display RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Service Manual

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -132
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -132V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre approval (continued 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre approval ET035:Rear left-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
FLAT
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET035 is not OK,
consult the fault finding
procedure for status ET035.
PR006:Rear left-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR006.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR022:Rear left-hand tyre
temperature- 40ºC normal that the temperature is
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -133
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -133V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre management
fr*: front,
rr*: rear.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre
management PR009:Fr* wheel low speed
recommended
pressure.
In barCheck that the values entered
are actually the recommended
ones (see MR 364 (Mégane II)
or MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
Otherwise, enter the
recommended pressures using
command VP005 Write
recommended pressures. PR010:Rr* wheel low speed
recommended
pressure.
PR012:Fr* wheel high speed
recommended
pressure.
PR011:Rr* wheel high
speed
recommended
pressure.
PR014:Left/right pressure
difference threshold0.5 bar
None. PR015:Low under-inflation
threshold- 0.4 bar
PR059:Puncture report
threshold- 0.6 bar
PR017:Cold over-inflation
threshold0.7 bar
PR018:Warm over-inflation
threshold0.8 bar

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -134
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -134V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre display
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre displayET039:STOP warning light
on request ACTIVE
INACTIVEACTIVE, if a puncture is
detected.
There is a buzzer
activation request for all
severity level 1
warnings (puncture).
The buzzer emits a
single beep when a fault
occurs.
ET016:Buzzer activation
requestINACTIVE
STATUS 1
STATUS 2
INCONSISTENCY STATUS 1: request for
buzzer activation when
a puncture is detected.
STATUS 2: request for
buzzer activation to
warn the driver that the
vehicle speed is too
high when the vehicle
has one or more
punctured tyres. This
information is only valid
on vehicles fitted with
PAX System tyres.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
LIGHTING FUNCTION
Sub-function: Lighting command
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Lighting
controlET081:Lighting switch
positionOFF
SIDE
DIPPED
MAIN BEAM HEADLIGHTS
HAZARD LIGHTS In the event of a fault,
refer to the
interpretation of status
ET081.
ET115:Request to switch
on lights by light
sensor PRESENT
ABSENTIn the event of a fault,
consult the
interpretation of status
ET115.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
ET113:Automatic lighting
button DEPRESSED
RELEASED In the event of a fault,
consult the
interpretation of
status ET113.
ET111:Front fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET111.
ET082:Rear fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET082.
ET085:Hazard warning
lights buttonDEPRESSED
RELEASED In the event of a fault,
refer to the
interpretation of
status ET085.
ET083:Left-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET083.
ET084:Right-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET084.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -136
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -136V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
WIPING FUNCTION
Sub function: Wiper control
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Wiper controlET077:Wiper stalk positionOFF
INTERMITTENT
LOW SPEED HIGH SPEEDIn the event of a fault,
refer to the
interpretation of status
ET077.
ET096:Wiper stalk
intermittent speed
ring position1
2
3
4In the event of a fault,
consult the
interpretation of
status ET096.
ET118:Rain sensor
sensitivity ring
position
ET114:Wiper request by rain
sensorPRESENT
ABSENTIn the event of a fault,
consult the
interpretation of
status ET114.
ET078:Windscreen washer
requestPRESENT
ABSENTIn the event of a fault,
refer to the
interpretation of status
ET078.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -137
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -137V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
WIPING FUNCTION
Sub-function: Wiper control (continued)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Wiper controlET080:Rear screen wiper
requestPRESENT
ABSENTIn the event of a fault,
consult the
interpretation of
status ET080.
ET097:Rear screen wiper
park positionPRESENT
ABSENTIn the event of a fault,
consult the status
interpretation ET097.
ET079:Rear screen washer
requestPRESENT
ABSENTIn the event of a fault,
refer to the
interpretation of status
ET079.
ET109:Reverse gear
engagedYES
NO In the event of a fault,
check the reverse gear
switch and its
connections.
ET108:Automatic gearbox
lever positionNOT IN NEUTRAL
P
NEUTRAL
REARIn the event of a fault,
consult the
interpretation of
status ET108.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -138
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -138V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
LIGHTING FUNCTION
Sub-function: Lighting power
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Lighting powerET112:Interior lighting
controlACTIVE
INACTIVENone

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -144
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -144V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET014
CONTROL POWER LEVEL
NOTESThere must be no present or stored faults.
Special note:
This status displays the power level.
NONE, no power supply.
TIMED, when a door is opened.
+ ACCESSORIES FEED, when the start button is pressed.
+ AFTER IGNITION FEED when starting or forced + after ignition feed.
In case of inconsistency, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET014/UCH_V48_ET014/ UCH_V4C_ET014/
UCH_V4D_ET014 /UCH_V4F_ET014/UCH_V50_ET014

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -146
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -146V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET016
BUZZER ACTIVATION REQUEST
NOTESThere must be no present or stored faults.
Special note:
Status ET016 is STATUS 1 or STATUS 2 if the SSPP buzzer is activated. A tyre is
punctured or there is a severe under-inflation.
ET016 is STATUS 1.
Request for activation of the buzzer linked to display of a puncture warning message on the instrument panel.
Adjust the pressures of the four tyres to the recommended pressures. Repair or replace the tyre if necessary.
ET016 is STATUS 2.
Request for buzzer activation to warn the driver that the vehicle speed is too high when the vehicle has one or more
punctured tyres.
This signal is only valid for vehicles fitted with runflat tyres.
Adjust the pressures of the four tyres to the recommended pressures. Repair or replace the tyre if necessary.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET016/UCH_V48_ET016/ UCH_V4C_ET016/
UCH_V4D_ET016 /UCH_V4F_ET016/UCH_V50_ET016

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -159
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87B
87B -159V9 MR-372-J84-87B000$473.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET032
ET033
ET034
ET035
CONTINUED
STEP 2
IMPORTANT:
Wait 1 minute and 30 seconds before checking the change of status.
–If the original status is: over-inflated or under-inflated
Consult ALP 52 "Adjust tyre pressure" message appears (the wheel concerned is highlighted on the
display) and ALP 56 "Adjust tyre pressure" message appears (2 wheels are highlighted on the display).
–If the original status is: puncture
Consult ALP 56 "Stop! Tyre puncture" message appears (the wheel is highlighted on the display).
–If the original status is: absent
Consult ALP 54 "Tyre sensor fault" message appears (wheel warning light disappears) and ALP 55 "Tyre
sensor fault" message appears (4 wheel warning lights disappear).
If the status does not change, replace the sensor on the wheel concerned by following the instructions and the
programming procedure for the four valve codes, SC002 Program 4 valve codes (see Configurations and
programming).
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.