RENAULT SCENIC 2007 J84 / 2.G Automatic Transmission Siemens TA2005 Workshop Manual

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -131V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP3
CONTINUED 1
Check the oil level.
Check the oil pressure using PR003 Oil pressure:
Warm engine with gearbox oil temperature between 65 and 90˚C.
Measure the line pressure under the 3 following conditions:
IMPORTANT
The vehicle must be stationary: handbrake on and brake pedal depressed, no accessories operating
(e.g.: air conditioning)
1engine speed idling:
Shift the gear lever to R, N and D, the pressure reading must be greater than 2.5 bars.
2engine speed at 1200 rpm:
–gear lever in R position, the pressure reading must be greater than 4 bars.
–gear lever in D position, the pressure reading in first gear must be greater than 5.5 bars.
3engine speed at 2200 rpm:
–gear lever in R position, the pressure reading must be greater than 11 bars.
–gear lever in D position, the pressure reading in first gear must be greater than 11 bars.
Do the recorded values correspond to the specified values?
Shift the gear lever into position D and monitor
PR007 Turbine speed when accelerating.Replace the pressure modulating solenoid valve
and the oil. Repeat the check after replacement.
If the fault is still present, replace the hydraulic
distributor and all the solenoid valves (see MR 364
Mechanical, 23A, Automatic transmission,
Hydraulic distributor (for Mégane II) and MR 370
Mechanical, 23A, Automatic transmission,
Hydraulic distributor (for Scénic II)).
Does the turbine speed change?

Replace the automatic transmission (see MR 364, Mechanical, 23A,
Automatic transmission, Removal-Refitting (for Mégane II) and MR
370, Mechanical, 23A, Automatic transmission, Removal-Refitting
(for Scénic II)).
A
YESNO
NOYES
B
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -132V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP3
CONTINUED 2
Refer to the procedure and the safety instructions for carrying out a setting point check on the torque converter.
Theoretical engine speed at setting point: 2300 ± 150 rpm
Is the value of the setting point wrong or is there an internal noise in the converter?
Carry out a road test, observing the engine speed
on the instrument panel and the information
displayed on the diagnostic tool (PR006 Engine
speed)Replace the torque converter, the lock-up solenoid
valve and the oil. If the oil is burnt, also replace the
hydraulic distributor and all the solenoid valves
(see MR 364 Mechanical, 23A, Automatic
transmission, Hydraulic distributor
(for Mégane II) and MR 370 Mechanical, 23A,
Automatic transmission, Hydraulic distributor
(for Scénic II)).
When replacing the torque converter, ensure that the
reaction shaft is securely attached to the hub of the
oil pump (flanged shaft).
Note:
A setting point which is too low may be due to a lack
of engine power. Does the engine speed change each time
there is a gear change?

The checks carried out have not provided any
evidence of a fault and the automatic
transmission appears to be working correctly.
If the vehicle does show the customer complaint
selected, continue with the entire fault finding
procedure.Replace the hydraulic distributor and all the solenoid
valves. (see MR 364 Mechanical, 23A, Automatic
transmission, Hydraulic distributor
(for Mégane II) and MR 370 Mechanical, 23A,
Automatic transmission, Hydraulic distributor
(for Scénic II)).
B
NO
NOYES
YESNO
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -133V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP4 Automatic transmission malfunctioning on gear changing
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
Automatic transmission malfunctions may be noted during gear changing without any fault being stored in the
computer.
These malfunctions may be linked to:
–connection faults (insulation: creates a fault, resistance) in the sequence solenoid valve control wiring
harnesses (EVS1 to EVS6).
Check the tightness and condition of the clips on all the solenoid valve control wiring connections from the
computer to each solenoid valve.
Use command AC024 Sequential actuators control to find any faults.
–Hydraulic distributor faults (hydraulic slide valve seizing, strainer/distributor seal) preventing the sequence
solenoid valves from working properly.
Check the oil's condition (colour, burnt or not) its level and pressure: increasing with engine/turbine speed.
–Loss of pressure when changing gear (clutch brakes/cylinder leaks)
Read the values of the following parameters (gear lever in position D or R: vehicle stationary and handbrake
applied) on the CLIP tool:
–PR003 Oil pressure,
–PR006 Engine speed,
–PR007 Turbine speed,
–PR138 Reference pressure,
–PR008 Computer feed voltage.
These parameters are associated with automatic transmission operation.
If one of the values is incorrect, note the fault it causes.
Replace the faulty part if necessary and carry out a check.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2005_V14_ALP04/DP0TA2005_V18_ALP04

