RENAULT SCENIC 2011 J95 / 3.G Engine And Peripherals Workshop Manual

13B-111V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued 2):
*When the air conditioning is requested with the engine idling and the vehicle speed = 0 mph (0 km/h),
ET022 will always be ACTIVE and ET021 INACTIVE (unless refrigerant pressure > 15 bar, vehicle speed
= 0 mph (0 km/h) and high coolant temperature). The fan assemblies are disabled under certain coolant
temperature conditions when driving.
When the UPC stops receiving multiplex transmissions from the injection, the fan assemblies are
constantly activated.
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check or
actionDisplay and notes Fault finding
Power consumed
by the air
conditioning
compressorPR125: Power
consumed by the
air conditioning
compressor.
0 WATTIndicates the power consumed by the
compressor.NONE
Fan assembly
speed request*ET022: Low speed
fan assembly
request.
INACTIVE.The injection requests the UPC to start the fans.
- INACTIVE: The request was not made by the
injection because ET088 = INACTIVE and ET004
=NO.
- ACTIVE: The request was made by the injection.
ET088 = ACTIVE and ET004 = YES.
(Correct refrigerant pressure and vehicle speed
= 0 mph (0 km/h) or high coolant temperature).
NONE
ET021: High
speed fan
assembly request.
INACTIVE.The injection requests the UPC to start the fans.
- INACTIVE: The request was not made by the
injection because ET088 = INACTIVE and ET004
=NO.
- ACTIVE: The request was made by the injection.
ET088 = ACTIVE and ET004 = YES.
(Refrigerant pressure > 15 bar and vehicle speed
= 0 mph or high engine coolant temperature).

13B-112V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
HEATING SUB-FUNCTION:
*RCH = Passenger Compartment Heating Resistor
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or
Status Check or
actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant temperature in °C.
Default value: 80°C
RCH* number setET111: RCH*
number set.
YES - NOThe RCHs* are actuated by the UCH. They are high
current consumers. Consequently, their use is
conditional on the available power all the time
(alternator power). The injection checks the
balance of available mechanical power according
to the engine operating conditions (torque, power,
etc.) to authorise, limit, or stop their use.
(This information is sent via the CAN to the UCH).
Note: When the RCHs* are actuated, the injection
system must respond to a fast idle speed request
from the UCH.NONE
RCH cut-offET112: RCH*
cut-off
YES - NO

13B-113V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
FUEL CIRCUIT SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Fuel temperaturePR063: Fuel temperature.
Cold = PR064
Warm: 50°CGives the fuel temperature in °C.
Default value: 30°C.In the event of a fault,
apply the fault finding
procedure for fault
DF098 "Fuel
temperature sensor
circuit".
Fuel flowPR017: Fuel flow.
10 < Cold < 2 mg/st
4 < Warm < 6 mg/stShows the fuel injected in mg/st for
each injector.NONE
Rail pressurePR038: Rail pressure.
Cold: 260 bar.
Warm: 230 barIndicates the pressure, in bar, of
the diesel fuel in the injector rail.
This pressure is supplied by the
sensor on the rail.
Default value: 2000 barIn the event of a fault
apply the fault finding
procedure for fault
DF007 "Rail pressure
sensor circuit".
Rail pressure set
pointPR008: Rail pressure
setpoint.
375 bar (Engine starting
pressure setpoint).
Cold: 260 bar.
Warm: 230 barGives the theoretical pressure
value for optimum engine
operation.NONE
Rail pressure
sensor voltage PR080: Rail pressure
sensor voltage.Shows the voltage supplied by
the computer to the rail pressure
sensor.
0.5 V (0 bar) < PR080 < 4.5 V
(1600 bar)NONE

13B-114V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
FUEL CIRCUIT SUB-FUNCTION (continued):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Engine speedPR055: Engine speed.
Cold: 900 rpm.
Warm: 805 rpm.Indicates the engine's speed of
rotation in rpm.In the event of a fault,
apply the fault finding
procedure for
DF005 "Engine speed
sensor circuit".
New pump
chamber fillingET637: New pump
chamber fillingCOMPLETEDIf NOT DONE, see
Replacement of
components.

13B-115V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PRE-HEATING/IGNITION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant temperature
in °C.
Default value: 80°CIn the event of a fault,
consult the
interpretation of
parameter PR064
Coolant temperature.
External air
temperaturePR061: External air
temperature.Gives the external air temperature
in °C. This parameter is controlled
by the UCH and transmitted to the
injection via the multiplex network.
Default value: 20°CIn the event of a fault,
apply the fault finding
procedure for this fault
described in the UCH
document.
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air temperature
in °C. This signal is provided by the
air temperature/pressure sensor.
Default value: 30°C.In the event of a fault,
refer to the
interpretation of
parameter PR059 Inlet
air temperature.
Battery voltage PR074: Battery voltage.12 V < PR074 < 14 VIf there is a fault, apply
the fault finding
procedure for the
"Charge circuit".

