airbag RENAULT SCENIC 2008 J84 / 2.G Engine Compartment Connection Unit Workshop Manual

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - System operation87G
87G-12V7 MR-372-J84-87G050$110.mif
UPC
Vdiag No.: 48, 4C
9 - Injection
The Protection and Switching Unit is involved in injection operation, relating to supplying the computer and its
sensors.
Supply malfunctions may lead to engine management customer complaints (rough idle, etc.).
10 - Fuse fault finding
The Protection and Switching Unit can detect the condition of its fuses and indicate faults using:
DF014 LEFT-HAND SIDE LIGHT CIRCUIT.
DF015 RIGHT-HAND SIDE LIGHT CIRCUIT.
DF016 LEFT-HAND DIPPED HEADLIGHT CIRCUIT.
DF017 RIGHT-HAND DIPPED HEADLIGHT CIRCUIT.
DF018 LEFT-HAND MAIN BEAM HEADLIGHT CIRCUIT.
DF019 RIGHT-HAND MAIN BEAM HEADLIGHT CIRCUIT.
DF020 FRONT FOG LIGHT CIRCUIT.
DF021 REVERSING LIGHT(S) CIRCUIT.
DF022 REAR SCREEN DE-ICER CIRCUIT.
DF023 FRONT WINDSCREEN WIPER CIRCUIT.
DF024 GAS COMPUTER SUPPLY.
DF025 AIRBAG/ELECTRIC POWER-ASSISTED STEERING SUPPLY.
DF026 AUTOMATIC TRANSMISSION SUPPLY.
DF029 STEERING COLUMN LOC/ENGINE MANAGEMENT SUPPLY.
DF030 AIR CONDITIONING COMPRESSOR SUPPLY CIRCUIT.
DF031 HEADLIGHT WASHERS SUPPLY CIRCUIT.
DF032 + 12 V RELAY SUPPLY CIRCUIT.
DF036 STEERING COLUMN LOCK SUPPLY CIRCUIT.
To carry out fault finding on the fuses, run command AC016 Test electrical supply circuits.
If a fuse is faulty, the associated fault becomes STORED.
Once the fuse has been replaced or the repair completed, run command AC016 Test electrical supply circuits
again to clear the fault.
Protection and Switching Unit Version
There are 4 Protection and Switching Unit versions:
–N1: vehicle with a 340 W fan assembly.
–N2: vehicle with a 460 W fan assembly.
–N3: vehicle with a 550 W fan assembly (external relay).
–N4: vehicle with 340 W, 460 W or 550 W fan assemblies + automatic transmission and/or LPG and/or with
headlight washers.

ENGINE COMPARTMENT CONNECTION UNIT
87G
87G - 15V7 MR-372-J84-87G050$275.mif
UPC
Vdiag No.: 48, 4CENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Fault summary table
Summary of faults on which fault finding can be performed by the Protection and Switching Unit.
(With corresponding design office codes).
Tool fault Associated DTC Diagnostic tool title
DF006 920E COMPUTER
DF007 9211 UPC - ALTERNATOR CONNECTION
DF009 9214 + AFTER IGNITION FEED CIRCUIT (Vdiag 4C only)
DF012 9210 ALTERNATOR
DF013 920F VOLTAGE REGULATION
DF014 9217 LEFT-HAND SIDE LIGHT CIRCUIT
DF015 9218 RIGHT-HAND SIDE LIGHT CIRCUIT
DF016 9215 LEFT-HAND DIPPED HEADLIGHT CIRCUIT
DF017 9216 RIGHT-HAND DIPPED HEADLIGHT CIRCUIT
DF018 921B LEFT-HAND MAIN BEAM HEADLIGHT CIRCUIT
DF019 921C RIGHT-HAND MAIN BEAM HEADLIGHT CIRCUIT
DF020 921D FRONT FOG LIGHT CIRCUIT
DF021 9226 REVERSING LIGHT(S) CIRCUIT
DF022 921E REAR SCREEN DE-ICER CIRCUIT
DF023 921A WINDSCREEN WIPER CIRCUIT
DF024 9222 GAS COMPUTER SUPPLY
DF025 9223 ELECTRIC POWER ASSISTED STEERING/AIRBAG
SUPPLY
DF026 9224 AUTOMATIC GEARBOX SUPPLY
DF027 9225 ACCESSORIES SUPPLY
DF029 9221 INJECTION/STEERING COLUMN LOCK SUPPLY
DF030 9219 CLIMATE CONTROL COMPRESSOR SUPPLY CIRCUIT
DF031 921F HEADLIGHT WASHER SUPPLY CIRCUIT
DF032 9227 +12 V RELAY SUPPLY CIRCUIT
DF033 9229 FAN ASSEMBLY SUPPLY CIRCUIT
DF034 9212 ALTERNATOR TYPE
DF035 9213 COMPUTER SUPPLY VOLTAGE
DF036 9220 STEERING COLUMN LOCK SUPPLY CIRCUIT
MR-372-J84-87G050$275.mif

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-22V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 4C
DF009
PRESENT
OR
STORED+ APC CIRCUIT
1.DEF: Permanent low level
2.DEF: Permanent high signal
NOTESSpecial note:
This fault only applies to Vdiag 4C.
Conditions for applying the fault finding procedure to present faults:
The fault is declared present after the ignition has been switched on.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the connection and condition of the LPG electric control unit connector, component code 997.
Check for a voltage on connection AP31 to the connector for the LPG electric control unit, component code 997.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the connection and condition of the multifunction switch, the reverse gear switch and the manual
gearbox neutral sensor/reversing lights, component codes 485, 155, and 1109.
Check for a voltage on connection AP11 to the connectors for the multifunction switch, the reverse gear switch
and the manual gearbox neutral sensor/reverse lights, component codes 485, 155, and 1109.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the connection and condition of the passenger compartment electric control unit, component code 645.
Check for a voltage on connection APCB to the connector for the passenger compartment electric control unit,
component code 645.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the connection and condition of the electric steering column lock, component code 1088.
Check for a voltage on connection AP15 to the connector for the electric steering column lock, component code
1088.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the connection and condition of the airbag/pretensioner electric control unit and the electric power-
assisted steering system, component codes 756 and 1232.
Check for a voltage on connection AP44 to the connectors for the airbag/pretensioner electric control unit and
the electric power-assisted steering system connectors, component codes 756 and 1232.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
AFTER REPAIRErase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V4C_DF009

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-45V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF025
PRESENT
OR
STOREDELECTRIC POWER ASSISTED STEERING/AIRBAG SUPPLY
CC.0: Short circuit to earth
CC.0
NOTESTo display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check the conformity of the fuse F10 (5A) for the Protection and Switching Unit.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–AP44 between components 1337 and 1232,
–AP44, between components 1337 and 756.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF025/USM_V4C_DF025