power steering RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ESP Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2007, Model line: SCENIC, Model: RENAULT SCENIC 2007 J84 / 2.GPages: 85, PDF Size: 0.29 MB
Page 11 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 11V2 MR-372-J84-38C050$248_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
REPLACING THE COMPUTER
When replacing the computer/pump assembly, follow this procedure:
–switch off the ignition,
–replace the computer (see MR 364 Mechanical or MR 370 Mechanical, 38C, Anti-lock braking system,
Hydraulic unit),
–enter the VIN using command VP001,
–configure the tachometric index using command VP007,
–configure the vehicle parameters with command VP004.
If Vdiag 0B, 11 or 12:
–configure the vehicle speed at initialisation with command VP032,
–inhibit or authorise the automatic brake light illumination (depending on the country's legislation)
using commands VP021 "Inhibit automatic brake light illumination" or VP022 "Authorise automatic
brake light illumination",
–enter the most recent After Sales operation date using command VP006,
–perform a road test followed by a fault reading to confirm that the system is operating correctly.
REPLACING THE COMBINED SENSOR
When replacing the combined sensor, you must erase the programming of the ESP sensors with command RZ003 (if
available).
Command RZ003 "Programming ESP sensors" is only available on Vdiag 09, 0A, 0B, 11, 12. IMPORTANT
It is imperative to check that the parameters selected match the vehicle's description.
Note:
Run this command every time the electric power steering is removed and refitted, and each time the steering wheel
angle is calibrated in the electric power steering subgroup.
MR-372-J84-38C050$248_eng.mif
Page 14 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 14V2 MR-372-J84-38C050$372_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
Tool faultAssociated
DTCDiagnostic tool title
DF001 50CCComputer supply
DF006 501FFront left-hand wheel speed sensor circuit
DF007 503FRear left-hand wheel speed sensor circuit
DF017 50C3Computer
DF020 50C3Tachometric index programming
DF026 500FFront right-hand wheel speed sensor circuit
DF027 502FRear right-hand wheel speed sensor circuit
DF055 50C3Vehicle parameter programming
DF063 5046Wheel speed inconsistency
DF066 5180No injection multiplex signal
DF090 5041Front right-hand wheel target
DF091 5042Front left-hand wheel target
DF092 5043Rear right-hand wheel target
DF093 5044Rear left-hand wheel target
DF097 5188No automatic transmission multiplex signal
DF126 50F4Combined sensor signal plausibility
DF152 50E6Multiplex network
DF153 50C3Multiplex network
DF186 5182No instrument panel multiplex signal
DF187 50CEBrake light activation relay circuit
DF188 50C6Brake light switch circuit
DF189 50F4Combined sensor circuit
DF190 50F4Combined sensor
DF191 50C9ESP on/off button circuit
DF193 5180Invalid injection multiplex signals
DF194 5158Invalid electric power steering signals
DF195 5188Invalid automatic gearbox multiplex signals
DF196 5158No power-assisted steering multiplex signal
MR-372-J84-38C050$372_eng.mif
Page 45 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 45V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
DF126
PRESENT
OR
STOREDCOMBINED SENSOR SIGNAL PLAUSIBILITY
NOTESSpecial notes:
This fault means that the combined sensor signals are not consistent with the other
ESP sensors (steering wheel angle sensor and wheel speed sensors). If the fault
appears while the vehicle is being driven on a steep gradient, during a very tight turn
or while the vehicle is being transported on a lorry, train, boat, etc., with the engine
running, clear the fault and if possible check that the fault has disappeared by carrying
out a road test.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Check the connection and condition of the combined sensor connector.
Ensure that the sensor is properly fixed to the body in the right direction (arrow pointing to the front of the vehicle).
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of the
tyres.
Using the diagnostic tool, calibrate the steering wheel angle in the "Electric power steering" subgroup followed by
command RZ003 "ESP sensor programming" for Vdiag 09, 0A, 0B, 12 and 11 in the ABS/ESP.