13B-116V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
AIR CIRC. SUB-FUNCTION (TURBO/INLET):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Inlet air
temperature
(invalid for
K9K 728)PR059:
Inlet air temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air temperature
in °C. This signal is provided by the
air temperature/pressure sensor.
Default value: 30°C.In the event of a fault,
refer to the
interpretation of
parameter PR059 Inlet
air temperature.
Air circuit
pressure.PR035: Atmospheric
pressure.Indicates the atmospheric pressure
in mbar. The sensor is built into
the computer.If not consistent, check
that PR035 = PR032 =
local atmospheric
pressure, with the
engine stopped and the
ignition on. PR032: Inlet pressure.Indicates the pressure in the inlet
circuit in mbar.
Air flow.PR132: Air flow.
350 < Cold < 400 mg/st
300 < Cold < 350 mg/stAir flow estimated by the injection
computer.NONE
Inlet temperature
sensor voltagePR081: Inlet temperature
sensor voltage.Indicates the voltage, in volts,
delivered by the computer to
supply the inlet temperature
sensor.NONE
Engine speedPR055: Engine speed.
Cold: 900 rpm.
Warm: 805 rpmIndicates the engine's speed of
rotation in rpm.In the event of a fault,
apply the fault finding
procedure for
DF005 "Engine speed
sensor circuit".

13B-117V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
ENGINE COOLING SUB FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault,
consult the interpretation
of parameter PR064
Coolant temperature.

13B-118V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
DRIVER PARAMETERS SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Accelerator pedal
positionPR030: Accelerator
pedal position.
0%.Shows the pedal position
between NO LOAD and FULL
LOAD as a percentage.
0% < PR030 < 100%In the event of a fault,
apply the fault finding
procedures for Pedal
sensor circuit gang 1 and
gang 2 (DF008 and DF009)
and DF113 Sensor supply
voltage.
Pedal
potentiometer
gang voltagesPR086: Pedal
potentiometer gang 1
voltage.
16%Shows the percentage of feed
voltage on gangs 1 and 2 of the
pedal potentiometer.In the event of a fault,
apply the fault finding
procedures for Pedal
sensor circuit gang 1 and
gang 2 (DF008 and DF009)
and DF113 Sensor supply
voltage. PR088: Pedal
potentiometer gang 2
voltage.
7%10% < PR086 < 20%
5% < PR088 < 15%

13B-119V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
EMISSION CONTROL/OBD SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
EGR valve
controlET008: EGR valve control.
INACTIVEIndicates the EGR valve control
status.
- INACTIVE: The valve is not
controlled by the computer.
- ACTIVE: The valve is controlled by
the computer.NONE
Atmospheric
pressurePR035: Atmospheric
pressure.Indicates the atmospheric
pressure in mbar. The sensor is
built into the computer.If not consistent, check
that PR035 = PR032 =
local atmospheric
pressure, with the
engine stopped
and the ignition on.
Air flowPR132: Air flow.
350 < Cold < 400 mg/st
300 < Cold < 350 mg/stAir flow estimated by the injection
computer.NONE
Fuel flowPR017: Fuel flow.
10 < Cold < 12 mg/st
4 < Warm < 6 mg/st.Gives the fuel flow at the high
pressure pump outlet in mg/st.NONE
EGR valve
opening setpointPR005: EGR valve opening
setpoint.
Warm: 20%Gives a theoretical EGR valve
opening value for optimum engine
operation.
PR005 = PR051NONE
EGR valve
position
feedbackPR051: EGR valve position
feedback.
Warm approximately 20 %Shows the true EGR valve
position.
Default value: 30%NONE

13B-120V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
SUB-FUNCTION: ANTIPOLLUTION/OBD (cont.):
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
EGR valve
position sensor
voltagePR077: EGR valve position
sensor voltage.Indicates the EGR valve voltage
according to its position.
- INACTIVE: The valve is not
controlled by the computer.
- ACTIVE: The valve is controlled
by the computer.
0.5 V < PR077 < 4.8 VNONE
Accelerator pedal
positionPR030: Accelerator pedal
position.
0%.Shows the pedal position
between NO LOAD and FULL
LOAD as a percentage.
0< PR030 < 100%In the event of a fault,
apply the fault finding
procedures for Pedal
sensor circuit gang 1 and
gang 2 (DF008 and DF009)
and DF113 Sensor supply
voltage.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90 °CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault,
consult the interpretation
of parameter PR064
Coolant temperature.