RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Workshop Manual

13B-121
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF060
PRESENT
OR
STOREDMISFIRING ON CYLINDER 2
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault reappears after:
– engine speed PR055 Engine speed between idle speed and 1050 rpm,
– a coolant temperature PR064 Coolant temperature ≥ 20°C.
Priorities when dealing with a number of faults:
– DF027 Cylinder 2 injector control circuit
– DF052 Injector control circuit.
Special notes:
After an injector has been replaced, run commands SC002 Enter injector codes and
SC036 Reinitialise programming and follow the procedure.
IMPORTANT:
Cylinder no. 1 is located at the timing end.
Do not disconnect the injectors when the engine is running.
When removing and refitting an injector, respect the cleanliness guidelines and safety
advice (see MR364 (Mégane II ph2), MR370 (Scénic II ph2), MR 395 (Laguna II
ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2), Mechanical, 13B, Diesel injection,
Diesel injectors: Removal - Refitting).
EDC16CP33_V18_DF060 / EDC16CP33_V1C_DF060 / EDC16CP33_V54_DF060 / EDC16CP33_V20_DF060 / EDC16CP33_V58_DF060 /
EDC16CP33_V5C_DF060 / EDC16CP33_V24_DF060 / EDC16CP33_V04_DF060 / EDC16CP33_V08_DF060 / EDC16CP33_V44_DF060 /
EDC16CP33_V4C_DF060 / EDC16CP33_V34_DF060 / EDC16CP33_V38_DF060 / EDC16CP33_V74_DF060 / EDC16CP33_V28_DF060 /
EDC16CP33_V62_DF060 / EDC16CP33_V26_DF060 / EDC16CP33_V60_DF060

13B-122
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF060
CONTINUED
Perform TEST 2 Resolving misfires.
If the fault is still present, contact the Techline.

13B-123
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF061
PRESENT
OR
STOREDMISFIRING ON CYLINDER 3
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault reappears after:
– engine speed PR055 Engine speed between idle speed and 1050 rpm,
– a coolant temperature PR064 Coolant temperature ≥ 20°C.
Priorities when dealing with a number of faults:
– DF028 Cylinder 3 injector control circuit
– DF052 Injector control circuit.
Special notes:
After an injector has been replaced, run commands SC002 Enter injector codes and
SC036 Reinitialise programming and follow the procedure.
IMPORTANT:
Cylinder no. 1 is located at the timing end.
Do not disconnect the injectors when the engine is running.
When removing and refitting an injector, respect the cleanliness guidelines and safety
advice (see MR364 (Mégane II ph2), MR370 (Scénic II ph2), MR 395 (Laguna II
ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2), Mechanical, 13B Diesel injection,
Diesel injectors: Removal - Refitting).
EDC16CP33_V18_DF061 / EDC16CP33_V1C_DF061 / EDC16CP33_V54_DF061 / EDC16CP33_V20_DF061 / EDC16CP33_V58_DF061 /
EDC16CP33_V5C_DF061 / EDC16CP33_V24_DF061 / EDC16CP33_V04_DF061 / EDC16CP33_V08_DF061 / EDC16CP33_V44_DF061 /
EDC16CP33_V4C_DF061 / EDC16CP33_V34_DF061 / EDC16CP33_V38_DF061 / EDC16CP33_V74_DF061 / EDC16CP33_V28_DF061 /
EDC16CP33_V62_DF061 / EDC16CP33_V26_DF061 / EDC16CP33_V60_DF061

13B-124
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF061
CONTINUED
Perform TEST 2 Resolving misfires.
If the fault is still present, contact the Techline.

13B-125
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF062
PRESENT
OR
STOREDMISFIRING ON CYLINDER 4
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault reappears after:
– engine speed PR055 Engine speed between idle speed and 1050 rpm,
– a coolant temperature PR064 Coolant temperature ≥ 20°C.
Priorities when dealing with a number of faults:
– DF029 Cylinder 4 injector control circuit
– DF052 Injector control circuit.
Special notes:
After an injector has been replaced, run commands SC002 Enter injector codes and
SC036 Reinitialise programming and follow the procedure.
IMPORTANT:
Cylinder no. 1 is located at the timing end.
Do not disconnect the injectors when the engine is running.
When removing and refitting an injector, respect the cleanliness guidelines and safety
advice (see MR364 (Mégane II ph2), MR370 (Scénic II ph2), MR 395 (Laguna II
ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2), Mechanical, 13B Diesel injection,
Diesel injectors: Removal - Refitting).
EDC16CP33_V18_DF062 / EDC16CP33_V1C_DF062 / EDC16CP33_V54_DF062 / EDC16CP33_V20_DF062 / EDC16CP33_V58_DF062 /
EDC16CP33_V5C_DF062 / EDC16CP33_V24_DF062 / EDC16CP33_V04_DF062 / EDC16CP33_V08_DF062 / EDC16CP33_V44_DF062 /
EDC16CP33_V4C_DF062 / EDC16CP33_V34_DF062 / EDC16CP33_V38_DF062 / EDC16CP33_V74_DF062 / EDC16CP33_V28_DF062 /
EDC16CP33_V62_DF062 / EDC16CP33_V26_DF062 / EDC16CP33_V60_DF062

13B-126
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF062
CONTINUED
Perform TEST 2 Resolving misfires.
If the fault is still present, contact the Techline.

