A.


Manual application

Activation/deactivation is done via
the menu in the instrument panel
screen.
The parkin
g brake is then applied and released
manually. The application o
f the parking brake is confirmed by:


- illumination o
f the braking warning
lamp and of the Pwarning lamp in
the control lever A ,

- displa
y of a message.
When the driver’s door is opened with the
hybrid system active, there is an audible signal
and a message is displayed if the parking brakehas not been applied.








Electric parking brake

If this warning lamp comes on in the
instrument panel, the automatic mode
i
s deactivated.

4
119
!
i
Driving
With the ignition on or the hybrid system active,
to release the parking brake, pressthe brakepedal
, pull
then release control lever A.
The full release of the parking brake is confirmed by:


Manual release



- the braking warning lamp and of
the P warning lamp in the controllever Agoing off,

- displa
y of a message.
I
f you pull the control lever Awithout pressing
the brake pedal, the parking brake will not
be released and a message appears in the
instrument panel.If necessar
y, you can make a maximumapplicationof the parking brake. It is obtained
by means of a long pullon control lever A,
until you see a message and an audible signal is heard. Maximum application is essential:- in the case of a vehicle towing a trailer,
if the automatic functions are activatedbut you are applying the parking brake
manually,
- when the slope you are parked on may
vary (e.g. on a ferry, on a lorry, during
towing).
Maximum application

Before leaving the vehicle, check that parking brake warning lamps in the instrument panel and in the controllever A
are on fixed (not flashing).

Never leave a child alone inside thevehicle with the ignition on, as they could release the parking brake.



Automatic application,
engine off



- illumination of the braking warning
lamp and of the Pwarning lamp in
the control lever A ,

- displa
y of a message.
With the vehicle stationary, the parking brakeis automatically applied when the engine is
switched off. The application of the parking brake isconfirmed by:
In the case of towing, a loaded vehicleor parking on a gradient, make a maximum application of the parkingbrake then turn the front wheels towards the pavement and engage a gear whenyou park.
After a maximum application,the release time will be longer.

120
!
!
Driving
Automatic release
The electric parking brake releasesautomatically and progressively with the
movement of the vehicle,select position A, Mor Rthen press the accelerator.
Full release of the parking brake is confirmed by:


- the brakin
g warning lamp and of
the Pwarning lamp in the control lever Agoing off,

- displa
y of a message.


When stationary, with the hybrid systemactive, do not press the accelerator pedal unnecessarily, as you mayrelease the parking brake.
Before leaving the vehicle, check thatparking brake warning lamps in theinstrument panel and the control lever Aare on fixed, not flashing.



Immobilising the vehicle,
hybrid system active
With the hybrid system active and the vehicle
stationary, in order to immobilise the vehicle
it is essential to manually
apply the parkingbrake by pullingcontrol lever A.
The application of the parking brake isconfirmed by:
- illumination o
f the braking warning
lamp and of the Pwarning lamp in
the control lever A ,
- display of a message.
When the driver’s door is opened, a loud beep
is heard and a messa
ge is displayed if the
parking brake has not been applied.

Particular situations

In cer tain situations (e.g. star ting the engine),
the parking brake can automatically alter itsforce. This is normal operation.
To advance your vehicle a few centimetres
without star ting the engine, but with the ignition
on, press on the brake pedal and release the
parking brake by pushing then releasingcontrol lever A
. The full release of the parkingbrake is confirmed by the warning lamps in
the control lever Aand in the instrument panel going off and display of a message.
If a parking brake fault occurs while applied
or
if the battery runs flat, an emergency release is
always possible.
In order to ensure correct operation and
so your safety, the number of successive
application/release operations of the parkin
g
brake is limited to eight.
In the event of abuse, you are aler ted by a message and a warning lamp which flashes.

4
121
!
Driving

Emergency braking

In the event of a failure of the main servicebrake, a continuous pull on the control lever Awill stop the vehicle.
The dynamic stability control provides stability
during emergency braking.
If the emergency braking malfunctions,
a message will be displayed.
I
f a failure of the DSC system is
signalled by the lighting of this warning lamp, then braking stability is
not guaranteed.
In this event, stability must be assured by the
driver by repeating alternate "pull-release" actions on the control lever A .
Emergency parking brake release
)if your vehicle has one, take out the vehicle chock B
, located behind the rear seats. )On a slope, immobilise the vehicle byplacing a chock in front or behind one of
the front wheels, opposing the slope.
On level ground, immobilise the vehicle byplacing a chock in front or behind one of
the front wheels. In the event o
f fault with the electric parking
brake or a battery failure, an emergency
mechanical control can be used to manuallyrelease the parking brake.)
Immobilise the vehicle (or chock it if the brake pedal has not been released), with
the hybrid system active, place the gear lever in position M or R.)
Switch of the hybrid system, but leave the
ignition on. If you are unable to immobilise
the vehicle, do not operate this control and contact a PEUGEOT dealer or a qualified
workshop as soon as possible.

