air condition RENAULT KANGOO 1997 KC / 1.G Sheet Metal Work Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 1997, Model line: KANGOO, Model: RENAULT KANGOO 1997 KC / 1.GPages: 255
Page 7 of 255
GENERAL
Engine and equipment
40
SPECIFIC BODYWORK FEATURES
Driver’s airbag
Passenger’s and driver’s airbag
Height adjustable front head restraint
Height adjustable and tiltable front head restraint
Rear parcel shelf
Luggage compartment net
Electric one touch windows
Heated electric rear view mirrors
Heated screen + timed windscreen wiper
Heated front seats
Front seat driver emergency exit
Rear bench seat 1/1
Rear bench seat 1/3 - 2/3
Cabin rack without stop
Headlining
Boot carpet
Parcel shelf luggage cover
Two front fog lights in bumper
(excluding F8 AC PAS)Pay load 600 kg
Pay load 625 to 710 kg depending on
engine/equipment
Pay load 800 kg
Glazed, sliding side door and rear opening doors
or glazed tailgate
Sliding side door (reflective glass)
Sliding side door (panel)
Rear door, panel
Rear door, glazed
Opening doors, panels
Opening doors, glazed
Tailgate
Opaque roof flap (excluding tailgate)
Glazed roof flap (excluding tailgate)
Fixed side window (meaning glazed side door)
Sliding side window
Fixed rear quarter panel (meaning the glazed
sliding side door )
Heat insulating windscreen (with air conditioning)
2 point rear centre seat belt
3 point rear centre seat belt
40-3
Page 43 of 255
LOWER STRUCTURE
Front end lower cross member
41A
PRB4121
INTRODUCTION
The replacement of this part is a basic operation
for a frontal impact .
The repair bench does not have to be used, on
condition that the side members have not been
affected by the impact.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- closure panel,
- towing ring,
- reinforcement on the front end lower cross
member (left hand side).
JOINTS WITH:
Cowl side panel
Front right wheel arch
Side member
Side member closure panel
PARTS CONCERNED (thickness in mm) :
1Front end lower cross member 1.5
2Bonnet hinge mounting 1.5
3Cross member partition reinforcement 1.5
4Cowl side panel 1
5Front right wheel arch 0.8
6Front side member, front section 1.5
7Side member closure panel 1.2
8Towing ring 2.5
41-1
Page 140 of 255
UPPER FRONT STRUCTURE
Plenum chamber
42G
PRB4214
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of :
- the wheel arch for a frontal impact,
- cowl side panel for a side impact.
This operation may be carried out partially (see
diagram and method below).
The Parts Department only provides chambers of
the (1) "air conditioning" type, as a result, the
closure panel must also be ordered (2).
In the following operation there are only descrip-
tions of the joints specific to the part concerned.
Information concerning other parts is dealt with
in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 Plenum chamber
Part assembled with :
- bonnet lock mounting,
- windscreen wiper motor mounting.
2 Partition closure panel.
JOINTS WITH :
Wheel arch
Injection unit and impact sensor mounting (left
hand side)
Bulkhead
Pillar lining (cowl side panel)
Windscreen aperture lower cross member
PARTS CONCERNED (thickness in mm) :
1Plenum chamber 1
2Shock absorber cup height adjuster 1
3Shock absorber cup 2
4Injection unit and impact sensor
mounting (left hand side) 2
5Bulkhead 1
6Cowl side panel (pillar lining) 1.5
7Windscreen wiper mounting 1.5
8Windscreen aperture lower cross
member 1.2
or
42-24