automatic SSANGYONG KORANDO 2012 Owner's Manual

03-16
Washer coupled wiper in rain sensing mode ▶
When the washer switch signal is received during intermittent operation coupled with rain sensor
with IGN ON and intermittent/automatic washer switch operation, the wipers operate in washer
coupled mode regardless of the communication with the rain sensor. However, if the washer switch
signal is received the washer relay is activated and wiper relay remains activated, when the data
coupled with rain sensor indicates continuous wiper operation.
Even though the wiping system is in washer coupled wiper mode, the operating data are sent to rain
sensor. 1.
2.
Sensitivity adjustment (instant wiping) ▶
When the wiping speed control switch is turned to "FAST" with IGN2 ON, intermittent/automatic wiper
switch in "ON" position and wiper motor stop (parking position), the wiper motor operates one cycle at
low speed.
(only when the rain sensor detects raindrops)
If the wiping speed control switch is changed more than 2 stages within 2 seconds, the wiper motor
operates only one cycle. 1.
*

03-18
Processing method for rain sensor malfunction ▶
If the BCM is received the signal for sensor malfunction from the rain sensor unit when turning the
wiping speed control switch to 2 from 3 stage with IGN ON and intermittent/automatic wiper switch in
"ON" position, the wiper motor operates one cycle at low speed. 1.
If the BCM is received the signal for communication error from the rain sensor unit when turning the
wiping speed control switch to 3 from 4 stage with IGN ON and intermittent/automatic wiper switch in
"ON" position, the wiper motor operates one cycle at low speed. 2.

03-20
Wiper low/high control ▶
The wiper low relay is activated when the wiper low switch is operated and the wiper high relay
activated when the wiper high switch is operated.
The wiper motor returns to parking position and stops, even when turning off the ignition switch during
wiper operation.
The wiper relay should remain activated during wiper operation in low/high mode even though the
system does not receive P-POS signal. (During intermittent/automatic wiper operation, the wiper relay
should be deactivated after 5 seconds if there is no P-POS signal for 3 seconds in order to inform the
driver of faulty signal)
While the wiper operates at low/high speed, the front/rear washer switch can be operated but the auto
washer switch cannot.
The wiper motor returns to parking position and stops when turning off the ignition switch during wiper
operation in high mode. 1.
2.
3.
4.
5.

03-258710-01
Tail lamp auto OFF ▶
When opening and closing the driver door after turning off the ignition with the tail lamp ON, the tail
lamps go off automatically.
The tail lamps come on again when inserting the ignition key (without SKM) and turning on the
ignition (with SKM) after tail lamp auto OFF.
The tail lamp should not go off when turning on the tail lamp switch with the ignition key removed
(without SKM) and with power off or ACC ON (with SKM). 1.
2.
3.
Tail lamp ON warning (with SKM) ▶
The tail lamp ON warning signal is sent via the BCAN communication when the tail lamp remains ON
with the ignition key OFF or ACC. 1.

03-28
Seat belt reminder ▶
Operating conditions for seat belt reminder are as follows: IGN ON, engine running (over 300 rpm),
vehicle speed of 25 km/h or higher, driver seat belt unfastened, passenger seat belt unfastened and
passenger seat occupied. In addition, if the seat belt reminder is activated at the speed of 25 km/h or
higher and the speed reduces to below 25 km/h within 5 minutes, the interior buzzer sound stops. The
buzzer sounds for 5 minutes again when the speed is 25 km/h or higher.
The seat belt reminder stops its operation when fastening the seat belt, but starts the operation again if
unfastening the seat belt.
If the seat belt reminder is initially operated due to unfastened driver seat belt, the buzzer sounds with
the interval of 0.02s ON/1.18s OFF, the instrument cluster sends the driver seat belt warning signal
(SBR) and the seat belt warning lamp stays on.
At this time, the buzzer sounds for 5 minutes.
If the seat belt reminder is operated due to unfastened passenger seat belt when the passenger seat
belt reminder sensor detects that the passenger seat is occupied, the instrument cluster sends the
driver seat belt warning signal and the seat belt warning lamp stays on.
For this case, the indicator shows each status of the driver and passenger seats but the indoor buzzer
is common to both seats.
If the simultaneous operating condition for the indoor buzzer is met, the driver seat has the priority.
If the driver seat belt is fastened, the same operation is also carried out in the passenger seat
automatically.
The buzzer and the warning lamp are operated according to the vehicle speed as below table during
the seat belt reminder operation. 1.
2.
3.
4.
5.
Seat belt reminder operation
<007700990090009600990090009b00a000470096008d00470089009c00a100a1008c0099004700960097008c00990088009b00900096009500610047007a0069007900470d7d00470072008c00a000470099008c009400900095008b008c00990047009e00
880099009500900095008e00470d7d0047007a009c00950099>oof warning ⇒ Tail lamp ON
<009e00880099009500900095008e00470d7d0047006f008800a100880099008b0047009e00880099009500900095008e0047008d00930088009a008f008c009900470d7d0047007b009c009900950047009a0090008e009500880093004700930088009400
970055> 6.
Buzzer Warning lamp
25 Km/h ~ 49 Km/h 0.02s ON / 1.18s OFF Keep ON
50 Km/h ~ 99 Km/h 0.02s ON / 0.98s OFF Keep ON
10 Km/h ~ 49 Km/h 0.02s ON / 0.78s OFF Keep ONFunction
Vehicle speed
Seat belt remind warning lamp (EU only)
This lamp comes on for 6 seconds after turning on the ignition switch. If the vehicle speed goes
over 10 km/h without fastened the seat belt, the inside buzzer sounds. -