Re-establish dialogue with the ABS/ESP computer, clear the computer fault memory, carry out a road test then
check again with the diagnostic tool.
If the fault is still present, adjust the axle assembly geometries. Adjust if necessary and use the diagnostic tool to
calibrate the steering wheel angle again in the "Electric power steering" subgroup, then run command RZ003 ESP
sensor programming for Vdiag 09, 0A, 0B, 12 and 11 in the ABS/ESP.
Carry out a road test.
If the fault is still present, replace the sensor.
AFTER REPAIRClear the computer fault memory. If the combined sensor has been replaced, erase the
ESP sensor programming (Vdiag 09, 0A, 0B and 11) with command RZ003 ESP
sensor programming.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF126 /ESPBOSCH_V09_DF126/ESPBOSCH_V0A_DF126/
ESPBOSCH_V0B_DF126 /ESPBOSCH_V11_DF126/ESPBOSCH_V12_DF126
MR-372-J84-38C050$496_eng.mif
Page 55 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 55V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF194
PRESENT
OR
STOREDELECTRIC POWER ASSISTED STEERING MULTIPLEX SIGNALS
INVALID
1.DEF : inconsistency
2.DEF : fault detected
NOTESSpecial notes:
Although it is stored in the computer, the ABS/ESP system is not faulty. The ESP is
deactivated due to unusable information from the electric power steering system. Run
fault finding on the electric power steering with the diagnostic tool.
Note:
The electric power steering does not always store these transient faults as quickly as
the ABS/ESP system.
If no fault is stored in the electric power steering computer memory, start the engine; if
no present fault is displayed, contact the Techline. Once the fault in the electric power
steering system has been repaired, clear the ABS/ESP computer fault memory.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present after starting the engine.
1.DEF
NOTESNone
Check the condition of the axle assemblies (impacts, damage, etc.) and the conformity and good condition of
the tyres.
Check the axle assemblies, adjust if necessary.
Calibrate the steering wheel angle in the electric power-assisted steering using the diagnostic tool.
Ensure that the combined sensor is properly fixed to the body in the right direction (arrow towards the front of
the vehicle).
If all the checks are OK, clear the computer fault memory and clear the ESP sensor programming (Vdiag 09, 0A,
0B, 12 and 11) using command RZ003 "ESP sensor programming".
Carry out a road test.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF194 /ESPBOSCH_V09_DF194/ESPBOSCH_V0A_DF194/
ESPBOSCH_V0B_DF194 /ESPBOSCH_V11_DF194/ESPBOSCH_V12_DF194
Page 56 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 56V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF194
CONTINUED
2.DEF
NOTESNone
Carry out fault finding on the electric power steering using the diagnostic tool and repair if necessary.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
Page 58 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 58V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF196
PRESENT
OR
STOREDNO ELECTRIC POWER ASSISTED STEERING MULTIPLEX
SIGNAL
NOTESSpecial notes:
Although the fault is stored in the computer, it is not caused by ABS/ESP components,
but it indicates that the ESP is deactivated due to an electric power steering frame
transmission fault. Run fault finding on the electric power steering.
Note:
The electric power steering does not always store these transient faults as quickly as
the ABS/ESP system.
If there is no stored fault in the electric power steering computer memory, start the
engine; if no present fault is displayed, contact the Techline. Once the fault in the
electric power steering system has been repaired, clear the ABS/ESP computer fault
memory.
Priorities when dealing with a number of faults:
Deal with faults DF152 and DF153 first, whether they are present or stored.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present when the engine is started up.
Check the condition and correct locking of the blue PEH connector on the UPC (Vdiag 44) or the grey CT1
connector on the UPC (Vdiag 48).
