section 2c SSANGYONG KORANDO 1997 Service Repair Manual

SSANGYONG MY2002
9G-8 INTERIOR TRIM
KAA9G170
8. Remove the kick panel. Refer to “Kick Panel” in
this section.
9. Remove the lower quarter trim panel. Refer to
“Lower Quarter Trim Panel” in this section.
10. Remove the front floor carpet.
11. Installation should follow the removal procedure
in the reverse order.

SECTION 9H
SEATS
TABLE OF CONTENTS
Components Locator............................................9H-2
Seats ...................................................................9H-2
Repair Instructions................................................9H-3
On-Vehicle Service Unit Repair................................9H-3
Front Seat............................................................9H-3
Front Seat Cushion..............................................9H-3
Front Seatback....................................................9H-4
Front Seat Guide Rail ...........................................9H-4
Front Seat Recliner Lever.....................................9H-5
Front Seat Trim....................................................9H-5
Head Restraint.....................................................9H-5Walk In Device....................................................9H-6
Front Seat Armrest...............................................9H-6
Rear Seat Armrest ...............................................9H-6
Rear Seat............................................................9H-7
50/50 Split Rear Seat Cushion Hinge....................9H-7
50/50 Split Rear Seat Cushion Lock Striker...........9H-8
Child Seat Anchorage ..........................................9H-8
Specifications.......................................................9H-9
Fastener Tightening Specifications.......................9H-9
Schematic and Routing Diagram......................9H-10
Seat Heater.......................................................9H-10

SEATS 9H-3
SSANGYONG MY2002
REPAIR INSTRUCTIONS
KAA9H020
ON-VEHICLE SERVICE
UNIT REPAIR
FRONT SEAT
Removal and Installation Procedure
1. Remove the electrical connector from front seat.
KAA9H030
2. Remove the bolts with the front seat.
Installation Notice
•Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Installation should follow the removal procedure
in the reverse order.
Tightening Torque19.6 - 31.4 Nm
(14.5 - 23.2 lb-ft)
KAA9H060
FRONT SEAT CUSHION
Removal and Installation Procedure
1. Remove the front seat from the vehicle. Refer to
“front seat” in this section.
2. Remove the front seatback. Refer to “Front Seat
back” in this section.
3. Remove the seat cushion bolts.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
4. Installation should follow the removal procedure
in the reverse order.
Tightening Torque16.7 - 25.5 Nm
(12 - 18 lb-ft)

SSANGYONG MY2002
9H-4 SEATS
KAA9H070
FRONT SEAT GUIDE RAIL
Removal and Installation Procedure
1. Remove the front seat from the vehicle. Refer to
in this section.
2. Remove the front seat trim. Refer to “front seat
trim” in this section.
3. Remove the bolts and the guide rail.
Installation Notice
KAA9H050
6. Remove the bolts and the seatback.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
7. Installation should follow the removal procedure
in the reverse order.
Tightening Torque34.3 - 55.9 Nm
(25 - 41 lb-ft)
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
4. Installation should follow the removal procedure
in the reverse order.
Tightening Torque17.6 - 25.5 Nm
(12 - 18 lb-ft)
KAA9H040
FRONT SEATBACK
Removal and Installation Procedure
1. Remove the front seat from the vehicle. Refer to
“front seat” in this section.
2. Remove the head restraint. Refer to “head
restraint” in this section.
3. Remove the seat recliner lever. Refer to “seat
recliner lever” in this section.
4. Remove the seat trim. Refer to “seat trim” in this
section.
5. Remove the seatback cover.

SEATS 9H-5
SSANGYONG MY2002
KAA9H100
KAA9H080
KAA9H090
FRONT SEAT TRIM
Removal and Installation Procedure
1. Remove the recliner lever by rubber hammer. Refer
to “seat recliner lever” in this section.
2. Remove the screws and the seat trim.
3. Installation should follow the removal procedure
in the reverse order.
FRONT SEAT RECLINER LEVER
Removal and Installation Procedure
1. Remove the seat recliner lever by rubber hammer.
2. Installation should follow the removal procedure
in the reverse order.
HEAD RESTRAINT
Removal and Installation Procedure
1. Press in the head restraint adjust button and
remove the head restraint from the seatback.
KAA9H110
2. Insert two flat head screwdrivers down the front
and back side of the guide sleeves.
3. With the screwdrivers, press in the retaining
latches and remove the guide sleeves.
4. Installation should follow the removal procedure
in the reverse order.

SSANGYONG MY2002
9H-6 SEATS
KAA9H120
KAA9H130
WALK IN DEVICE
Removal and Installation Procedure
1. Remove the front seat. Refer to “front seat” in this
section.
2. Remove the seat recliner. Refer to “seat recliner”
in this section.
3. Remove the seat trim. Refer to “seat trim” in this
section.
4. Remove the walk in device assembly.
5. Installation should follow the removal procedure
in the reverse order.
FRONT SEAT ARMREST
Removal and Installation Procedure
1. Remove the arm rest cover.
2. Remove the arm rest mounting bolt.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Remove the arm rest.
4. Installation should follow the removal procedure
in the reverse order.
Tightening Torque17.6 - 25.5 Nm
(12 - 18 lb-ft)
KAA9H180
REAR SEAT ARMREST
Removal and Installation Procedure
1. Push the button in the arm rest.
2. Turn and remove from the side quarter trim panel.
3. Installation should follow the removal procedure
in the reverse order.

SECTION 9I
WATERLEAKS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless
otherwise noted.
TABLE OF CONTENTS
Specifications........................................................9I-2
Recommended Materials for Waterleak Repairs....9I-2
Watertest Stand Specifications.............................9I-2
Diagnosis...............................................................9I-3Waterleak Diagnosis.............................................9I-3
Maintenance and Repair......................................9I-6
On-Vehicle Service..................................................9I-6
Waterleak Repair..................................................9I-6

SSANGYONG MY2002
9I-4 WATERLEAKS
3. Perform the watertest stand leak test. Refer to
“Watertest Stand Specifications” in this section.
4. If the local water pressure does not allow the
required water pressure of 155 kPa (22.5 psi),
move both stands closer to the vehicle so that
the water sprayoverlaps.
Localized Testing (Spot Test)
1. Do localized testing with a water hose or an air
hose.
2. Begin testing by spraying the air or the water at
the base of the suspected leak area. Continue
spraying the air or the water upward until the leak
is found.
KAA9I030
KAA9I020
2. Set up the watertest stand leak test.

SECTION 9J
WINDNOISE
TABLE OF CONTENTS
Diagnosis..............................................................9J-2
Windnoise Diagnosis ...........................................9J-2Maintenance and Repair.....................................9J-3
On-Vehicle Service.................................................9J-3
Windnoise Repair................................................9J-3

WINDNOISE 9J-3
SSANGYONG MY2002
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
WINDNOISE REPAIR
Windnoise leak repairs are very similar to waterleak
repairs. Refer to Section 9I, Waterleaks. The actual
procedure depends on the type of seal being repaired.
Leaks around the door opening weatherstrips do not
al-ways indicate a faulty weatherstrip. A door or window
adjustment may resolve the condition. Refer to Section
9P, Doors or Section 9L, Glass and Mirrors.