ESP RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals EDC16C36 Repair Manual

13B-237V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET341IMMOBILISER CODE PROGRAMMED
STATUS DEFINITIONYES: This status indicates that the immobiliser code has been programmed.
NO: This status indicates that the immobiliser code has not been programmed.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
YESStatus ET341 is YES if dialogue is possible between the UCH computer and the
injection computer and if the key code is recognised.
Engine starting authorisation is only given if the code is correctly recognised by the
UCH computer and status ET003: Engine immobiliser is INACTIVE.
In the event of a fault (see 87B, passenger compartment connection unit,
conformity check).
NOStatus ET341 is NO if dialogue is not possible between the UCH computer and the
injection computer (status ET003 Engine immobiliser remains ACTIVE).
This fault may be caused by incorrect key programming or a lack of key programming.
In this case, refer to the UCH fault-finding note (see 87B, Passenger compartment
connection unit) and follow the key programming procedure.
If the key programming is not the cause, run a multiplex network test (see 88B,
Multiplexing) and check that dialogue between the UCH and the injection computer
is possible.
If dialogue is not established, contact Techline.
EDC16C36_V44_ET341/EDC16C36_V4C_ET341/EDC16C36_V48_ET341/EDC16C36_V50_ET341/EDC16C36_V54_ET341/
EDC16C36_V58_ET341
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58, 58

13B-238V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET405CLUTCH PEDAL SWITCH
STATUS DEFINITIONACTIVE: This status indicates that the clutch pedal is depressed.
INACTIVE: This status indicates that the clutch pedal is released.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
ACTIVEClutch pedal depressed.
Non-conformity of the brake signals and/or the clutch switch signals can cause the
engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
INACTIVEClutch pedal released.
Non-conformity of the brake signals and/or the clutch switch signals can cause the
engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
EDC16C36_V44_ET405/EDC16C36_V4C_ET405/EDC16C36_V48_ET405/EDC16C36_V50_ET405/EDC16C36_V54_ET405/
EDC16C36_V58_ET405
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-243V9 MR-372-J84-13B450$131.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET415
CONTINUED 3
STATUS 3
Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is no longer coupled to
the engine (clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with cruise control active
(ET042 Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is
depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed,
consult the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with an automatic transmission:
Test the multiplex network: check the configuration of the multiplex network in relation
to the vehicle's technical specification, especially the configuration of the automatic
transmission computer (see 88B, Multiplexing).
STATUS 4Cancel button pressed
The cruise control/speed limiter function is deactivated whenever the suspend button
is pressed.
Status ET415 becomes STATUS 4, when driving when:
– Either the cruise control is active, or
– the speed limiter is active
– and when the "0" button is pressed by the driver.
This action deactivates the Cruise control/Speed limiter.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 4 without pressing the 0 button, consult the
interpretation of status ET703 Cruise control/speed limiter buttons and run fault-
finding on the R/0 control button located on the steering wheel, to the right.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-249V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS DEFINITIONRESUME: R button pressed.
SUSPEND: 0 button pressed.
INCREASE: Increase button pressed.
DECREASE: Decrease button pressed.
INACTIVE: This status indicates that no button has been pressed.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
INACTIVEWhen that no button has been pressed.
In the event of a fault, consult the interpretation of status ET703.
SUSPEND'0' button pressed.
In the event of a fault, consult the interpretation of status ET703.
RESUMER button pressed.
In the event of a fault, consult the interpretation of status ET703.
EDC16C36_V44_ET703/EDC16C36_V4C_ET703/EDC16C36_V48_ET703/EDC16C36_V50_ET703/EDC16C36_V54_ET703/
EDC16C36_V58_ET703
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-253V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705BRAKE SWITCH NO. 1BRAKE SWITCH NO. 2
STATUS DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE: This status indicates that the brake pedal is released.
NOTESSpecial notes:
Only perform these tests if the statuses do not correspond with the system
programming functions.
