display RENAULT KANGOO 1997 KC / 1.G Foult Finding - Injection Repair Manual

JSA051.0
INJECTION
Fault finding - Checking conformity
17
D7F 710
engine -
55 tracks
Checks to be carried out during a road test.NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
6 Adaptive richness After
programming
phase
# 30
# 31 106 ≤ X ≤ 150
(average value after erasing
the memory : 128)
106 ≤ X ≤ 150
(average value after erasing
the memory : 128)
17-217

B76531.0
ELECTRONICALLY CONTROLLED HYDRAULIC SYSTEMS
Fault finding - Introduction38
ABS BOSCH
5.3
CONDITIONS FOR APPLICATION FOR THE TESTS DEFINED IN THIS FAULT FINDING
The tests described in this fault finding are only to be applied when the wording of the fault corresponds
exactly to the display on the XR25 kit.
If a fault is dealt with because there is a flashing bargraph, the conditions for confirming the existence of an
actual fault (and the need to apply the fault finding ) can be found in the "Notes" or at the beginning of the
bargraph interpretation.
If a bargraph is only interpreted when it is permanently illuminated, the application of the recommended
tests in the fault finding when the bargraph is flashing will not allow you to determine the origin of the
memorisation of this fault. In this case, only a test of the wiring and the connections of the component in
question must be carried out (the fault is simply memorised as it was not present at the time of testing).
NOTE : The ignition must have been switched off before the XR25 kit is used.
INDISPENSABLE TOOLING REQUIRED FOR OPERATIONS ON THE ABS SYSTEM
- XR25 kit.
- XR25 cassette n° 16 minimum.
Reminders :When there is intermittent fault memorisation, the ABS warning light will illuminate the next
time the vehicle is used until the car reaches 7.5mph (12 km/h). When the fault is memorised, a
counter relating to the fault is set at 40 . This value is reduced by one each time the ignition is
turned on if the fault is not present when the vehicle exceeds 7.5mph (12 km/h). When the
reading on the counter is equal to 1, it remains at 1 and the fault is not erased.
38-1

B76531.0
ELECTRONICALLY CONTROLLED HYDRAULIC SYSTEMS
Fault finding- Fiche XR2538
ABS BOSCH
5.3
SYMBOLISATION OF THE BARGRAPHS
- Of faults (always on coloured background) :
If illuminated, signals a fault on the product tested. The associated text
describes the fault.
This bargraph may be:
- Illuminated : fault present.
- flashing : fault memorised.
- Extinguished : fault absent or not found.
- Of status (always on white background) :
Bargraph is always on the upper right hand side
If illuminated, this signals the establishment of dialogue with the product computer
If it remains extinguished :
- The code does not exist.
- There is a fault in the XR25, the computer or the XR25/computer connection.
The representation of the following bargraphs indicates their initial status:
Initial status : (ignition on, engine stopped, without operator action).
Indefinite
illuminated when the function or condition specified on the fiche is
met
Extinguished
Illuminated extinguished when the function or condition specified on the fiche is
no longer met.
- Supplementary information:
Certain bargraphs have a *. Command*.., when the bargraph is illuminated, allows supplementary
information on the type of fault or status arising to be displayed.
or
38-3

B76531.0
ELECTRONICALLY CONTROLLED HYDRAULIC SYSTEMS
Fault finding - Conformity Check38
ABS BOSCH
5.3
Order of
operationsFunction to be checked Action Bargraph Display and Comments
1 XR25 dialogueD11
(selector on
S8)
2 Computer conformity#12
3
Operation of ABS warning
light- computer
initialisation check
IgnitionTwo second illumination of
warning light when ignition is
switched on (consult fault
finding if it remains illuminated
or if it does not illuminate)
4Acknowledgement that
brake pedal is not
pressed
5Acknowledgement that
brake pedal is pressedPress brake
pedal
Only carry out this conformity check after a complete XR25 check.NOTES
13
13
38-18

v0406.0
IMMOBILISER
Fault finding - Fault Chart (petrol version) 82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 2
CONT 1
A
yes
Refer to the chart for BG 7RH in the section
"Fault finding - Interpretation of XR25
bargraphs ".
no
Switch off the ignition and wait until the
immobiliser warning light flashes
(immobiliser active ).
Switch on the ignition and check on fiche
n° 56 whether
BG 7RH is illuminated .
Is
BG 7RH illuminated ?
yesRepair or replace the first key.
no
no Replace the decoder unit .
Check the key recognition function.
Try to start the vehicle with the second key.
Can the vehicle be started?
yes
B
yes
no Refit the antenna ring correctly.Is the antenna ring correctly mounted on the
ignition switch ?
Test the memory of the unit by entering #65
If "0" is displayed , test OK
If "1" is displayed ,fault .
Is "0" displayed on the screen ?
82-17

