relay RENAULT SCENIC 2008 J84 / 2.G Engine Compartment Connection Unit User Guide

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-57V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
KEYLESS VEHICLE
SUB-FUNCTION: STARTING
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine stopped, + after ignition feed on.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
Reverse gearET004:Reverse gear
engagedYES
NOIn the event of a fault, refer to the
interpretation of status ET004.
Manual gearbox
lever positionET005:Manual gearbox
lever positionNOT IN NEUTRAL
NEUTRALNormal statuses.
UNAVAILABLE
INVALIDIn the event of a fault, refer to the
interpretation of status ET004.
Starting
conditions metET010:Starting
conditions metSTATUS 1
STATUS 2
STATUS 3In the event of a fault, consult the
interpretation for status ET010.
YESNormal status.
+ 12 V after
ignition feed
relay controlET003:+ 12 V after
ignition feed relay
control INACTIVE
ACTIVEIn the event of a fault, consult the
interpretation of fault DF032.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-59V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
FUNCTION: AIR CONDITIONING
SUB-FUNCTION: COLD LOOP
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine stopped, + after ignition feed on.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
Compressor
controlAC008:Compressor
controlYou should be able to hear
the compressor clutch
(stops the motor running).In the event of a fault, apply the
procedure for dealing with
command AC008.
Fan assemblyAC009:Low-speed fan
assemblyThis command is used to
activate the fan assembly
at low speed.In the event of a fault, apply the
procedure for dealing with
command AC009.
AC010:High-speed fan
assemblyThis command is used to
activate the engine cooling
fan at high speed.In the event of a fault, apply the
procedure for dealing with
command AC010.
Low-speed
engine fan
assembly relay
controlET014:Low-speed
engine fan
assembly relay
controlINACTIVE
ACTIVEIn the event of a fault, consult
the interpretation for status
ET014.
High-speed
engine fan
assembly relay
controlET013:High-speed
engine fan
assembly relay
controlINACTIVE
ACTIVEIn the event of a fault, consult
the interpretation for status
ET013.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check87G
87G-60V7 MR-372-J84-87G050$440.mif
UPC
Vdiag No.: 48, 4C
FUNCTION: WIPING
SUB-FUNCTION: WIPER POWER
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application conditions: engine stopped, + after ignition feed on.
FunctionParameter or Status
Check or ActionDisplay and Notes Fault finding
WiperAC005:Low-speed
windscreen wiperThis command is used to
activate the windscreen
wiper motor at low
speed.In the event of a fault, apply the
procedure for dealing with
commands AC005 and AC006.
AC006:High-speed
windscreen wiperThis command is used to
activate the windscreen
wiper motor at high
speed.
Windscreen
wiper protectionET002:Windscreen
wiper protectionINACTIVEIn the event of a fault, refer to the
interpretation for status ET002.
Windscreen
wiper park
positionET018:Windscreen
wiper park
positionPRESENT (if the wiper
is not active)
ABSENTIn the event of a fault, refer to the
interpretation of status ET018.
Headlight
washerAC013:Headlight washer
relayThis command is used to
activate the headlight
washers relay on the
right and left-hand side
alternately.In the event of a fault, apply the
procedure for dealing with
command AC013.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table87G
87G-64V7 MR-372-J84-87G050$495.mif
UPC
Vdiag No.: 48, 4CENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
Tool status Diagnostic tool title
ET002Windscreen wiper protection
ET003+ 12 V after ignition feed relay control
ET004Reverse gear engaged
ET005Manual gearbox lever position
ET010Starting conditions met
ET013High-speed engine fan assembly relay control
ET014Low-speed engine fan assembly relay control
ET018Windscreen wiper park position
ET023Alternator thermal fault
ET027Oil pressure contact
ET062UCH request to injection or Protection and Switching Unit
MR-372-J84-87G050$495.mif

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table87G
87G - 75V7 MR-372-J84-87G050$715.mif
UPC
Vdiag No.: 48, 4CENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Command summary table
Tool command Diagnostic tool title
AC001Main beam headlights
AC002Dipped headlights
AC003Side lights
AC004Front fog lights
AC005Low-speed windscreen wiper
AC006High-speed windscreen wiper
AC008Compressor control
AC009Low-speed fan assembly
AC010High-speed fan assembly
AC011Rear screen de-icer
AC013Headlight washers relay
AC014Alternator regulation
AC016Test electrical supply circuits
MR-372-J84-87G050$715.mif

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 86V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC013
HEADLIGHT WASHER RELAY
NOTESSpecial notes:
Check the condition and connection of fuse 21 (15A) on the Protection and
Switching Unit. Replace it if necessary.
The headlight washer pump operates if the dipped headlights are lit and the
windscreen washer switch is pressed and held.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the headlight washer pump component code 219 (tabs bent, broken or
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the condition and connection of the Protection and Switching Unit connector (tabs bent, broken, or
oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
To check that the pump is working properly, supply the pump's tracks directly in one direction and then the other.
If the pump does not rotate, replace it.
Check for + 12 V alternately on connection code 39C of the headlight washer pump connector.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–39A, between components 1337 and 219,
–39C, between components 1337 and 219.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.