The emergency braking must only be used in exceptional circumstances.

122
!
!
Driving
)Fold the 2/3 par t of the rear seat for access
to the green cap.

For reasons of safety you must contact a PEUGEOT dealer as soon as possible to have the cap replaced.
Take care not to place anything dusty or
wet close to the cap.
With an emergency release,immobilisation of the vehicle is no longer be assured once the mechanical release has started and the mechanical tool cannot be used to apply the parkingbrake again.
Do not carry out any action on lever A
,or stop/star t the system while therelease tool is engaged.
Have it checked by a PEUGEOT dealer or a qualified workshop.
To r e - e ngage the electric parking brake(after correction of the fault or battery failure), make a long pull on the controllever Auntil the parking brake warninglamp (!) flashes in the instrument panel, then make a second long pull until this warning lamp comes on fixed (notflashing).
)
Turn the release tool clockwise
. For
reasons of safetyit is essentialto keep
turning until the stop is reached. The
parking brake is released.) Take care to refit the release tool in its
housing.) The operation of the parking brake is
reinitialised each time the ignition is switched off and on. If reinitialisation of the
parking brake is not possible, contact a
PEUGEOT dealer.) The application time may be longer than
with normal operation.
) Pierce the cap and inser t the release tool in
the tube.



The emergency braking should only be used in exceptional circumstances.

4
123
Driving

Operating faults

If the electric parking brake fault warning lamp comes on together with one or more of the warning lamps presented in these tables, place the vehicle in
a safe condition (on level ground, gear engaged) and contact a PEUGEOT dealer or a qualified workshop without delay.
SituationsConsequences
Display of the message "Parking brake fault" and of the following warning lamps:

- The automatic functions are deactivated.

- Hill start assist is not available.

- The electric parking brake can only be used manually.
Displa
y of the message "Parking brake fault" and of the following warning lamps:

- Manual release of the electric parking brake is only available by
pressing the accelerator pedal and releasing the control lever.

- Hill start assist is not available.

- The automatic functions and the manual application are still
available.
Displa
y of the message "Parking brake fault" and of the following warning lamps:

- The automatic functions are deactivated.

- Hill start assist is not available.

124
Driving
SituationsConsequences
To a p p l
y the electric parking brake:)
immobilise the vehicle and switch off the ignition. )
pull the control for at least 5 seconds or until application is complete.
)
switch on the ignition and check that the electric parking brake
warning lamps come on.
The application is slower than during normal operation.
To release the electric parking brake:) switch on the ignition.)
push the control lever and hold it for approximately 3 seconds then
release it.
If the braking warning lamp is flashing or if the warning lamps do not come on with the ignition on, these procedures will not work. Place the
vehicle on level ground and have it checked by a PEUGEOT dealer or a qualified workshop. and possibl
y
flashing

Display of the message "Parking brake fault" and of the following
warning lamps:

- Only the automatic application on switching off the engine and automatic release on acceleration functions are available.

- The manual application/release of the electric parking brake and theemergency braking are not available.
and possibl
y
flashing

Display of the message "Battery charge fault".


- You must stop as soon as it is safe to do so. Switch off and
immobilise
your vehicle (if necessary, place the a chock under a
wheel).

- Apply the electric parking brake before switching off the engine.

4
127
i
!
Driving
Manual gear changing
)
When the vehicle has moved off, select
position M to change to manual mode. )
Operate the +or -steering mounted control paddles.


At very low speed, if reverse gear is requested, this will only be taken intoaccount when the vehicle is immobilised(foot on the brake). A warning lamp appears in the instrument panel screen.

On sharp acceleration in manual mode,the gearbox will not change up unless the driver acts on the gear lever or thesteering mounted paddles.
Never select neutral N
while the vehicleis moving. Only engage reverse gear Rwhen thevehicle is immobilised with the brake pedal pressed. A
disappears and the
gears engaged
appear successively in the instrument
panel screen.
The
gear change commands are only carried
out if the engine speed permits. The internal combustion engine is still running. It is not necessary to release the accelerator
during gear changes.
When brakin
g or slowing down, the gearbox changes down automatically to permitacceleration in the correct gear. This selective
gear change mode enables you
to over take, for example, while still remaining in automatic mode.)Operate the + or -
steering mounted controlpaddle.
The gearbox engages the gear requested if the engine speed permits. A
is still displayed in theinstrument panel.
After a few moments without any action on
the controls, the gearbox resumes automaticcontrol of the gears.

Manual mode