automatic SSANGYONG KORANDO 2012 Owner's Guide

03-40
Door lock/unlock control by central door lock switch ▶
When pressing the central door lock/unlock switch, BCM sends the LOCK or UNLOCK signal
according to the previous condition of driver door lock switch for 0.5 seconds.
The central door dock switch is not available when the system is in theft deterrent mode.
When turning the ignition off, all doors are automatically unlocked if any of the door lock (knob)
switches is in LOCK position.
When pressing the central door lock switch with any door open, the system unlocks the doors
immediately after locking them. 1.
2.
3.
4.
Door lock/unlock control by REKES signal ▶
When receiving the door lock signal, BCM sends the LOCK signal for 0.5 seconds.
When receiving the door unlock signal, BCM sends the UNLOCK signal for 0.5 seconds. 1.
2.

03-438710-01
Auto door lock control ▶
Door lock output is activated when the vehicle speed is maintained above 30 km/h with IGN1 ON.
However, if all the doors are locked or fail, lock output is not activated.
If any of doors is not locked after Step (1), BCM activates the door lock output up to 5 times.
If the door is still unlocked, BCM considers the door as Fail.
If the failed door is changed from UNLOCK to LOCK, the fail record the side fascia panel.
If there is any failed door, the auto door lock function is not available.
(Even though the vehicle speed is increased over 30 km/h again after decreased below 30 km/h, BCM
does not send the auto door lock signal.)
When receiving the unlock signal for another door during Step (2), BCM sends the lock
signal for the door up to 5 times.
The unlock output is activated automatically when door lock output conditions are met by this function
or the IGN1 switch is turned to OFF from ON position (even though the lock output is not activated if
the vehicle speed is maintained above 30 km/h under lock condition). (If the LOCK condition is
established with the ignition switch ON, the system outputs UNLOCK signal unconditionally when
turning the ignition switch to OFF position.)
However, whether the door lock output condition is met or not is initialized when the IGN1 switch is
turned to OFF position.
When turning the ignition off, the fail record for a door will be initialized.
If any of door lock switches is in LOCK position when turning the ignition off, all doors are unlocked. 1.
2.
3.
4.
5.
6.
7.
8.
9.
(*1) Lock: All doors including tailgate are locked.
Unlock: All doors including tailgate are unlocked.

03-498710-01
15) Theft Deterrent Alarm
Theft deterrent alarm control in BCM without SKM ▶
Entering into theft deterrent mode by REKES remote control 1.
When receiving the door lock signal with the key removed, all doors including tailgate and engine
hood closed, all doors are locked and the theft deterrent mode is activated. At this moment, the
turn signal lamps blink twice.
When pressing the lock switch on remote control key again in 4 seconds, the turn signal lamps
blink twice and the horn sounds once in the theft deterrent mode. In other words, when pressing
the door lock button once, all the doors are locked and the turn signal lamps only blink twice, and
another press in 4 seconds makes the turn signal lamps blink twice and alarm horn sound once.
When receiving the door lock signal with any door (except tailgate and engine hood) open, the
doors are unlocked immediately after locking them first.
When receiving the door lock signal with the tailgate or engine hood open, the doors are closed if
they are open, but the theft deterrent mode is not activated. However, when closing the opened
tailgate or engine hood, the theft deterrent mode is activated with two blinks of turn signal lamps.
If a door or tailgate is not opened within 30 seconds after unlocking the doors with remote control
key in theft deterrent mode, all doors will be automatically locked again (re-lock operation). When
entering into the theft deterrent mode, the turn signal lamps blink twice and the horn sounds once.
The theft deterrent mode can be activated only when the above conditions are satisfied.
Ex) The theft deterrent mode cannot be activated when locking the doors with key hole on door. -
-
-
-
-
-

03-618710-01
Emergency hazard flasher control (coupled with ABS) ▶
System layout 1.
Operating conditions: When receiving the emergency hazard flasher ON signal from ESP and ABS.
When receiving the emergency stop signal through PCAN communication it blinks with the interval of
4 Hz and when receiving the emergency stop OFF signal through PCAN communication it blinks with
the interval of 1.25 Hz, normal operating speed.
However, the manual operation of the switch has a priority over this function. 2.
Priority
Manual hazard flasher > Emergency stop signal > Emergency auto hazard flasher > Auto hazard
flasher
(If emergency stop signal is received through PCAN communication during hazard flasher
operation, the signal is overridden. If the emergency hazard flasher signal is received during multi-
function automatic hazard flasher operation or multi-function automatic hazard flasher is received
during emergency hazard flasher operation, emergency stop is performed.)
When the emergency stop signal is received, the hazard flasher blinks with the interval of 4 Hz,
then returns to normal operation speed. After that, if the emergency stop signal is received again,
the emergency hazard flasher blinks with the interval of 4 times/sec. -
-

