fold seats Peugeot Bipper 2015 User Guide

68
Bipper_en_Chap04_ergonomie_ed02-2014
Returning the bench seat to its position
Put the bench seat in place in its front
anchorages in the fully folded position.
Fold the bench seat to the table position,
the front and rear feet of the seat lock
automatically.
Returning the bench seat to the sitting
position
lift the bench seat back.
take care not to trap the seat belts.
l
ock the seat back by pushing it fully
towards the rear.
t

he red indicator is no
longer visible.
Rear head restraints
the rear head restraints can be removed
and have two positions:
4 high, position for use,
4 low
, storage position.
to raise or lower a head restraint, pull it


forwards sliding it at the same time.
to remove it, place it in the high position,


push the lug and pull it forwards and
upwards.
to refit it, engage the head restraint rods


in the holes taking care to remain in the
centreline of the seat back.
Never drive with the head restraints


removed, they must be in place and
correctly adjusted.
Seats

69
Bipper_en_Chap04_ergonomie_ed02-2014
SPLIT REAR BENCH SEAT
the left-hand side (2/3) or right-hand
side (1/3) of this bench seat can be folded to
adapt the load space in the boot.
Table position
Press the head restraint and its lug
simultaneously to place the head restraint in
the low position.
u

nlock the seat back by pulling the
corresponding side control towards you.
t

he red indicator becomes visible.
Fold the corresponding seat back onto the
seat cushion.
Fully folded position
After placing the seat back in the table
position, pull the corresponding strap to
unlock the rear feet of the seat.
l

ift the seat fully to secure it in the fully
folded position.
Removing the bench seat
After placing the bench seat in the fully
folded position, lower the corresponding
transverse bar to unlock the front feet of the
seat.
l

ift the bench seat to detach it from its front
anchorages.
When driving, to secure the bench,
detach the red retaining strap, located
on the back of the bench seat cushion, and fix
one end to a front head restraint spindle and
the other end to the side of the seat cushion.
4
EASE OF USE and COMFORT
Seats

70
Bipper_en_Chap04_ergonomie_ed02-2014
Returning the bench seat to its position
Put the bench seat in place in its front
anchorages in the fully folded position.
Fold the bench seat to the table position,
the front and rear feet of the seat lock
automatically.
Returning the bench seat to the sitting
position
lift the bench seat back.
take care not to trap the seat belts.
l
ock the seat back by pushing it fully
towards the rear.
t

he red indicator is no
longer visible.
Repeat all of these operations for the other
part of the rear bench seat.
Seats

11 9
Bipper_en_Chap06_securite_ed02-2014
Good practice
the driver must ensure that all passengers
fasten their seat belts correctly .
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
t

he seat belts are fitted with an inertia reel
which automatically adjusts the length of the
strap to your size.
t

he seat belt is reeled in
automatically when not in use.
e

nsure that the seat belt has reeled in
correctly after use.
After folding or moving a seat, ensure that
the seat belt has reeled in correctly into its
compartment and that the buckle is ready to
accommodate the tongue.
t
he force limiter reduces the pressure of the
seat belt against the body of the occupants. t he equipment fitted to these seat belts is
operational when the ignition is switched on.
t

he inertia reels are fitted with a device
which automatically locks the strap in the
event of a collision or emergency braking or
if the vehicle rolls over.
t

he airbag warning lamp comes
on if the pretensioners are
deployed. Contact a P
euge O t

or a qualified workshop.
Depending on the nature and seriousness


of any impact, the pretensioning device may
be deployed before and independently of
inflation of the airbags. It instantly tightens
the seat belts against the body of the
occupants.
t

he deployment of the pretensioners is
accompanied by a slight discharge of
harmless smoke and a noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system. In order to be effective, a seat belt must:
-

restrain one person only
,
-

must not be twisted, check by pulling in

front of you with an even movement,
-

be tightened as close to the body as

possible.
t

he upper part of the seat belt should be
positioned in the hollow of the shoulder.
t

he lap part should be placed as low as
possible on the pelvis.
Do not interchange the seat belt buckles as
they will not fulfil their role completely. If the
seats are fitted with armrests, the lap part of
the seat belt should always pass under the
armrest.
Check that the seat belt is fastened correctly
by pulling the strap firmly. Recommendations for children:
-
use a suitable child seat if the passenger
is less than 12 years old or less than one
and a half metres tall,
-

never allow a child to travel on your lap,

even with the seat belt fastened.
For more information on child seats,
refer to the "Safety - Children on
board" section.
In accordance with current safety
regulations, for all work on your vehicle,
refer to a qualified workshop that has the
skills an equipment needed, all of which can
be provided by a P
euge O t
dealer
.
Have the seat belts checked regularly (even
after a minor impact) by a P
euge O t
dealer

or a qualified workshop: they must not show
any signs of wear, cutting or fraying and they
must not be transformed or modified.
Clean the seat belt straps with soapy
water or a textile cleaning product,
available from P
euge O t
dealers.
6
SAFETY
Seat belts