Note:
Statuses ET704 and ET705 should change status at the same time. If they are
inconsistent, consult the interpretation of fault DF228 Brake signal.
Use the Mégane II ph2, Scénic II ph2 Technical Note wiring diagram.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
ACTIVEBrake pedal depressed.
A brake signal non-conformity may cause the engine to race during gear changes.
In the event of a fault, apply the interpretation of statuses ET704 Brake contact no. 1
and ET705 Brake contact no. 2.
INACTIVEBrake pedal released.
A brake signal non-conformity may cause the engine to race during gear changes.
In the event of a fault, apply the interpretation of statuses ET704 Brake contact no.1
and ET705 Brake contact no. 2.
EDC16C36_V44_ET704/EDC16C36_V4C_ET704/EDC16C36_V48_ET704/EDC16C36_V50_ET704/EDC16C36_V54_ET704/
EDC16C36_V58_ET704/EDC16C36_V44_ET705/EDC16C36_V4C_ET705/EDC16C36_V48_ET705/EDC16C36_V50_ET705/
EDC16C36_V54_ET705/EDC16C36_V58_ET705
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-254V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705
CONTINUED
Sensor electrical conformity
ACTIVE
or
INACTIVEIf the brake lights are working:
check the continuity and the absence of interference resistance on the following
connection:
– Connection code 5A between components 160 and 120/645/119.
If there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the status and conformity of the fuse for the brake lights.
– the conformity of the values in the following table:
Disconnect the switch and carry out the following checks:
for MEGANE II and SCENIC II with ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal
depressed)65G and SP17 5A and BPT
Replace the switch if the values obtained are not correct.
For MEGANE II and SCENIC II without ESP
Continuity between
connectionsInsulation between
connections
Switch engaged
(Brake pedal released)5A and BPT 65A and SP17
Switch released
(Brake pedal
depressed)65A and SP17 5A and BPT
Replace the switch if the values obtained are not correct.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58

13B-255V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET706
ET707
ET708
ET709
ET710
ET711
ET712
ET713
ET714
ET715STORED ENGINE STATUS NO. 1
STORED ENGINE STATUS NO. 2
STORED ENGINE STATUS NO. 3
STORED ENGINE STATUS NO. 4
STORED ENGINE STATUS NO. 5
STORED ENGINE STATUS NO. 6
STORED ENGINE STATUS NO. 7
STORED ENGINE STATUS NO. 8
STORED ENGINE STATUS NO. 9
STORED ENGINE STATUS NO. 10
STATUS DEFINITIONThese statuses indicate the engine status in the event of a regeneration failure when
driving.
NOTESSpecial notes:
For Vdiag 48:
Interpret these parameters only if DF312 Speed request is present or stored.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
This status indicates the engine status in the event of a regeneration failure when driving:
NONE, + AFTER IGNITION, RUNNING, STOPPED.
Each STATUS between ET706 and ET715 corresponds to the engine status during a regeneration failure for which
the mileage is saved by PR794 Stored regeneration failure No. 1 to PR803 Stored regeneration failure No. 10
(for example, PR797 Stored regeneration failure No. 4 is related to ET709 Stored engine status No. 4).