Carry out a multiplex network test and check the electric power steering system using the diagnostic tool. If the
fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF196 /ESPBOSCH_V09_DF196/ESPBOSCH_V0A_DF196/
ESPBOSCH_V0B_DF196 /ESPBOSCH_V11_DF196/ESPBOSCH_V12_DF196
Page 61 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 61V2 MR-372-J84-38C050$682_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
SETTINGS
PR001:
PR002:
PR003:
PR004:Front right-hand wheel speed.
Front left-hand wheel speed.
Rear right-hand wheel speed.
Rear left-hand wheel speed.
These parameters specify the speed in mph of each wheel of the vehicle.
PR005: Computer supply.
This parameter shows the + after ignition computer feed voltage in volts.
PR007: Longitudinal acceleration.
This parameter indicates the longitudinal acceleration of the vehicle in ms-2. It should be 0 when the
vehicle is stationary.
PR016: Lateral acceleration programming offset (Vdiag 09, 0A, 0B, 12 and 11).
This parameter gives the correction made by the ESP on the gross value of the lateral acceleration
sensor.
PR020: Vehicle speed at initialisation (Vdiag 0B, 12 and 11).
This parameter shows the vehicle speed sent to the multiplex network when the computer is initialised.
PR030: Tachometric index.
This parameter specifies the tachometric index entered in the computer for the tyres fitted to the vehicle.
PR033: Steering wheel angle.
This parameter gives the steering wheel angle in degrees. This signal is transmitted by the electric
power-assisted steering to the ESP via the multiplex network.
PR034: Yaw angle.
This parameter gives the yaw angle supplied by the dual sensor or combined sensor in ˚/s. It should
be 0 when the vehicle is stationary.
PR036: Transverse acceleration.
This parameter gives the lateral acceleration supplied by the dual sensor or combined sensor in g.
It should be 0 when the vehicle is stationary.
PR038: Vehicle speed.
This parameter specifies the vehicle speed in mph.
PR055: Number of teeth on the target.
This parameter shows the number of teeth on the target.
PR063: Vehicle parameters.
This parameter shows whether the configuration (VP004) corresponds correctly to the vehicle under
diagnosis.
PR064: Automatic ESP reactivation threshold (Vdiag 08, 09, 12 and 0B).
This parameter shows the automatic ESP reactivation threshold in mph (km/h) This parameter should
be 30 mph (50 km/h). If the value differs, use command VP023.
PR065: Yaw angle programming offset (Vdiag 09, 0A, 0B, 12 and 11).
This parameter shows the correction made by the ESP to the raw yaw sensor value.
PR066: Steering wheel angle programming offset (Vdiag 09, 0A, 0B, 12 and 11).
This parameter shows the correction made by the ESP to the raw EPAS steering wheel angle sensor
value.
MR-372-J84-38C050$682_eng.mif
Page 62 of 85
ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 62V2 MR-372-J84-38C050$744_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
STATUSES
CLEARING
Control
*csv: ET017: Brake pedal.
This status gives the position (depressed or released) of the brake pedal
ET023: ESP On/Off button
This status is used to check the ESP On/Off button operation. This status (pressed or released) is
checked by keeping the button pressed.
ET030: Automatic brake light illumination.
This status indicates whether automatic brake lighting is authorised or inhibited during CSV
(understeer control)*. The parameters of this status can be modified using commands VP021 and
VP022 according to the legislation in force in the country concerned.
RZ001: Fault memory.
This command is used for clearing the computer's stored faults.
RZ003: ESP sensor programming (Vdiag 09, 0A, 0B, 12 and 11).
This command resets the ESP sensor programming. Run this command every time work on the
electric power steering required programming of the steering wheel angle or after any operation on
the axle assemblies. Use this command when the combined sensor has been removed or replaced.
AC003:
AC004:
AC005:
AC006:Front left-hand wheel solenoid valves.
Front right-hand wheel solenoid valves.
Rear left-hand wheel solenoid valves.
Rear right-hand wheel solenoid valves.
These commands permit a check on the hydraulics of each wheel.
