window RENAULT KANGOO 1997 KC / 1.G Electrical Equipment Workshop Manual

REAR AND INTERIOR LIGHTS
Fuses
81
FUSE BOX (passenger compartment)
This unit is located in the passenger compartment on the driver’s side.
Allocation of fuses (depending on equipment level).
Symbol Rating Description
10
15
30
30
30
20
15
15
15
15
10
25
25
20
15
15
25Instrument panel / Electric rear view mirrors/ Radio / Car phone
Courtesy light / Immobiliser
Consumer cut-out
Towing connection
Heated rear screen
Central door locking / Immobiliser
Front fog lights
Rear screen wash - wipe/
Reversing lights / Heated rear screen / Immobiliser
/ Lights on reminder buzzer
Front wash - wipe
Stop lights/ Instrument panel/ Airbag / Pretensioners
Anti-lock braking system (ABS)
Left hand electric window
Right hand electric window
Heated seats
Air conditioning
Radio / Cigar lighter / Car phone
Heating
81-2

REAR AND INTERIOR LIGHTS
Fuses
81
FUSE BOX (engine compartment)
12840S
Rating D7F F8Q E7J
1 30A Injection (238-279) - Injection (236)
2 30AFan assembly
(234)-Fan assembly
(234)
3 - 15A 5A - Injection (238) Injection (120)
4 15A -Engine functions
(238-250-450-927)-
5 15AFan assembly / ignition
(234-778)-Injection / ignition
(236-250-663-664)
6 70A - Preheating unit -
7 50A -Engine functions
(234-450-700)-
8 60A Dashboard (209-713) Dashboard (209-713) Dashboard (209-713)
9 60A Dashboard (104-209) Dashboard (104-209) Dashboard (104-209)
10 60A Electric windows / AC fan Electric windows Electric windows / AC fan
11 60A ABS ABS ABS
81-4

ELECTRICAL ASSISTANCE EQUIPMENT
Relay plate
POSITION AND ALLOCATION
(Most complete plate)
87
12965R
The relays are located above the fuse board at the
bottom of the dashboard. To reach them, open
the fuse box cover.
1 Lights on reminder buzzer
2 Front wiper timer
3 Flasher unit
4 Rear wiper timer
5 Heated rear screen relay
6 After ignition relay (electric window feed)
7 Front fog lights relay
87-1

ELECTRICAL ASSISTANCE EQUIPMENT
Relay plate
87
HEATED REAR SCREEN RELAY
Track Allocation
86 + relay control
85 Earth
30 + before ignition feed
87a Not used
87 Rear screen
95182R6
CONNECTION
NOTE : The track numbers are as for the compo-
nent.
AFTER IGNITION RELAY
(electric window feed)
95182R6
CONNECTION
NOTE : The track numbers are as for the compo-
nent.
Track Allocation
86 + accessories feed
85 Earth
30 + before ignition feed
87a Not used
87+ after ignition feed via relay (electric
window feed)
87
87a
30 86 8587
87a
30 86 85
87-4

WIRING
Heated rear screen
88
REPAIR OF THE FILAMENT
Clean the section to be treated locally to remove
all dust or grease, preferably using alcohol or a
glass cleaner, and wipe with a clean, dry cloth.
To obtain a regular line during the repair, apply
scotch adhesive tape on either side of the section
to be repaired, leaving the conducting line free.
Before applying the varnish, shake the bottle to
prevent the deposit of silver particles on the bot-
tom of the bottle.
The heated grid applied to the inner face of the
window may be accidentally cut, making the part
of the grid affected inefficient.
The exact point of the disconnection may be de-
termined by means of a voltmeter.
It is possible to repair such faults by applying the
heated rear screen varnish sold under Part
Number 77 01 421 135 (2 g pack).
DETERMINING THE EXACT POINT OF
DISCONNECTION WITH A VOLTMETER.
Switch on the ignition.
Switch on the heated rear screen feed.
DETECTION BETWEEN LINES B AND A
Connect the + wire of the voltmeter to the +
feed terminal of the rear screen.
Place the - wire of the voltmeter on a filament on
the - terminal side of the rear screen (line B). A
voltage approximately equal to battery voltage
must be obtained.
Move the - wire towards line A (arrow): the vol-
tage drops progressively.
If the voltage drops quickly the filament is cut at
that point (carry out this operation for each fila-
ment).
DI8814
DETECTION BETWEEN LINES C AND A
Connect the - wire of the voltmeter to the - termi-
nal of the rear screen.
Place the + wire of the voltmeter on a filament
on the + terminal side of the rear screen (line C);
essentially a voltage equal to the battery voltage
must be obtained.
Move the + wire towards line A (arrow); the vol-
tage drops progressively.
If the voltage drops quickly, the filament must be
cut at this point (carry out this operation for each
filament).
DI8815
88-1

WIRING
Airbags and seat belt pretensioners
88
PASSENGER AIRBAG MODULE
DESCRIPTION:
It is located in the dashboard, opposite the front
seat passenger.
It comprises:
- an inflatable cushion,
- two pyrotechnic gas generators and ignition
modules.
LOCATION
The components of the airbag module cannot be
separated.
98124S
NOTE : When it is triggered, the airbag opens the
plastic cover of the passenger airbag module.
Warning light on the instrument panel
shows the correct operation of the airbags and
the pretensioners.
NOTE : this system is operational after the ignition
has been turned on. A vehicle fitted with a pas-
senger’s airbag will be identified by a label in the
bottom corner of the windscreen on the passen-
ger’s side, and by the word "Airbag" on the dash-
board on the same side. Two additional labels on
the front window and the side of the dashboard
indicate that a child seat cannot be fitted to the
front seat. The passenger must not set his feet on
the dashboard or stick or pin objects to the dash-
board (refer to the Driver’s Handbook).
Each time the windscreen (or passenger door win-
dow) is replaced, remember to fit the labels sho-
wing that the vehicle is fitted with airbags.These
labels are available in a kit Part Number : 77 01
205 442.
REMINDER : The computer must be replaced after
the airbag has been triggered. Certain compo-
nents will lose their nominal characteristics after
the trigger energy has passed through them.
13060S
88-24