EDC16C36_V48_ET706/EDC16C36_V48_ET707/EDC16C36_V48_ET708/EDC16C36_V48_ET709/EDC16C36_V48_ET710/
EDC16C36_V48_ET711/EDC16C36_V48_ET712/EDC16C36_V48_ET713/EDC16C36_V48_ET714/EDC16C36_V48_ET715/
EDC16C36_V50_ET706/EDC16C36_V50_ET707/EDC16C36_V50_ET708/EDC16C36_V50_ET709/EDC16C36_V50_ET710/
EDC16C36_V50_ET711/EDC16C36_V50_ET712/EDC16C36_V50_ET713/EDC16C36_V50_ET714/EDC16C36_V50_ET715/
EDC16C36_V58_ET706/EDC16C36_V58_ET707/EDC16C36_V58_ET708/EDC16C36_V58_ET709/EDC16C36_V58_ET710/
EDC16C36_V58_ET711/EDC16C36_V58_ET712/EDC16C36_V58_ET713/EDC16C36_V58_ET714/EDC16C36_V58_ET715
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-257V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
* Regen: regeneration
ET742
ET743
ET744
ET745
ET746
ET747
ET748
ET749
ET750
ET751STORED REGEN. REQUEST STATUS No. 1
STORED REGEN. REQUEST STATUS No. 2
STORED REGEN. REQUEST STATUS No. 3
STORED REGEN. REQUEST STATUS No. 4
STORED REGEN. REQUEST STATUS No. 5
STORED REGEN. REQUEST STATUS No. 6
STORED REGEN. REQUEST STATUS No. 7
STORED REGEN. REQUEST STATUS No. 8
STORED REGEN. REQUEST STATUS No. 9
STORED REGEN. REQUEST STATUS No. 10
STATUS DEFINITIONStatuses ET742 to ET751 correspond to the causes for the regeneration request. They
are connected to parameters PR816 Stored regeneration start No. 1 to PR825
Stored regeneration start No. 10 which contains the stored mileage of the vehicle at
the start of the regeneration (for example, PR745 Store regeneration start No. 4 is
related to ET709 Store regen.* request status No. 4).
NOTESSpecial notes:
For Vdiag 48:
These statuses should only be interpreted for ALP11 Particle filter warning light
comes on too frequently.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
STATUS 1Request by weight of soot
Regeneration has been requested after the maximum weight of soot has been
reached and measured in the particle filter, without the particle filter warning light
coming on.
EDC16C36_V48_ET742/EDC16C36_V48_ET743/EDC16C36_V48_ET744/EDC16C36_V48_ET745/EDC16C36_V48_ET746/
EDC16C36_V48_ET747/EDC16C36_V48_ET748/EDC16C36_V48_ET749/EDC16C36_V48_ET750/EDC16C36_V48_ET751/
EDC16C36_V50_ET742/EDC16C36_V50_ET743/EDC16C36_V50_ET744/EDC16C36_V50_ET745/EDC16C36_V50_ET746/
EDC16C36_V50_ET747/EDC16C36_V50_ET748/EDC16C36_V50_ET749/EDC16C36_V50_ET750/EDC16C36_V50_ET751/
EDC16C36_V58_ET742/EDC16C36_V58_ET743/EDC16C36_V58_ET744/EDC16C36_V58_ET745/EDC16C36_V58_ET746/
EDC16C36_V58_ET747/EDC16C36_V58_ET748/EDC16C36_V58_ET749/EDC16C36_V58_ET750/EDC16C36_V58_ET751
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-258V9 MR-372-J84-13B450$132.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
* Regen: regeneration
ET742
ET743
ET744
ET745
ET746
ET747
ET748
ET749
ET750
ET751
CONTINUED
STATUS 2
Request by estimated weight of soot
Regeneration has been requested following an estimate of the maximum weight of
soot in the particle filter, without the particle filter warning light coming on.
STATUS 3Request by distance travelled
Regeneration has been requested because the distance travelled since the last
successful regeneration has reached the maximum authorised value (the particle filter
warning light has not illuminated).
STATUS 4Request by number of regeneration failures or weight of soot
This status corresponds to the appearance of DF312 Speed request.
This corresponds to the maximum number of failed regenerations or to the maximum
weight of soot in the particle filter, with illumination of the particle filter warning light.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-263
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V9 MR-372-J84-13B450$151.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR002ALTERNATOR CHARGE
PARAMETER
DEFINITIONThis parameter indicates the charge value of the alternator in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
The alternator charge value varies according to the battery voltage.
EDC16C36_V44_PR002/EDC16C36_V4C_PR002/EDC16C36_V48_PR002/EDC16C36_V50_PR002/EDC16C36_V54_PR002/
EDC16C36_V58_PR002
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58