13B-127
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF065
PRESENT
OR
STOREDCOMBUSTION MISFIRES
1.DEF: Combustion misfires detected on several cylinders.
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault reappears after:
– engine speed PR055 Engine speed between idle speed and 1050 rpm,
– a coolant temperature PR064 Coolant temperature ≥ 20°C.
Priorities when dealing with a number of faults:
– DF052 Injector control circuit
– DF026 Cylinder 1 injector control circuit
– DF027 Cylinder 2 injector control circuit
– DF028 Cylinder 3 injector control circuit
– DF029 Cylinder 4 injector control circuit
IMPORTANT:
When removing and refitting an injector, respect the cleanliness guidelines and safety
advice (see MR364 (Mégane II ph2), MR370 (Scénic II ph2), MR 395 (Laguna II
ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2), Mechanical, 13B Diesel injection,
Diesel injectors: Removal - Refitting).
Perform TEST 2 Resolving misfires.
If the fault is still present, contact the Techline.
EDC16CP33_V18_DF065 / EDC16CP33_V1C_DF065 / EDC16CP33_V54_DF065 / EDC16CP33_V20_DF065 / EDC16CP33_V58_DF065 /
EDC16CP33_V5C_DF065 / EDC16CP33_V24_DF065 / EDC16CP33_V04_DF065 / EDC16CP33_V08_DF065 / EDC16CP33_V44_DF065 /
EDC16CP33_V4C_DF065 / EDC16CP33_V34_DF065 / EDC16CP33_V38_DF065 / EDC16CP33_V74_DF065 / EDC16CP33_V28_DF065 /
EDC16CP33_V62_DF065 / EDC16CP33_V26_DF065 / EDC16CP33_V60_DF065

13B-128
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
DF066
PRESENT
OR
STOREDINJECTOR(S) CODE(S)
1.DEF: No code stored
2.DEF: Configuration/Initialisation
NOTESSpecial notes:
If the fault is present:
– the injection flow will be limited,
– engine torque limited, resulting in a maximum engine speed of 1500 rpm,
–the level 1 warning light is illuminated.
1.DEF
NOTESSpecial notes:
This fault appears when an incorrect injector code is entered
from command SC002 Enter injector codes. The IMA*
codes must be read from left to right.
Check the injector codes and reprogram the correct codes using command SC002 Enter injector codes, see
Interpretation of commands.
(Consult the procedures defined in the Interpretation of commands section).
– After the codes have been written:
– Switch off the ignition.
– Wait for the diagnostic tool message (maximum wait 8 minutes): Loss of dialogue with the computer:
EDC16 CP33, check the tool connection and the computer supply before switching the ignition back on.
– Establish dialogue and clear the fault memory.
– End of the procedure.
EDC16CP33_V18_DF066 / EDC16CP33_V1C_DF066 / EDC16CP33_V54_DF066 / EDC16CP33_V20_DF066 / EDC16CP33_V58_DF066 /
EDC16CP33_V5C_DF066 / EDC16CP33_V24_DF066 / EDC16CP33_V04_DF066 / EDC16CP33_V08_DF066 / EDC16CP33_V44_DF066 /
EDC16CP33_V4C_DF066 / EDC16CP33_V34_DF066 / EDC16CP33_V38_DF066 / EDC16CP33_V74_DF066 / EDC16CP33_V28_DF066 /
EDC16CP33_V62_DF066 / EDC16CP33_V26_DF066 / EDC16CP33_V60_DF066

13B-129
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
IMA*: Individual injector correction
IMA*: Individual injector correction
DF066
CONTINUED 1
WARNING:
If fault DF066 is still present after the injector codes have been entered, check that power latch occurs each time
the ignition is switched off:
– Switch off the ignition.
– Wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the computer: EDC16
CP33, check the tool connection and the computer supply voltage and switch on the ignition again.
– Establish dialogue.
If the fault has become stored, clear the fault memory and end the operation.
If the fault is still present, contact the Techline.
2.DEF
NOTESConditions for applying the fault finding procedure to a
stored fault:
The fault is declared present after:
– the injection computer has been replaced,
– reprogramming.
This fault is present on all blank computers (new or after reprogramming).
– Program the injector codes using:
– either command SC001 Write saved data,
– or command SC002 Enter injector codes or Interpretation of commands.
The IMA* codes must be read from left to right.
(Consult the procedures defined in the Interpretation of commands section).

13B-130
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition until the end of the power-latch phase, and carry out a road test
followed by a check with the diagnostic tool.
V12 MR-372-J84-13B300$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
IMA*: Individual injector correction
DF066
CONTINUED 2
– After the codes have been written:
– Switch off the ignition.
– Wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the computer: EDC16
CP33, check the tool connection and the computer supply voltage and switch on the ignition again.
– Establish dialogue and clear the fault memory.
End of the procedure.
WARNING:
If fault DF066 is still present after the injector codes have been entered, check that power latch occurs each time
the ignition is switched off:
– Switch off the ignition.
– Wait for the diagnostic tool message (maximum wait 8 min): Loss of dialogue with the computer: EDC16
CP33, check the tool connection and the computer supply voltage and switch on the ignition again.
– Establish dialogue.
If the fault is still present, contact the Techline.