RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Manual PDF
Manufacturer: RENAULT, Model Year: 2013, Model line: KANGOO, Model: RENAULT KANGOO 2013 X61 / 2.GPages: 279, PDF Size: 1.29 MB
Page 71 of 279

17B-71
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF109
CONTINUED
2.DEFNOTESNone.
Check the presence and conformity of the fuel in the tank (see Test 19 Checking the conformity of the fuel).
Check the fuel supply circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol
2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the injectors (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector
rail - Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), MR
374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting),
Check the cylinder compressions.
Page 72 of 279

17B-72
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF120
PRESENT OR
STOREDENGINE SPEED SENSOR SIGNAL1.DEF: Inconsistent signal.
3.DEF: Interference.
4.DEF: Incorrect number of teeth.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present after starting the engine and under the following conditions:
– engine running at idling speed
Special note:
OBD warning light and level 1 fault warning light illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the crankshaft position sensor, component code 149
and of the injection computer connector, component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the crankshaft position sensor component code 149 between connections 3BL and
3BG on the injection computer connector, component code 120.
If the resistance of the crankshaft position sensor is not between 175 X 295 or 200 X 270 (F4R
engine of Duster) (between 0°C and 40°C), replace the crankshaft position sensor, component code 149 (see
MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Crankshaft position sensor: Removal - Refitting).
Check the insulation and continuity of the following connections:
–3BG between components 149 and 120,
–3BL between components 149 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the 58 teeth of the flywheel target are not damaged or broken.
Check that the target is securely mounted on the flywheel (see MR 388 (Logan and Sandero), MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 10A, Engine and
cylinder block assembly, Flywheel: Removal - Refitting): check the tightening torque and that there is no
angular play or movement in relation to the target shaft.
If the fault is still present, contact the Techline.
V42_V04_DF120/V42_V05_DF120/V42_V06_DF120/V42_V14_DF120/V42_V16_DF120/V42_V18_DF120
Page 73 of 279

17B-73
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF195
PRESENT OR
STOREDENGINE SPEED/CAMSHAFT SENSOR CONSISTENCY1.DEF: Inconsistent signal
NOTESPriority when dealing with a number of faults:
Deal with the following faults first:
– DF080 Camshaft dephaser circuit
– DF363 Camshaft dephaser
– DF457 Flywheel target
– DF120 Engine speed sensor signal
Conditions for application to a stored fault:
– The fault is declared present after the ignition has been switched on.
See the Wiring Diagrams Technical Note for Duster.
Run TEST 10 TDC sensor check.
Run TEST 20 Camshaft sensor check.
If the fault is still present, contact the Techline.
V42_V04_DF195/V42_V05_DF195/V42_V06_DF195/V42_V14_DF195/V42_V16_DF195/V42_V18_DF195
Page 74 of 279

17B-74
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF319
PRESENT OR
STOREDCAMSHAFT SENSOR CIRCUIT1.DEF: Plausibility
2.DEF: No signal.
NOTESPriority when dealing with a number of faults:
Deal with the following faults first:
– DF047 Computer supply voltage
– DF015 Main relay control circuit
– DF120 Engine speed sensor signal
– DF195 Camshaft sensor / engine speed consistency
– DF457 Flywheel target
– DF080 Camshaft dephaser circuit
– DF363 Camshaft dephaser
Conditions for application to a stored fault:
– The fault is declared present after the ignition has been switched on.
See the Wiring Diagrams Technical Note for Duster.
Check the condition and connection of the camshaft sensor connectors, component code 1265.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the internal resistance of the camshaft sensor. It must be greater than 100 k.
Check for +12 V on the camshaft sensor, component code 1265 on the following connection:
•3FB of component 1265.
Check the continuity, insulation and the absence of interference resistance on the following connection:
•3FB between components 1265 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
V42_V04_DF319/V42_V05_DF319/V42_V06_DF319/V42_V14_DF319/V42_V16_DF319/V42_V18_DF319
Page 75 of 279

17B-75
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF319
CONTINUED
Check the continuity, insulation and the absence of interference resistance on the following connections:
•3SX between components 1265 and 120,
•3SV between components 1265 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
Page 76 of 279

