head SSANGYONG KORANDO 1997 Service Manual PDF

1B2 -- 106 M161 ENGINE MECHANICAL
D AEW OO M Y_2000
CYLINDER HEAD MATING SURFACE
Preceding Work: Removal of valves
ServiceDataStandard
Overall Height of Cylinder Head135.9 -- 136.0 mm
Minimum Height After Machining135.5 mm
FlatnessAxial Direction0.08 mm
Transverse Direction0.0 mm
Distance ‘T’
(BtChftBi
Standard SizeIntake24.21 -- 24.75 mm
(Between Camshaft Bearing
andValveStem)Exhaust22.21 -- 22.75 mmandValveStem)
Repair SizeIntake23.96 -- 24.51 mmp
Exhaust21.96 -- 22.51 mm
Notice:Do not exceed 0.4mm for the milling of the mating surface of crankcase and cylinder head.

M161 ENGINE MECHANICAL 1B2 -- 107
D AEW OO M Y_2000
Measurement of Mating Surfac
1. Measure the height (H) of the cylinder head(refer to
Service data standard).
2. Check the mating surface of the cylinder head.
3. Mill the sharp edge of the combustion chamber.
4. Re-- measure the height (H) of the cylinder head.
5. Seal the intake and exhaust valves.
6. Measure the dimension (T) between the camshaft
bearing and the valve system(refer to Service data
standard).
7. Mill the cylinder head valve seat(refer to Service data
standard).
Universal Tool
Surface Grinding Machine
Sceledum, Type RTY
Roaro
Schio/Italy

1F2 -- 20 M161 ENGINE CONTROLS
D AEW OO M Y_2000
IGNITION COIL
YAA1F920
The Electronic Ignition (EI) system ignition coil is located on the cylinder head cover. The double ended coils receive
the signal for the Engine Control Module (ECM) which controls the spark advance.
Each EI system ignition coil provides the high voltage to two spark plugs simultaneously;
T1/1: cylinder 1 and 4
T1/2: cylinder 2 and 3
The EI system ignition coil is not serviceable and must be replaced as an assembly.

1F2 -- 100 M161 ENGINE CONTROLS
D AEW OO M Y_2000
YAA1F770
Notice:Before removal, the fuel rail assembly may be
cleaned with a spray-type cleaner, following package in-
structions. Do not immerse the fuel rails in liquid clean-
ing solvent. Use care in removing the fuel rail assembly
to prevent damage to the electrical connectors and in-
jector spray tips. Prevent dirt and other contaminants
from entering open lines and passages. Fittings should
be capped and holes plugged during service.
Important:If an injector becomes separated from the
rail and remains in the cylinder head, replace the injector
O-ring seals and the retaining clip.
12. Remove the injectors and the fuel rail carefully.
13. Remove the fuel injector retainer clips.
14. Remove the fuel injectors by pulling them down and
out.
15. Discard the fuel injector O-rings.
16. Lubricate the new fuel injector O-rings with engine
oil. Install the new O-rings on the fuel injectors.
17. Perform a leak check of the fuel rail and fuel injec-
tors.
18. Installation should follow the removal procedure in
the reverse order.
YAA1F780
ENGINE COOLANT TEMPERATURE
SENSOR
Removal and Installation Procedure
1. Relieve the coolant system pressure.
2. Disconnect the negative battery cable.
3. Disconnect the engine coolant temperature sensor
connector.
Notice:Take care when handling the engine coolant
temperature sensor. Damage to the sensor will affect
the proper operation of the fuel injection system.
4. Remove the engine coolant temperature sensor
from the pump hosing.
Installation Notice
Tightening Torque
30 NSm (22 Ib-ft)
5. Installation should follow the removal procedure in
the reverse order.

GENERAL ENGINE INFORMATION 1A3 -- 13
D AEW OO M Y_2000
CYLINDER PRESSURE LEAKAGE TEST
1 Connector
2 Connection Piece
3 Connection Hose
Permissible Pressure Leakage (Engine at Normal Operating Temperature of 80_C)
At Whole EngineMax. 25 %
At Valve and Cylinder Head GasketMax. 10 %
At Piston and Piston RingMax. 20 %
Commercial Tools
Cylinder Pressure Leakage testerBOSCH, EFAW 210 A or SUN CLT 228
Connection PieceBOSCH order no. 1 687 010 016

