engine oil RENAULT KANGOO 1997 KC / 1.G General Information Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 1997, Model line: KANGOO, Model: RENAULT KANGOO 1997 KC / 1.GPages: 37
Page 16 of 37
DRAINING - FILLING
Power assisted steering
05
CHECKING THE LEVEL
POWER ASSISTED STEERING PUMP LEVEL
For topping up or filling, use ELF RENAULTMATIC
D2 or MOBIL ATF 220 oil
.
The level, when correct, should be visible between
the
MIN and MAX marks on the reservoir (1).
D7F - E7J - F8Q ENGINES
12422R1
05-4
Page 18 of 37
VALUES AND SETTINGS
Capacity - Grades
07
Components
When
draining
3,5
3.7 (1)
2.7
2.9 (1)E.E.C. country
Other countries
Capacity
in litres
(approx.)*
Grade
Petrol engine
(oil)
D7F
E7J
0 °C+30 °C-30 °C
+10 °C+20 °C-20 °C-10 °C
-15 °C+25 °C
CCMC-G415W40-15W50
ACEA A2-96/A3-9615W40-15W50
CCMC-G510W30-10W40-10W50
ACEA A2-96/A3-96 10W30-10W40-10W50
CCMC-G55W30
ACEA A2-96/A3-965W30
CCMC-G55W40-5W50
ACEA A2-96/A3-965W40-5W50
API SH 10W40
API SH 10W30
0 °C+30 °C-30 °C+10 °C+20 °C-20 °C-10 °C
-15 °C
API SH 5W30
API SH 15W40
* Check with dipstick
(1) After replacing the oil filter
07-2
Page 19 of 37
VALUES AND SETTINGS
Capacity - Grades
07
When
draining
4.7
5.2 (1)E.E.C. country
Other countries
Diesel engine
(oil)
F8Q
0 °C+30 °C-30 °C
+10 °C+20 °C-20 °C-10 °C
-15 °C+25 °C
CCMC-PD215W40
ACEA B2-96/B3-9615W40
CCMC-PD210W40
ACEA B2-96/B3-9610W40
CCMC-PD25W30
ACEA B2-96/B3-965W30
CCMC-PD25W40
ACEA B2-96/B3-965W40
API CF 10W30
0 °C+30 °C-30 °C+10 °C+20 °C-20 °C-10 °C
-15 °C+15 °C
API CF 15W40
API CF 10W40
* Check with dipstick
(1) After replacing the oil filter
Components
Capacity
in litres
(approx.)*
Grade
07-3
Page 28 of 37
VALUES AND SETTINGS
Tightening the cylinder head
07
METHOD FOR TIGHTENING THE CYLINDER HEAD
REMINDER:
In order to ensure that the bolts are correctly tightened, use a syringe to remove any oil which may be in the
cylinder head mounting holes.
All the cylinder head bolts must be systematically renewed after removal.
There is no cylinder head retightening operation.
Using engine oil, lubricate the threads and under the heads of the bolts.
27610
18594
3
D7F ENGINE
Preseating the gasket
Tighten all the bolts to 2 daN.m, then angle tigh-
ten to 90° in the order shown below.
Wait 3 minutes settling time.
Tightening the cylinder head:
- The cylinder head tightening is carried out in
stages and the following procedure is applied
successively to bolts 1-2 then 3-4, 5-6, 7-8 and 9
-10.
- Slacken bolts 1-2 until they are completely free.
- Tighten bolts 1-2 to 2 daN.m, then turn
through an angle of 200°.
- Repeat the slackening and tightening opera-
tions for bolts 3-4, 5-6, 7-8 and 9-10.
90775S
E7J ENGINE
Preseating the gasket
Tighten all the bolts to 2 daN.m, then angle tigh-
ten to 97° ± 2° in the order shown below.
27610
18594
3
90775S
Wait 3 minutes settling time.
Tightening the cylinder head:
- The cylinder head tightening is carried out in
stages and the following procedure is applied
successively to bolts 1-2 then 3-4, 5-6, 7-8 and 9
-10.
- Slacken bolts 1-2 until they are completely free.
- Tighten bolts 1-2 to 2 daN.m, then turn
through an angle of 97° ± 2°.
- Repeat the slackening and tightening opera-
tions for bolts 3-4, 5-6, 7-8 and 9-10
07-12