v0406.0
IMMOBILISER
Fault finding - Fault Chart (diesel version)82
AFTER REPAIRCarry out a conformity check.
Check that the immobiliser system is working correctly.
Erase fault memory G0**.
Fault Chart 2
CONT 1
A
yes
Refer to the chart for BG 7RH in the section
"Fault finding -Interpretation of XR25
bargraphs ".
no
Switch off the ignition and wait until the
immobiliser warning light flashes
(immobiliser active ).
Switch on the ignition and check on fiche
n° 56 if
BG 7RH is illuminated .
Is BG 7RH illuminated ?
yesRepair or replace the first key.
no
Check the key recognition function.
Try to start the vehicle with the second key.
Can the vehicle be started?
yes
B
yes
no Refit the antenna ring correctly.Is the antenna ring correctly mounted on the
ignition switch ?
no Replace the decoder unit .
Test the memory of the unit by entering #65
If "0" is displayed , test OK
If "1" is displayed, fault .
Is "0" displayed on the screen ?
82-28

v0406.0
IMMOBILISER
Fault finding - Checking conformity
82
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
1 Dialogue with XR25D56
(selector on
S8) n.56
2Code present
3Conformity of decoder
unitG70*
X X X
Part Number displayed in 2
sequences
4Interpretation of
bargraphs normally
illuminatedType of remote control :
- Illuminated for infrared
remote control.
- Extinguished for radio
frequency remote control.
Illuminated if equipped with
courtesy light timer.
Extinguished if not fitted with
courtesy light timer.
Illuminated for programming
with 2 keys.
Extinguished for programming
with 1 key.
1
2
2
3
If a fault bargraph illuminates, refer to the corresponding fault chart.NOTES
82-34

v0406.0
IMMOBILISER
Fault finding - Checking conformity
82
If a fault bargraph illuminates, refer to the corresponding fault chart.NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
5Configuration of the
computer -
petrol/dieselIlluminated if configured for a
diesel vehicle.
Extinguished if configured for
a petrol vehicle.
Command :
-G22*1* configuration for
petrol.
-G22*2* configuration
for diesel.
6 Forced protection
modeIlluminated only after entering
command G04* on the XR25.
Vehicle cannot be started as
long as
BG 9LH is illuminated.
7Immobiliser statusIlluminated if immobiliser
active : switch off the ignition
and wait approximately 10
seconds for the
BG 10LH to
illuminate.
Extinguished if immobiliser
inactive.
8Presence of the keyIlluminated when the ignition
is switched on if the key is
coded
(on condition that the vehicle
was protected before the
ignition was switched on,
immobiliser warning light
flashing).
NOTE : in normal operation,
bargraphs
8RH, 9 RH and 10 RH should be
illuminated together.
3
9
10
8
82-35

v0406.0
IMMOBILISER
Fault finding - Checking conformity
82
If a fault bargraph illuminates, refer to the corresponding fault chart.NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
9Reception of the key
codeIlluminated when the ignition
is switched on
if the key is coded and has the
correct format (on condition
that the vehicle was protected
before the ignition was
switched on, immobiliser
warning light flashing).
NOTE : In normal operation ,
bargraphs
8RH , 9RH and 10RH should be
illuminated together.
10 Valid key code Illuminated when the ignition
is turned on if the key is coded
and has the correct format and
code (on condition that the
vehicle was protected before
the ignition was turned on,
immobiliser warning light
flashing).
NOTE: In normal operation
bargraphs 8RH, 9RH and 10RH
should be illuminated
together.
11Reception of the
infrared signal from
the PLIP Illuminated for approximately
3 seconds if the infrared signal
is received by the decoder unit
via the infrared transmitter.
Illuminated for approximately
3 seconds if the infrared signal
received by the decoder unit
via the infrared transmitter is
the correct signal.
9
10
11
11
82-36

v0406.0
IMMOBILISER
Fault finding - Checking conformity
82
If a fault bargraph illuminates, refer to the corresponding fault chart.NOTES
Order of
operationsFunction to be
checkedAction Bargraph Display and notes
12Reception of door
lock/unlock
information from the
central door locking
buttonIlluminated when door
lock/unlock information is sent
by the central door locking
button and received .
Enter * 14 on the XR25 to
determine the information
received by the decoder unit :
- if * 14 = 0 door lock
information
- if * 14 = 1 door unlock
information
13Sending of
lock/unlock
information by the
decoder unit to the
locking micromotors.Illuminated when door
lock/unlock information is sent
by the decoder unit to the
locking micromotors.
Enter * 34 on the XR25 to
determine the information
sent by the decoder unit :
- if * 34 = 0 door unlock
information
- if * 34 = 1 door lock
information
(
NOTE: Ignore what is written
on fiche n° 56, XR25 cassette
n°16).
14Sending electric
window raise
informationNot used
15Reception of "doors
open" informationIlluminated if door open.
14
14
15
16
82-37