fuse RENAULT SCENIC 2008 J84 / 2.G Parking Distance Control Workshop Manual

PARKING DISTANCE CONTROL
Fault finding - Introduction
87F
87F - 5V4 MR-372-J84-87F000$066_eng.mif
Vdiag No: 04-08
4. FAULT FINDING PROCEDURE (continued)
Wiring check
Fault finding problems
Disconnecting the connectors and/or manipulating the wiring harness may temporarily remove the cause of a fault.
Electrical measurements of voltage, resistance and insulation are generally correct, especially if the fault is not
present when the analysis is made (stored fault).
Visual inspection
Look for damage under the bonnet and in the passenger compartment.
Carefully check the fuses, insulators and wiring harness routing.
Look for signs of oxidation.
Tactile inspection
While manipulating the wiring harness, use the diagnostic tool to note any change in fault status from stored to
present.
Make sure that the connectors are properly locked.
Apply light pressure to the connectors.
Twist the wiring harness.
If there is a change in status, try to locate the source of the fault.
Inspection of each component
Disconnect the connectors and check the appearance of the clips and tabs, as well as the crimping (no crimping on
the insulating section).
Make sure that the clips and tabs are properly locked in the sockets.
Check that no clips or tabs have been dislodged during connection.
Check the clip contact pressure using an appropriate model of tab.
Resistance check
Check the continuity of entire lines, then section by section.
Look for a short circuit to earth, to + 12 V or to another wire.
If a fault is detected, repair or replace the wiring harness.

PARKING DISTANCE CONTROL
87F
87F - 25V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF008
PRESENT
OR
STOREDCOMPUTER FAULT
1.DEF : Internal electronic fault
2.DEF : Internal electronic fault
3.DEF : Internal electronic fault
4.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault reappears present or stored after its has been cleared, the ignition is switched
on and off again and reverse gear is selected.
Special notes:
If the fault is present and is represented by 1.DEF or 2.DEF, the system operates in
defect mode (substitute values are used).
If the fault is present and characterised 3.DEF and the buzzer fails to sound when
shifting into reverse, contact your Techline.
1.DEF
2.DEF
NOTES None
After following the instructions, if the fault recurs, switch off the ignition and disconnect the parking distance control
computer supply fuse (see vehicle diagram).
Reconnect the fuse, switch the ignition back on, and perform a fault reading.
If the fault recurs, check the connections and condition of the parking distance control computer 16-track
connector (no damage to the connections).
Repair if necessary.
With the ignition switched off, disconnect the parking distance control computer 16-track connector to check
the conformity of the supplies and to check the insulation, continuity and the absence of interference
resistance on the following connections:
16-track parking distance control computer connector with 1 connector:
Track 1+ after ignition feed
Track 3earth
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF008/AAP_V08_DF008

PARKING DISTANCE CONTROL
Fault finding - Fault Finding Chart
87F
87F - 43V4 MR-372-J84-87F000$924_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Fault Finding Chart
ALP1 No dialogue with the computer
NOTESNone
Try the diagnostic tool on another vehicle.
Check:
–The connection between the diagnostic tool and the diagnostic socket (lead in good condition).
–The injection, engine and passenger compartment fuses.
Check for the + 12 V battery feed on track 16, for a + 12 V after ignition feed on track 1 and for earth on track 5
and on track 4 of the diagnostic socket.
Repair if necessary.
1 connector:
Switch off the ignition, and disconnect the parking distance control computer connector to check the insulation,
continuity and absence of interference resistance on the following connections:
Parking distance control computer connector
Track 1 + Before ignition (see vehicle diagram)
Track 3 Earth
Track 8 track 7 of the diagnostic socket (K line)
Repair if necessary (refer to vehicle wiring diagrams).
2 connectors:
Switch off the ignition, and disconnect the parking distance control computer 16-track connector to check the
insulation and continuity and ensure the absence of interference resistance on the following connections:
Parking distance control computer connector
Track 1 + Before ignition (see vehicle diagram)
Track 8 Earth
Track 12 track 7 of the diagnostic socket (K line)
Repair if necessary (refer to vehicle wiring diagrams).
AFTER REPAIRCarry out a complete check using the diagnostic tool.
AAP_V04_ALP1/AAP_V08_ALP1
MR-372-J84-87F000$924_eng.mif