D AEW OO M Y_2000
SECTION 1B3
OM600 ENGINE MECHANICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless
otherwise noted.
TABLE OF CONTENTS
Specifications 1B3 -- 2............................
Fastener Tightening Specifications 1B3 -- 2..........
Special Tools 1B3 -- 4.............................
Special Tools Table 1B3-- 4.......................
Maintenance and Repair 1B3 -- 12..................
On-- Vehicle Service 1B3-- 12........................
Engine Assembly 1B3-- 12........................
Poly V-- Belt 1B3 -- 21.............................
Tensioning Device 1B3-- 23.......................
Poly V-- Belt Alignment & Inspection 1B3-- 26........
Prechamber 1B3-- 29............................
Milling of Prechamber Sealing Surface 1B3 -- 32.....
TDC (TDC Sensor Bracket) Setting 1B3 -- 35........
Cylinder Head 1B3-- 37...........................
Timing Case Cover 1B3 -- 63......................
Crankshaft End Cover 1B3-- 71...................
Vibration Damper and Hub 1B3-- 74...............
Crankshaft Front Radial Seal 1B3-- 80.............
Crankshaft Ball Bearing 1B3-- 82..................
Crankshaft 1B3-- 83.............................
Flywheel 1B3 -- 93...............................
Machining of Flywheel 1B3-- 97...................
Flywheel Ring Gear 1B3 -- 98......................
Hydraulic Valve Clearance Compensation
Element Check 1B3-- 101.........................
Valve Tappets 1B3-- 103..........................
Valve Spring Check 1B3-- 105.....................Valve Springs (Cylinder Head Removed) 1B3-- 106..
Valve Springs (Cylinder Head Installed) 1B3-- 109...
Valve Stem Seals 1B3-- 112......................
Check and Replacement of Valve Guides 1B3-- 116..
Valve Seat Rings 1B3-- 122.......................
Check and Machining of Valves 1B3-- 127..........
Machining of Valve Seat 1B3-- 132.................
Camshaft Timing Test 1B3-- 137...................
Camshaft 1B3-- 139.............................
Chain Tensioner 1B3-- 145........................
Timing Chain 1B3-- 147...........................
Tensioning Rail 1B3-- 151.........................
Cylinder Head Guide Rail 1B3-- 152................
Timing Case Cover Guide Rail 1B3-- 156...........
Crankshaft Sprocket 1B3-- 158....................
Piston 1B3-- 163.................................
Oil Filter 1B3-- 169...............................
Oil Pan 1B3-- 171................................
Oil Spray Nozzle 1B3-- 174.......................
Oil Pump 1B3-- 175..............................
Unit Repair 1B3 -- 177............................
Cylinder Head Pressure Leakage Test 1B3-- 177....
Facing Cylinder Head Mating Surface 1B3 -- 178.....
Replacement of Crankcase Core Plug 1B3-- 180.....
Facing Crankcase Contacting Surface 1B3 -- 182....
Oil Gallery Steel Ball 1B3-- 183....................
Cylinder Bore Measurement 1B3-- 187.............

OM600 ENGINE MECHANICAL 1B3 -- 3
D AEW OO M Y_2000
Cylinder Head
ApplicationNSmLb-- FtLb-- In
Prechamber Threaded Ring13096--
Cylinder Head Cover Bolt10--89
Fuel Injsction Pipe Nut1813--
Socket Bolt2518--
Fuel Filter Pipe Bolt2518--
Idle Pulley Bolt2317--
Damper Bolt2115--
Camshaft Bearing Cap Bolt2518--
Camshaft Sprocket Bolt25 / 90_18 / 90_--
Exhaust Pipe Bolt& Nut2518--
Chain Tensioner8059--
Injection Nozzle4030--
Intake Manifold Not2518--
Injection Nozzle Pipe Not1813--
Oil Dipstick Tube Bolt10--89
Screw Plug M18 x 155037--
Cam Support & Shaft
ApplicationNSmLb-- FtLb-- In
Stud Bolt12--106
Exhaust Manifold Not2518--
CamShaft Bearing Cap Bolt2518--
12-- Sided Bolt (M11)25 / 90_18 / 90_--
Timing Cover
ApplicationNSmLb-- FtLb-- In
Oil Pan Bolt -- Socket Bolt10--89
Oil Pan Bolt--M610--89
Oil Pan Bolt--M232317--
Belt Pulley Bolt3224--
Guide Pulley Bolt4--35
Guide Pulley Bracket Nut2317--
Chain Tensioner8059--
Tesioning Lever Bolt2317--

OM600 ENGINE MECHANICAL 1B3 -- 5
D AEW OO M Y_2000
SPECIAL TOOLS TABLE (Cont’d)
116 589 03 07 00
T Type Socket Wrench
601 589 00 10 00
Cylinder Head Bolt 102
102 589 12 15 00
(φ17) Drift
617 589 10 21 00
RI Sensor
115 589 34 63 00
602 589 00 25 00
102 589 00 15 00
(φ34) Drift
601 589 05 14 00
Assembly Cage

OM600 ENGINE MECHANICAL 1B3 -- 29
D AEW OO M Y_2000
PRECHAMBER
Preceding Work : Removal of glow plug
Removal of fuel injection nozzle
1 Threaded Ring 130 N∙m (96 lb-ft) ...........
2 Prechamber3 Cylinder Head

1B3 -- 30 OM600 ENGINE MECHANICAL
D AEW OO M Y_2000
Tools Required
603 589 00 09 00 Serration Wrench
667589036300 SlidingHammer
Removal & Installation Procedure
1. Using the serration wrench (4), remove the threaded
ring (1).
Serration Wrench 603 589 00 09 00
2. Install the sliding hammer into the prechamber.
Sliding Hammer 667 589 03 63 00
3. Remove the perchamber (2).
Notice
After removing the prechamber, cover over the
bores with clean rag.
4. Inspect the prechamber.
Notice
If the prechamber seats in the cylinder head are
leaking or if the prechambers are replaced, the seal-
ing surfaces in the cylinder head must be rema-
chined.