sensor RENAULT KANGOO 2013 X61 / 2.G Petrol V42 Injection Manual PDF

17B-202V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR216SENSOR SUPPLY VOLTAGE NO. 2
PA R A M E T E R
DEFINITIONThis parameter indicates the supply voltage no. 2 of the sensors in Volts.
Conformity check: Engine stopped and the ignition on, or the engine running and the engine coolant temperature
> 80°C without electrical consumers.
The voltage of PR216 is approximately 5000 mV.
In the event of a fault, run fault finding on the charging circuit and consult the interpretation of DF012 Sensor
supply voltage no. 2.
V42_V04_PR216/V42_V05_PR216/V42_V06_PR216/V42_V14_PR216/V42_V16_PR216/V42_V18_PR216

17B-204
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
PR427AVERAGE PINKING SIGNAL
PA R A M E T E R
DEFINITIONThis parameter indicates the average pinking signal.
Conformity check with the engine running and engine coolant temperature > 80°C
This parameter varies according to the pinking status in the combustion chamber.
In the event of a fault, apply the interpretation of fault DF088 Pinking sensor circuit.
V42_V04_PR427/V42_V05_PR427/V42_V06_PR427/V42_V14_PR427/V42_V16_PR427/V42_V18_PR427

17B-207
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
PR446UPSTREAM O2 SENSOR HEATING RESISTOR
PA R A M E T E R
DEFINITIONThis parameter indicates the heating resistance of the downstream oxygen sensor in
Ohms.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C
The value must be  9  at 20°C.
V42_V04_PR446/V42_V05_PR446/V42_V06_PR446/V42_V14_PR446/V42_V16_PR446/V42_V18_PR446

17B-208
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
PR447DOWNSTREAM O2 SENSOR HEATING RESISTOR
PA R A M E T E R
DEFINITIONThis parameter indicates the heating resistance of the downstream oxygen sensor in
Ohms.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C
The value must be  9  at 20°C.
V42_V04_PR447/V42_V05_PR447/V42_V06_PR447/V42_V14_PR447/V42_V16_PR447/V42_V18_PR447

17B-209V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test, then check with the diagnostic tool.
PR448IGNITION ADVANCE
PA R A M E T E R
DEFINITIONThis parameter indicates the ignition advance in volts.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature > 80°C
The value must be  0° V with the ignition on and 4 V at idle speed.
In the event of a fault, apply the interpretation of fault DF120 Engine speed sensor signal.
V42_V04_PR448/V42_V05_PR448/V42_V06_PR448/V42_V14_PR448/V42_V16_PR448/V42_V18_PR448

17B-213V2 MR-376-X76-17B050$140.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
*TDC: Top Dead Centre
**GMV: fan assemblyTool
commandDiagnostic tool title Comments
RZ001 Fault memoryThis command is used to clear the faults stored in the computer.
RZ003 Engine adaptivesThis command enables a long engine start time.
RZ031 Throttle stop programmingThis command is used to reset the necessary system adaptives
if replacing the throttle valve.
RZ033Richness regulation
programmingThis command is used to reset the necessary system adaptives
if replacing the injectors.
RZ037Flywheel target
programmingThis command is used to reset the necessary system adaptives
if replacing the TDC* sensor.
RZ064Programming the level of
alcoholThis command is used to count the richness adaptive
programming necessary when replacing the injection computer.
AC005 Cylinder 1 injectorThis command is used to perform an audible check on injector 1.
AC006 Cylinder 2 injectorThis command is used to perform an audible check on injector 2.
AC007 Cylinder 3 injectorThis command is used to perform an audible check on injector 3.
AC008 Cylinder 4 injectorThis command is used to perform an audible check on injector 4.
AC015 Fuel pump relayThis command is used to check the fuel pump.
AC017Canister bleed solenoid
valveThis command is used to check the canister bleed solenoid
valve.
AC027 Motorised throttleThis command is used to check the motorised throttle.
AC038 Low speed GMV** relayThis command is used to check the low speed GMV** relay.
AC039 High speed GMV** relayThis command is used to check the high speed GMV** relay.
AC180Air conditioning
compressor relay controlThis command is used to check the air conditioning compressor
relay.
PETROL INJECTION
Fault finding – Command summary table

17B-214V2 MR-376-X76-17B050$140.mif
PETROL INJECTION
Fault finding – Command summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AC217Additional fuel circuit
solenoid valveThis command is used to check the additional fuel circuit
solenoid valve. Only on Flexfuel injection
AC224Additional fuel circuit pump
relay This command is used to check the relay of the additional circuit
pump. Only on Flexfuel injection
AC250 Heating resistor 1 relayThis command is used to activate the heating resistor no.1 relay.
AC251 Heating resistor 2 relayThis command is used to activate the heating resistor no.2 relay.
AC252 Heating resistor 3 relayThis command is used to activate the heating resistor no.3 relay.
SC001 Write saved dataUse this command after replacing or (re)programming the
computer (if the data has been saved using command SC003).
SC003 Save computer dataThis command enables the computer operating data, the engine
adaptives, to be recorded.
SC006Start OBD test: Catalytic
converterThis command is used to test the catalytic converter.
SC007 Run OBD test: O2 sensorThis command is used to test the O2 sensors.
SC061Oil change interval (OCS)
OxidationThis command is used to perform a test on the oil oxidation (see
Technical Note 6523A, Oil change interval (OCS) fault finding
for petrol and diesel engines)
VP010 Enter VIN.This command is used to enter the VIN.
VP036 Fuel supply inhibitedThis command is used to inhibit fuel supply to the engine.

17B-221
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 2 General appearance of engine compartment
Check the fan assembly
Check the air filter unit.
Check the inlet manifold air pressure sensor by running TEST 7 Air inlet pressure sensor check.
Check the air pipes.
Check the coolant temperature sensor by running TEST 15 Coolant temperature sensor check.
Check the injector rail.
Check the inlet manifold.
Check the oil filter.
Check the catalytic converter.
Check the exhaust manifold.
Check the accessories belt.
Check the dipstick.
If the fault is still present, contact the techline.
V42_V04_ALP2/V42_V05_ALP2/V42_V06_ALP2/V42_V14_ALP2/V42_V16_ALP2/V42_V18_ALP2

17B-230
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 11 Black smoke from the exhaust
Check the air filter unit.
Check the air pipes.
Check the air inlet temperature sensor by running TEST 6 Checking the air temperature sensor.
Check the coolant temperature sensor by running TEST 15 Coolant temperature sensor check.
Check the injector rail.
Check the injectors by running TEST 13 Checking the injectors.
Check the upstream oxygen sensor by running TEST 17 Checking the upstream O2 sensor.
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
If the fault is still present, contact the techline.
V42_V04_ALP11/V42_V05_ALP11/V42_V06_ALP11/V42_V14_ALP11/V42_V16_ALP11/V42_V18_ALP11

17B-231
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 12 Blue smoke from the exhaust
Check the oil.
Check the coolant temperature sensor by running TEST 15 Coolant temperature sensor check.
Check the spark plugs.
Check the ignition coil by running TEST 14 Checking the ignition coil.
Check the injectors by running TEST 13 Checking the injectors.
Check the oil filter.
Check the oil circuit.
Check the exhaust manifold.
Check the oil pump.
Check the pistons and piston rings.
Check the cylinder head.
Check the inlet and exhaust valves.
Check the rotating parts.
If the fault is still present, contact the techline.
V42_V04_ALP12/V42_V05_ALP12/V42_V06_ALP12/V42_V14_ALP12/V42_V16_ALP12/V42_V18_ALP12