RENAULT SCENIC 2007 J84 / 2.G Automatic Transmission Siemens TA2005 Workshop Manual
Manufacturer: RENAULT, Model Year: 2007, Model line: SCENIC, Model: RENAULT SCENIC 2007 J84 / 2.GPages: 139, PDF Size: 0.43 MB
Page 101 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of statuses
23A
23A -101V5 MR-372-J84-23A100$580.mif
SIEMENS TA2005
Vdiag No.: 14-18
ET025
SEQUENCE SOLENOID VALVE 5 CONTROL
NOTESThere must be no present or stored faults.
This status displays "ACTIVE" when the gear engaged is "1" and "INACTIVE" when other gears are engaged.
Disconnect the computer. Check the cleanliness and condition of the connectors.
Check the continuity of the following connections:
●connection code 5DL, between components 119 and 754.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of component 754 between the following connections:
●connection code 5AU,
●connection code 5DL.
The value should be 40 Ω ± 2 at approximately 23 ˚C.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the resistance is greater than 50 Ω, check the wiring harness, computer connector and modular connector.
If the status is still not correct, use the interpretation of fault DF088 "EVS5 Sequence solenoid valve circuit".
AFTER REPAIRRepeat the conformity check from the start.
Make sure that shifting up and down through each gear works properly.
DP0TA2005_V14_ET025/DP0TA2005_V18_ET025
Page 102 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of statuses
23A
23A -102V5 MR-372-J84-23A100$580.mif
SIEMENS TA2005
Vdiag No.: 14-18
ET026
SEQUENCE SOLENOID VALVE 6 CONTROL
NOTESThere must be no present or stored faults.
This status displays "INACTIVE" with any gear engaged.
Disconnect the computer. Check the cleanliness and condition of the connectors.
Check the continuity of the following connections:
●connection code 5DM, between components 119 and 754.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of component 754 between the following connections:
The value should be 40 Ω ± 2 at approximately 23 ˚C.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the resistance is greater than 50 Ω, check the wiring harness, computer connector and modular connector.
If the status is still not correct, use the interpretation of fault DF112 "EVS6 Sequence solenoid valve circuit".
AFTER REPAIRRepeat the conformity check from the start.
Make sure that shifting up and down through each gear works properly.
DP0TA2005_V14_ET026/DP0TA2005_V18_ET026
Page 103 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of statuses
23A
23A -103V5 MR-372-J84-23A100$580.mif
SIEMENS TA2005
Vdiag No.: 14-18
ET097
MANUAL MODE
NOTESThere must be no present or stored faults.
This status indicates the gear lever position.
This status displays "ACTIVE" when the gear lever is in position "M", "M+" or "M-".
This status displays "INACTIVE" when the gear lever is in positions "P", "R", "N" or "D".
If the correct status is not displayed, use the interpretation of fault DF093 "Manual sequential controls circuits".
AFTER REPAIRRepeat the conformity check from the start.
Make sure that shifting up and down through each gear works properly.
DP0TA2005_V14_ET097/DP0TA2005_V18_ET097
Page 104 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of statuses
23A
23A -104V5 MR-372-J84-23A100$580.mif
SIEMENS TA2005
Vdiag No.: 14-18
ET123
ET124
ET125
MULTIFUNCTION SWITCH S2
MULTIFUNCTION SWITCH S3
MULTIFUNCTION SWITCH S4
NOTESThere must be no present or stored faults.
Multifunction switch contact S1 is not connected on this vehicle.
These statuses show the position of the multifunction switch for each gear lever position.
The switch status can be "OPEN" or "CLOSED" (see table below).
S2 S3 S4
POPEN CLOSED CLOSED
ROPEN OPEN OPEN
NCLOSED OPEN CLOSED
DCLOSED CLOSED OPEN
MCLOSED CLOSED OPEN
M+ CLOSED CLOSED OPEN
M- CLOSED CLOSED OPEN
If a status fails to function as specified, use the interpretation of fault DF009 "Multifunction switch in prohibited
position".
AFTER REPAIRRepeat the conformity check from the start.
Make sure that shifting up and down through each gear works properly.
DP0TA2005_V14_ET123/DP0TA2005_V18_ET123/
DP0TA2005_V14_ET124/DP0TA2005_V18_ET124/
DP0TA2005_V14_ET125/DP0TA2005_V18_ET125
Page 105 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of statuses
23A
23A -105V5 MR-372-J84-23A100$580.mif
SIEMENS TA2005
Vdiag No.: 14-18
ET127
LOWER SEQUENTIAL LEVER SWITCH
NOTESThere must be no present or stored faults.
This indicates the status of the lower sequential lever switch.
This status displays "ACTIVE" with the gear lever in position "M-".
This status displays "INACTIVE" with the gear lever in a position other than "M-".