Raise the vehicle in order to be able to rotate the wheels, and check that they rotate freely.
Keep the brake pedal depressed to prevent the wheel being tested from being turned by hand
(do not brake so firmly that full braking power is reached).
Select and confirm the command for the wheel concerned (e.g. Front left-hand wheel solenoid valve,
etc.)
Turn the wheel concerned by hand; you should see it go through 5 locking/unlocking cycles.
AC013:Test wheel speed sensor feed (Vdiag 0A, 0B, 12 and 11).
This command is used to check that voltage pulses of approximately 12 V are detected by a
multimeter at the sensor connector terminals on the computer side. You must use command AC013
once only.
AC016:Pump motor test.
This command is used to test the pump motor control circuit. Select command AC016 Pump Motor
Test. The motor must run for 5 seconds.
AC187:Brake light on relay.
This command is for testing brake light activation by the ESP when controlling understeer during sharp
deceleration.
MR-372-J84-38C050$744_eng.mif
Page 82 of 85
38C-82
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP14 Erratic ESP regulation
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check that the four tyres on the vehicle are identical.
Using the diagnostic tool, you must ensure that the value of configuration PR063 "Vehicle parameters"
matches the definition of the vehicle undergoing diagnostics.
If necessary, run command VP004 Vehicle parameters using the diagnostic tool to define the appropriate
parameters for the vehicle type.
Check the connection and condition of the combined sensor connector.
Check that the orientation of the combined sensor on the body is correct and that it is correctly mounted.
Calibrate the steering wheel angle in the Electric power-assisted steering domain using the diagnostic tool.
Clear the computer's fault memory and clear the ESP sensor programming (Vdiag 09, 0A, 0B, 12 and 11) with
command RZ003 "ESP sensor programming".
Carry out a road test followed by another check with the diagnostic tool.
If the fault is still present, adjust the axle assembly geometries. Adjust if necessary and calibrate the steering
wheel angle again in the Electric power assisted steering domain using the diagnostic tool.
Clear the computer's fault memory and clear the ESP sensor programming (Vdiag 09, 0A, 0B, 12 and 11) with
command RZ003 "ESP sensor programming".
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP14 /ESPBOSCH_V09_ALP14/ESPBOSCH_V0A_ALP14/
ESPBOSCH_V0B_ALP14 /ESPBOSCH_V11_ALP14/ESPBOSCH_V12_ALP14BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
Page 83 of 85
38C-83
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
*ASR: Traction control
ALP15ESP warning light comes on with the "ASR* disconnected or off"
message when the current is switched on without pressing the
ESP disconnection button
NOTESConsult this customer complaint only if the "Service", "ABS" and "Brake" warning lights
are not lit.
After disconnecting the battery, it is probable that the electric power steering loses the steering wheel angle
sensor indexing (the electric power steering no longer sends the steering wheel angle signal to the ESP, which is
then disabled).
The ESP system is not faulty, no fault is present in the fault memory, the ESP warning light comes on and the
"ASR disconnected or off" message indicate this transient and reversible status.
To restore the electric power steering indexing and enable the ESP again, it is necessary to:
–switch on the ignition or start the engine (to obtain maximum steering assistance),
–turn the steering wheel slowly to full right lock, to full left lock, then return slowly to the centre point after going
slightly past it,
–the ESP warning light should go out and the message "ASR disconnected or off" should disappear,
–stop the engine and switch off the ignition,
–switch on the ignition, start the engine and see that the warning light no longer lights up.
If the warning light and the message reappear, start the procedure described above again.
If the operation fails again or if this customer complaint appears without the battery having been disconnected, run
fault finding on the electric power steering and repair accordingly.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP15 /ESPBOSCH_V09_ALP15/ESPBOSCH_V0A_ALP15/
ESPBOSCH_V0B_ALP15 /ESPBOSCH_V11_ALP15/ESPBOSCH_V12_ALP15BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12