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -134V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP5 Erratic gear changes
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
Run a multiplex network test (see 88B, Multiplex).
Check for the following parameters:
–PR135 Standard pedal position,
–PR136 Raw pedal position.
Carry out a road test using the diagnostic tool, making sure that status ET013 Gear engaged operates normally.
If the customer complaint occurs with the brake pedal released, check that status ET004 Brake light switch
(Closed) is NO.
If not, adjust the brake light switch and the brake pedal.
Make sure that the instrument panel display of the gear engaged matches the gear lever position.
Check the automatic transmission wiring harness (sequence solenoid valve control).
Replace it if necessary.
Check that the gear lever cable is working properly and adjust it if necessary.
Check that the multifunction switch is working correctly.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2005_V14_ALP05/DP0TA2005_V18_ALP05

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -135V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP6 Reversing lights do not work
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
Check:
–the condition of the fuses in the UPC.
–the condition of the bulbs.
–the condition of the bulb contacts. Repair if necessary.
–Check that the earth is present for the following connections:
●connection code MAQ of component 172,
●connection code MZ of component 173.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Switch off the ignition and disconnect the modular connector.
Switch on the ignition again and check for + 12 V after ignition feed on connection AP11 of component 485.
Switch off the ignition and check the continuity on the following connections, with the gear lever in position R:
●connection code H66P, between components 485 and 1337,
●connection code AP11, between components 485 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check that the gear lever cable is correctly adjusted and check the instrument panel display.
If the continuity is faulty, replace the multifunction switch.
Switch on the ignition.
With the gear lever in position "R", check for + 12 V after ignition feed on the following connections:
●connection code H66P between components 172 and 1337,
●connection code H66P, between components 173 and 1337.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2005_V14_ALP06/DP0TA2005_V18_ALP06

AUTOMATIC TRANSMISSION
Fault finding - Fault Finding Chart23A
23A -136V5 MR-372-J84-23A100$928.mif
SIEMENS TA2005
Vdiag No.: 14-18
ALP7 Oil present under vehicle
NOTESOnly refer to Customer complaints after carrying out a complete fault finding
procedure with the diagnostic tool and the conformity check.
Check the colour of the oil under the vehicle to determine the source of the leak (automatic transmission fluid is
red).
Clean the engine and gearbox.
Check the oil levels in the engine and gearbox.
Top up if necessary (see MR 364 Mechanical, 23A, Automatic transmission, Filling - levels (for Mégane II)
and MR 370 Mechanical, 23A, Automatic transmission, Oil change (for Scénic II)).
If there is no gearbox leak, look for a leak in the engine compartment.
If the leak is from the gearbox:
–Locate the source of the leak and carry out the necessary repairs.
–Replace any faulty parts.
–Check the oil level.
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
DP0TA2005_V14_ALP07/DP0TA2005_V18_ALP07

AUTOMATIC TRANSMISSION
Fault finding - Tests23A
23A -137V5 MR-372-J84-23A100$986.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Tests
Checking the gearbox output lever clearance TEST 1
MR-372-J84-23A100$986.mif

AUTOMATIC TRANSMISSION
Fault finding - Tests23A
23A -138V5 MR-372-J84-23A100$986.mif
SIEMENS TA2005
Vdiag No.: 14-18
TEST 1 Checking the gearbox output lever clearance
Normal lever:
Check the clearance in the ball detent of fixed 1st gear. There must be little or no lever clearance in this position.
Inverted lever:
Check the clearance in the ball detent of fixed 1st gear. There must be little or no lever clearance in this position.
DP0TA2005_V14_TEST01/DP0TA2005_V18_TEST01

AUTOMATIC TRANSMISSION
Fault finding - Tests23A
23A -139V5 MR-372-J84-23A100$986.mif
SIEMENS TA2005
Vdiag No.: 14-18
TEST 1
CONTINUED
Normal lever:
Check the clearance in the Park position. Clearance must be approximately 1.5 mm (measured at the ball joint).
Inverted lever:
Check the clearance in the Park position. Clearance must be approximately 1.5 mm (measured at the ball joint).