Check the sequential lever supply on the following connections:
●check for + 12 V on connection AP43 of component 129,
●check for the vehicle earth on connection N of component 129.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the gear lever in position "M", measure the voltage of the following connections:
●check for the vehicle earth on connection 5H of component 129,
●check for the vehicle earth on connection 5FM of component 129.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If any of the measured values is + 12 V, replace the sequential lever.
If the values are 0 V, check that the gear lever positions match the instrument panel display.
If the correct status is not displayed, use the interpretation of fault DF093 "Manual sequential controls circuits".
AFTER REPAIRRepeat the conformity check from the start.
Make sure that shifting up and down through each gear works properly.
DP0TA2005_V14_ET127/DP0TA2005_V18_ET127
Page 106 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of statuses
23A
23A -106V5 MR-372-J84-23A100$580.mif
SIEMENS TA2005
Vdiag No.: 14-18
ET128
UPPER SEQUENTIAL LEVER SWITCH
NOTESThere must be no present or stored faults.
This indicates the status of the lower sequential lever switch.
This status displays "ACTIVE" with the gear lever in position "M+".
This status displays "INACTIVE" with the gear lever in a position other than "M+".
Check the sequential lever supply on the following connections:
●check for + 12 V on connection AP43 of component 129,
●check for the vehicle earth on connection N of component 129.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the gear lever in position "M", measure the voltage of the following connections:
●check for the vehicle earth on connection 5H of component 129,
●check for the vehicle earth on connection 5FM of component 129.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If any of the measured values is + 12 V, replace the sequential lever.
If the values are 0 V, check that the gear lever positions match the instrument panel display.
If the correct status is not displayed, use the interpretation of fault DF093 Manual sequential controls circuits.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2005_V14_ET128
Page 107 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of statuses
23A
23A -107V5 MR-372-J84-23A100$580.mif
SIEMENS TA2005
Vdiag No.: 14-18
ET157
GEAR LEVER UNLOCKING
NOTESThere must be no present or stored faults.
This status displays "ACTIVE" when the gear lever is locked and "INACTIVE" when the gear lever is unlocked.
Check the status with:
–Gear lever in position "P".
–Instrument panel displaying "P" for the gear lever position.
Depress the brake pedal; the message on the instrument panel: Depress the brake pedal disappears.
The status displays "INACTIVE" with the brake pedal depressed and gear lever unlocking permitted.
The status displays "ACTIVE" with the brake pedal released and the gear lever locked in position "P".
This status can only be checked with the gear lever in position "P".
If the correct status is not displayed, use the interpretation of fault DF095 "Selector lever lock electromagnet
circuit".
AFTER REPAIRRepeat the conformity check from the start.
Make sure that shifting up and down through each gear works properly.
DP0TA2005_V14_ET157/DP0TA2005_V18_ET157
Page 108 of 139
Fault finding - Parameter summary table23A
23A - 108V5 MR-372-J84-23A100$638.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR001Coolant temperature
PR003Oil pressure
PR004Gearbox oil temperature
PR006Engine speed
PR007Turbine speed
PR008Computer feed voltage
PR105Vehicle speed
PR118Gearbox oil pressure sensor voltage
PR123Calculated engine torque
PR124Accel. pedal position for downshifting
PR126Current turbine speed
PR128Engine/turbine speed difference
PR135Standard pedal position
PR136Raw pedal position
PR138Reference pressure
PR146Difference between reference and oil pressure
MR-372-J84-23A100$638.mif
Page 109 of 139
Fault finding - Interpretation of parameters23A
23A - 109V5 MR-372-J84-23A100$696.mif
SIEMENS TA2005
Vdiag No.: 14-18AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters
PR001
COOLANT TEMPERATURE
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Run a multiplex network test (see 88B, Multiplex).
If parameter PR001 Coolant temperature is absent, refer to the interpretation of the parameter (see MR 366
Megane, 17B, Petrol injection or 13B, Diesel injection).
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2005_V14_PR001/DP0TA2005_V18_PR001
MR-372-J84-23A100$696.mif
Page 110 of 139
AUTOMATIC TRANSMISSION
Fault finding - Interpretation of parameters23A
23A - 110V5 MR-372-J84-23A100$696.mif
SIEMENS TA2005
Vdiag No.: 14-18
PR003
OIL PRESSURE
NOTESThere must be no present or stored faults.
Immobilise the vehicle: handbrake on and brake pedal depressed.
Check the oil pressure values on the diagnostic tool:
–engine not running: pressure reading less than 0.2 bar.
–engine at idle speed (~ 820 rpm) and gear lever at D or R: pressure reading ~ 2.6 bar.
–engine speed ~ 1400 rpm and gear lever at D or R: pressure reading ~ 8.7 bar.
AFTER REPAIRRepeat the conformity check from the start.
DP0TA2005_V14_PR003/DP0TA2005_V18_PR003