bulb RENAULT SCENIC 2008 J84 / 2.G Engine Compartment Connection Unit Workshop Manual

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Introduction87G
87G - 7V7 MR-372-J84-87G050$055.mif
UPC
Vdiag No.: 48, 4C
5. FAULT FINDING LOG
You will always be asked for this log:
–when requesting technical assistance from Techline,
–for approval requests when replacing parts for which approval is mandatory,
–to be attached to monitored parts for which reimbursement is requested. The log is needed for warranty
reimbursement, and enables better analysis of the parts removed.
6. SAFETY ADVICE
Safety rules must be observed during any work on a component to prevent any damage or injury:
–check that the battery is sufficiently charged (see TEST3 Battery status test),
–use the appropriate tools,
–do not touch the xenon bulbs.
–do not work on the COSLAD system when it is in operation, the voltage is greater than or equal to 20,000 V. IMPORTANT IMPORTANT
Any fault on a complex system requires thorough fault finding with the appropriate tools. The
FAULT FINDING LOG, which should be completed during the procedure, enables you to keep
track of the procedure which is carried out. It is an essential document when consulting the
manufacturer.
IT IS THEREFORE ESSENTIAL THAT THE FAULT FINDING LOG IS FILLED OUT EVERY TIME IT IS
REQUESTED BY TECHLINE OR THE WARRANT RETURNS DEPARTMENT.

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-26V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF014
PRESENT
OR
STOREDLEFT-HAND SIDE LIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the front left-hand side light bulb is sound.
Repair if necessary.
Check the condition and connection of the connector to the left-hand headlight, component code 227 (tabs bent,
broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth connection code MAS, for the left-hand headlight connector is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the Protection and Switching Unit 8-track connector AN (tabs broken, bent
or oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–LPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the left-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF014/USM_V4C_DF014

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-28V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF015
PRESENT
OR
STOREDRIGHT-HAND SIDE LIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the front right-hand side light bulb is sound.
Repair if necessary.
Check the condition and connection of the right-hand headlight, component code 226 (tabs broken, bent or
oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth connection code MAS for the right-hand headlight connector, component code 226 is
perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, component code
1337 (tabs broken, bent or oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–LPD, between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the right-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF015/USM_V4C_DF015

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-30V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF016
PRESENT
OR
STOREDLEFT-HAND DIPPED HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the left-hand dipped beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the left-hand headlight, component code 227
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth, connection code MAS for the left-hand headlight connector, component code 227 is
perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–CPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the left-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF016/USM_V4C_DF016

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-32V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF017
PRESENT
OR
STOREDRIGHT-HAND DIPPED HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the right-hand dipped beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the right-hand headlight, component code 226
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth on connection code MAS for the right-hand headlight, component code 226 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–CPD between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the right-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF017/USM_V4C_DF017

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-34V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF018
PRESENT
OR
STOREDLEFT-HAND MAIN BEAM HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the left-hand main beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the left-hand headlight, component code 227
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth, component code MAS for the left-hand headlight connector, component code 227 is
perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–RPG between components 1337 and 227.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the left-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF018/USM_V4C_DF018

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-36V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF019
PRESENT
OR
STOREDRIGHT-HAND MAIN BEAM HEADLIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the right-hand main beam headlight bulb is sound.
Repair if necessary.
Check the condition and connection of the connector for the right-hand headlight, component code 226
(tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth on connection code MAS for the right-hand headlight, component code 226 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connection:
–RPD between components 1337 and 226.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the fitting and switch on the right-hand headlight.
Repair if necessary or replace the light if it is faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF019/USM_V4C_DF019

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of faults87G
87G-38V7 MR-372-J84-87G050$330.mif
UPC
Vdiag No.: 48, 4C
DF020
PRESENT
OR
STOREDFRONT FOG LIGHT CIRCUIT
CO: Open circuit
CC.0: Short circuit to earth
CO
NOTESSpecial note:
To display this fault as present or stored, run the command
AC016 Electrical supply circuit test.
Use Wiring Diagrams Technical Note for Mégane II or
Scénic II.
Check that the front fog light bulbs are sound.
Repair if necessary.
Check the condition and connection of the 2-track connectors for the front fog lights, component code 176 and
177 (tabs broken, bent or oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check that the earth on connection code MAS for the front right-hand fog light, component code 176 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check that the earth on connection code MAS for the front left-hand fog light, component code 177 is perfect.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring otherwise replace the wiring.
Check the condition and connection of the 8-track connector AN for the Protection and Switching Unit,
component code 1337 (tabs bent, broken, oxidised).
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–8E between components 1337 and 177,
–8F between components 1337 and 176.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the fitting and switch for the front fog lights.
Repair if necessary or replace the light(s) if faulty.
If the fault is still present, contact the Techline.
AFTER REPAIRRun command AC016 "Electrical supply circuits test".
Erase the faults from the computer memory, switch the + after ignition supply off and
back on again and run another check using the diagnostic tool.
USM_V48_DF020/USM_V4C_DF020

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 76V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
AC001
MAIN BEAM HEADLIGHTS
NOTESSpecial notes:
Check the condition and connections of fuses 6 (10A) and 7 (10A) on the Protection
and Switching Unit. Replace them if necessary.
Check the condition and connections of the bulbs. Replace them if necessary.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the headlights, component codes 226 and 227 (tabs bent, broken or
oxidised).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth, connection code MAS for the headlights, component codes 226 and 227.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on headlight connection codes RPD and RPG whilst running the command.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, connection
code 1337 (tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–RPD, between components 1337 and 226,
–RPG between components 1337 and 227.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.
MR-372-J84-87G050$770.mif

ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands87G
87G - 77V7 MR-372-J84-87G050$770.mif
UPC
Vdiag No.: 48, 4C
AC002
DIPPED HEADLIGHTS
NOTESSpecial notes:
Check the condition and connections of fuses 3 (10A) and 4 (10A) on the Protection
and Switching Unit. Replace them if necessary.
Check the condition and connections of the bulbs. Replace them if necessary.
Use Wiring Diagrams Technical Note for Mégane II or Scénic II.
Check the condition and connection of the headlights, component codes 226 and 227 (tabs bent, broken or
oxidised).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check for earth, connection code MAS for the headlights, component codes 226 and 227.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for + 12 V on headlight connection codes CPD and CPG whilst running the command.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition and connection of the Protection and Switching Unit 8-track AN connector, connection
code 1337 (tabs broken, bent or oxidised).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the connector.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–CPD, between components 1337 and 226,
–CPG between components 1337 and 227.
If the connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact Techline.
AFTER REPAIRRepeat the conformity check from the start.