17B-76
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF342
PRESENT OR
STOREDMALFUNCTION INDICATOR LIGHT CIRCUIT1.DEF: Voltage too low.
2.DEF: Voltage too high.
NOTESConditions for application to a stored fault:
– The fault is declared present after the ignition has been switched on.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Part 1:
Check that there are no other present or stored faults.
– If the OBD warning light is still lit, move on to Part 3.
– Switch the ignition on, then switch it off. If the OBD warning light does not illuminate for a few seconds
(permanently off), move on to Part 2.
Part 2:
Fit a test light. Switch the ignition on, then switch it off.
– If the test light does not illuminate for a few seconds (permanently off), move on to Part 3.
– If the test light illuminates only for several seconds and then goes out, replace the instrument panel, component
code 247 (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio
II F 6) or MR 374 (Kangoo VLL), Mechanical, 83A, Instrument panel, Instrument panel: Removal -
Refitting).
V42_V04_DF342/V42_V05_DF342/V42_V06_DF342/V42_V14_DF342/V42_V16_DF342/V42_V18_DF342
Page 77 of 279

17B-77
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF342
CONTINUED
Part 3:
Check the connection and condition of the connector of the injection computer, component code 120 and the
instrument panel, component code 247.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation, and the absence of interference resistance on the following connection:
For Logan, Sandero, Duster, Clio II F 6 and Kangoo VLL:
•137C between components 247 and 120.
For Thalia 2/Symbol 2:
•3FH between components 247 and 120.
– If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
– If the fault is still present, contact the techline.
Page 78 of 279

17B-78
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF358
PRESENT OR
STOREDINJECTOR CONTROL COMPUTERDEF: Internal electronic fault.
NOTESNone.
See Technical Note 6520 "LANDI RENZO EURO V LPG SYSTEM FAULT FINDING" (D4F734 engine on Logan
and Sandero) or Technical Note 6524 "Landi Renzo Euro V LPG system fault finding" (K4M616 engine on
Duster).
V42_V18_DF358
Page 79 of 279

17B-79V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF361
PRESENT OR
STOREDIGNITION COIL 1 - 4 CIRCUITCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present after starting the engine and under the following conditions:
– engine running at idling speed
Special note:
For CC.1 and CO, the OBD warning light and level 1 fault warning light illuminate.
For CC.0, the OBD warning light and level 2 fault warning light illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
The D4D and K7M engines are equipped with a quadruple ignition coil module.
The K4M engine is equipped with 4 "pencil" type coils.
D4D and K7M engines
Check the cleanliness and condition of the injection computer connector, component code 120 and of the coil
connector, component code 778.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3CV or 3CZ (for Clio II F 6) between components 120 and 778,
–3CW or 3CV (for Clio II F 6) between components 120 and 778.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the ignition on, check the supply of the ignition coil, component code 778 using a test light on connection 3NA.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–3NA between components 1047 or 1016 (for Clio II F 6) and 778.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_DF361/V42_V05_DF361/V42_V06_DF361/V42_V14_DF361/V42_V16_DF361/V42_V18_DF361
Page 80 of 279

17B-80V2 MR-376-X76-17B050$082.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
DF361
CONTINUED
K4M engine
Check the cleanliness and condition of the pencil coil no.1 connector, component code 1077, of the pencil coil no.4
connector, component code 1080 and of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3CZ or 3CE (for Kangoo VLL) between components 120 and 1077,
–3CV between components 1077 and 1080.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
With the ignition on, check the supply of the pencil ignition coils, component code 1077 and 1080 using a test light
on connection 3NA of the injection relay, component code 1047 (for Logan, Sandero, Duster), on connection 3NA
of the fuel pump relay, component code 236 (for Kangoo VLL) or on connection 3N of the fuel pump relay,
component code 236 (for Thalia 2/Symbol 2).
Check the insulation, continuity and the absence of interference resistance on the following connection:
–3NA between components 1080 and 1047 (for Logan, Sandero, Duster) or 236 for Kangoo VLL),
–3N between components 1080 and 236 (for Thalia 2/Symbol 2).
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.