key RENAULT SCENIC 2008 J84 / 2.G Electrical Equipment - Instrument Panel Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 63, PDF Size: 0.19 MB
Page 7 of 63
83A-7
MR-372-J84-83A000$126.mif
V8
83A
INSTRUMENT PANEL
Fault finding - System operation
Instrument panel functions (entry level and mid-range versions):
The instrument panel allows:
–display by needle gauge of the following information:
–Vehicle speed
–Rev counter
–Fuel gauge
–Engine coolant temperature
–Management of 20 warning/indicator lights
–Alphanumeric display of the following information:
–Total and trip mileage
–Oil level
–Messages (68 messages)
–Keyless vehicle messages
–Warning messages
–Management of a multifunction buzzer:
The buzzer is used for the following functions:
–Indicating the operation of the direction indicators.
–Signalling that the lights have been left on.
–Indicating that the driver's or passenger's seat belts are not fastened when driving.
–Indicating that a door or the tailgate is not correctly closed.
–Signalling that the handbrake is on.
–Indicating the low fuel warning.
–Indicating that a speed has been exceeded, for Arabian versions, where an overspeed warning
is legally required.
–Indicating to the driver that the automatic locking when driving has been activated/deactivated.
The following buzzers can sound:
–Side lights on
–Direction indicators
–Management and trip computer display:
–Trip meter
–Fuel consumed
–Average fuel consumption
–Instantaneous fuel consumption
–Fuel range in kilometres and miles
–Distance travelled in kilometres and miles
–Average speed
–Oil service interval in kilometres
–Oil service interval in time
–Programmed speed (if the cruise control and speed limiter feature is present).
–Instrument panel dimmer: when the lights are on, the brightness of the instrument panel can be adjusted
using a button located on the instrument panel.
–In the event that the childproof lock system is not working, the buzzer will sound and a warning message
will appear on the instrument panel.
In vdiag 08 (with program version 040B) and vdiag 0C, the instrument panel can manage a personalised oil service
interval (known as the OCS) by detecting premature oil wear (depending on the engine). If the engine has this oil
wear detection management function, the oil service interval will initially be increased. The oil service interval could
however decrease more quickly if a “severe” type of driving (urban driving, diving in traffic jams, etc.) is detected by
the injection computer. The instrument panel will display a message to request that an oil service be performed
quickly, without necessarily displaying a warning message beforehand.
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$126.mif
Page 9 of 63
83A-9
MR-372-J84-83A000$252.mif
V8
83A
INSTRUMENT PANEL
Fault finding - Configurations and programming
1. CONFIGURATIONS:
WARNING
Run a configuration read to ensure that the new configuration values are used by the system.
LC no. CF no. Configuration Note:
LC001 CF018Reserve capacityAllows the instrument panel to be
configured for switching the indicator
light on.
LC005 CF034 Body type
LC006 CF035Tank capacity
LC007 CF036Key/Card
LC008 CF037 Clock
LC011 CF038 Dimmer present
LC029 CF149 Gearbox typeIf the vehicle has an automatic or sequential
gearbox, check that the instrument panel
shows the gear selected.
If the vehicle is not equipped with an
automatic or sequential gearbox, check that
there is no "Check gearbox" message (this
message indicates the absence of the
automatic gearbox frames if the instrument
panel has been configured for an automatic or
sequential gearbox).
LC030 Vehicle typeValue defined by default: Mégane II
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
MR-372-J84-83A000$252.mif
Page 11 of 63
83A-11
MR-372-J84-83A000$252.mif
V8
INSTRUMENT PANEL
Fault finding - Configurations and programming83A
TDB ph2 (EG/MG)
Prog Version: 04xx
Vdiag No.: 08, 0C
2. PROGRAMMING:
A) Switch on the ignition.
B) Enter the VIN using command VP002 Enter VIN.
C) Program the mileometer using command VP010 Mileometer update.
Check by reading parameter PR009 Mileometer.
D) Enter the oil change frequency in kilometres using command VP006 Oil change frequency in km.
Refer to the information available on the Shared World Information database via RENAULT.NET
(on the maintenance programme page) to check the vehicle configuration.
Ignition on, engine off. Run command VP006 Oil change frequency in KM.
Enter the oil change interval in km.
Example of entry:
Using the CLIP numeric keypad,
enter 20 to display 20,000 km.
or
enter 30 to display 30,000 km.
LC no. CF no. Configuration Note:
LC060 CF002 Language settingCheck the language by using a message.
LC061 CF150 Cruise control/speed limiterIf the vehicle is equipped with a Cruise
Control-Speed Limiter function: check that the
cruise control or speed limiter indicator light
comes on when the cruise control/speed
limiter button is pressed.
LC064 CF158 Seat belt reminder buzzerThis function should only be inhibited on
authorised vehicles.
LC066 CF040 Particle filter
LC090 CF006 Vehicle speed signal systemIf the vehicle is equipped with ESP: check by
pressing the ESP OFF button that the Traction
control deactivated message appears.
If the vehicle is not equipped with ESP: check
that the ESP warning light does not come on
for 3 seconds when the ignition is switched
on.
LC106 CF198O.C.S. (vdiag 08 and program
version 040B and vdiag 0C)Refer to the information available on the
Shared World Information database via
RENAULT.NET (on the maintenance
programme page) to check the vehicle
configuration.
Page 49 of 63
83A-49
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V8 MR-372-J84-83A000$945.mif
INSTRUMENT PANEL
Fault finding - Fault finding chart83A
TDB ph2 (EG/MG)
Prog version: 04xx
Vdiag No.: 08, 0C
ALP 2 The fuel level indicator does not display full
NOTESThe fuel tank must be filled with the ignition switched off (advise the customer to remove
the key).
Ideally the customer must fill the tank with at least 15 litres.
See Wiring Diagram Technical Note for Scénic II.
Ask the customer if the tank is filled up under the
following conditions:
–the customer filled the tank up to the 3
rd cut-out
–the customer has changed filling station
–the customer filled the tank in a flat-level station (not
on a slope).
Did the customer fill the tank while observing all of
these conditions?Ask the customer to return just after
having filled the tank under the conditions
mentioned above.
NO
YES
A
TDB_V08_ALP2/TDB_V0C_ALP2