03-318710-01
7) Room Lamp
Door coupled room lamp and dimming control ▶
When opening any of doors while the room lamp switch in overhead console is pressed in ("Door"
coupled position), the room lamps come on. If the key is removed and door stays open, the room lamps
automatically goes off after 10 minutes. The sleep mode will be deactivated when the door is locked or
closed with the lamp OFF automatically.
When closing the door with IGN ON, the room lamps go off immediately.
When closing the door with IGN OFF, the room lamps stays on for 2 seconds and are dimmed out for
3 seconds.
When turning the ignition switch to ON position during dimming out operation, the room lamps go off
immediately.
When receiving the door unlock signal with IGN OFF, key removed and door closed, the room lamps
come on for 30 seconds. (It operates depending on REKES unlock and manual unlock signals for
BCM with SKM.)
4. When receiving the door unlock signal again in Step (4), the overhead room lamp and center room
lamp stay on for 30 seconds additionally. (For BCM with SKM, the extension depends on the REKES
unlock signal.)
When opening a door during the linked and dimming operation, the room lamps stays ON. When
closing it again, the system performs the operation in Step (1) and (2).
When all the door switches are changed from its closing state to its opening state, the room lamps are
dimmed out. The room lamps go off immediately when entering into the theft deterrent mode. (For
BCM with SKM, door lock is carried out by the REKES lock and manual lock signals.)
The room lamps come on when the auto approach function is activated. 1.
2.
3.
4.
5.
6.
7.
8.Room lamp control by door coupled room lamp operation ▶

03-32
8) Key Hole Illumination
When opening the door with IGN OFF, the key hole lamp comes on.
When closing the door, the key hole lamp stays on for 10 seconds and goes off.
When turning the ignition switch to ON position during the operation of key hole illumination, it goes of
f
immediately.
When receiving the door lock signal (entering into theft deterrent mode), the lamp goes off.
The key hole illumination function has a priority over the immobilizer function.
If the communication with the immobilizer is interrupted, the lamp comes on for 11 seconds with the
interval of 0.5s ON/0.5s OFF regardless of the operating conditions of key hole lamp.
When turning the ignition switch to ON position in "Virgin" condition, the lamp comes on for 8 seconds
with the interval of 0.5s ON/0.5s OFF. 1.
2.
3.
4.
5.
6.
(*1) ON: IGN ON
OFF: IGN OFF(*2) Open: driver or passenger door is open
Close: driver and passenger door are closed
Room lamp OFF control ▶
The room lamps stop operating when the BCM enters into the theft deterrent or sleep mode. (This is
to prevent battery discharge if the overhead room lamp and sensor room lamp switch is ON position.)
The room lamps go off automatically 10 minutes after the key is removed. After that, if the door unlock
or all door open signal is received and the key is inserted, the sleep mode is deactivated and the room
lamps operate for another 10 minutes.
The room lamps come on when the key is inserted (BCM without SKM) or the ignition switch is turned
to "ACC" or "ON" position (BCM with SKM) while the room lamps are OFF. 1.
2.
3.

03-358710-01
10) Keyless Entry
Transmitter (REKES key) ▶
When the user operates the switch of the remote control key, the vehicle control messages formatted by
its CPU are sent to the main unit wirelessly. The, the CPU control the vehicle and the main unit controls
the vehicle operation.
Door unlock/panic buttonDoor lock
Door unlock/panic button ▶
Unlocking door and tailgate (briefly press)
If you press this button, it unlocks all doors and the tailgate and deactivates the theft deterrent mode.
When the theft deterrent mode is deactivated, the emergency hazard lights blink once.
If the door, tailgate or engine hood is not opened within 30 seconds after unlocking the door with the
remote control key in theft deterrent mode, the door is locked automatically, hazard warning flasher
blinks twice and buzzer sounds once. (entering into theft deterrent mode)
Panic function (press and hold for more than 2 sec)
When pressing (over 2 sec) the button, the hazard warning flasher blinks and buzzer sounds for
about 30 seconds.
Press the UNLOCK or PANIC button to deactivate this function. 1.
-
-
-
2.
-
-

03-38
After 30 seconds delay auto door lock ▶
If a door or tailgate is not opened within 30 seconds after unlocking the doors with remote control key
in theft deterrent mode, all doors will be automatically locked again (change to theft deterrent mode).
If any door is not opened or the key is not detected within 30 seconds after receiving the unlock
signal, the lock signal is outputted and theft deterrent mode is activated.
When entering into the theft deterrent mode, the turn signal lamps blink twice and the exterior buzzer
sounds once for SKM the lamps blink twice and burglar alarm horn sounds once for REKES. 1.
2.

03-398710-01
11) Door Lock/Unlock Control
The BCM with SKM receives wake-up source for driver door lock/unlock switch, passenger door
lock/unlock switch, rear door (left/right) lock switch, central door lock/unlock switch status through the
electric wire (hardwire).
Door lock/unlock control by door LOCK switch ▶
When moving the driver or passenger door lock (knob) switch to LOCK from UNLOCK position, BCM
sends the LOCK signal for 0.5 seconds.
When moving the driver or passenger door lock (knob) switch to UNLOCK from LOCK position, BCM
(UNLOCK) operation by the door lock (knob) switch is not available when sending the LOCK
(UNLOCK) signal by any other method such as remote control key.
When reconnecting the battery, the door lock (knob) switch is not operational regardless of the door
lock switch positions.
All doors stay unlocked when receiving the door lock signal in 0.5 seconds after closing the doors. 1.
2.
3.
4.
5.The status for key cylinder switch and latch position switch is received through the door lock/unlock
switch.
When door lock signal is outputted due to failure of the door knob switch and door open switch and
automatic unlock signal is transmitted 5 times for 1 minute, BCM forcibly lock the doors without
unlocking.
However, door unlock command works normally and deactivates forcible unlock. -