03-62
The emergency hazard flasher does not operate if the vehicle speed is over 50 km/h when the
emergency stop signal is received.
The emergency hazard flasher operates if the vehicle speed is 50 km/h or lower when the
emergency stop signal is received.
When vehicle speed increases more than 10 km/h above the speed when the signal is received
during operation by emergency braking signal, the emergency hazard flasher stops operation.
When turning emergency hazard flasher switch OFF during operation by emergency braking
signal, it stops operation.
It is deactivated automatically 10 seconds after if items 2) and 3) above are not met during
operation by emergency braking signal.
If multi-function automatic hazard flasher signal is received during operation by emergency
braking signal, it will be overridden. 1)
2)
3)
4)
5)
6) OFF conditions:
The BCM flashes the emergency auto hazard flasher with interval of 1.25 times/sec.: 3.

03-638710-01
19) DRL (Daytime Running Light) Control
When receiving the DRL activation signal, the tail lamps are turned ON when turning the ignition
switch to ON position, and the headlamps are turned ON when the engine speed is 300 rpm or
higher.
When turning ON the tail lamp switch during engine running, the headlamps are turned OFF.
The headlamps do not come ON when the engine speed is above 300 rpm with the tail lamp switch
ON.
The auto light sensor is not available in the vehicle with DRL system.
If there is no DRL activation signal, the light system operates in normal conditions. 1.
2.
3.
4.
5.
20) Fog Lamp Control
When pressing the rear fog lamp switch with IGN2 ON (headlamp ON condition), the rear fog lamps
are turned ON. When pressing the rear fog lamp switch again during the operation, the rear fog lamps
are turned OFF.
The rear fog lamps do not come ON when the IGN2 switch is turned to OFF position or the light
switch is OFF.
The rear fog lamps should not automatically come on again if they have been turned OFF by any
other way other than the switch. 1.
2.
3.
(The rear fog lamps are applied to only EU region)

03-66
Auto folding/unfolding control ▶
Setting 1.
Set auto folding function: When pressing the mirror folding switch for over 3 seconds, the auto
folding function is set and the internal buzzer sounds once (ON: 0.1 sec, OFF: 0.2 sec).
Release auto folding function: When pressing the mirror folding switch for over 3 seconds, the
auto folding function is set and the internal buzzer sounds twice (ON: 0.1 sec, OFF: 0.2 sec). -
-
Auto folding sequence 2.
When receiving the LOCK signal from the REKES, the system operates in the sequence of "Door
<00930096008a0092004702e70047007b008f008c008d009b0047008b008c009b008c00990099008c0095009b004700940096008b008c00470088008a009b0090009d0088009b009000960095004702e700470074009000990099009600990047008d009600
93008b00900095008e00490047008d0096009900470069006a>M without SKM.
When receiving the outside door handle switch signal or door lock signal from the smart key
<0099008c00940096009b008c0047008a00960095009b00990096009300530047009b008f008c0047009a00a0009a009b008c0094004700960097008c00990088009b008c009a0047009000950047009b008f008c0047009a008c0098009c008c0095008a00
8c00470096008d0047006b009600960099004700930096008a>k → Theft deterrent mode
activation → Mirror folding" for BCM with SKM. -
-
When the auto folding function is set, the automatic unfolding is not available if the mirrors have been
folded manually.
(The outside rearview mirror will be folded automatically if the auto folding function is set.)
The factory setting is the enabling the auto folding function. 4.
5.
23) Approach (Puddle) Lamp Control
Without SKM ▶
Approach lamp ON 1.
When receiving the UNLOCK signal in the theft deterrent mode, the approach lamps come
ON for 30 seconds.
When turning the ignition switch to OFF from ON position and opening the driver door, the
approach lamps come ON. -
-
Approach lamp OFF 2.
When receiving the door lock signal with the approach lamps ON, the lamps go OFF
(reactivation of theft deterrent mode).
When turning the ignition switch to ON position with the approach lamps ON, the lamps go OFF.
The approach lamps go OFF after 30 seconds. -
-
- Auto unfolding sequence 3.
When receiving the UNLOCK signal from the REKES, the system operates in the sequence of
<0049006b0096009600990047009c009500930096008a0092004702e70047007b008f008c008d009b0047008b008c009b008c00990099008c0095009b004700940096008b008c0047008b008c0088008a009b0090009d0088009b009000960095004702e700
470074009000990099009600990047009c0095008d00960093>ding" for BCM without
SKM.
When receiving the outside door handle switch signal or door unlock signal from the smart key
<0099008c00940096009b008c0047008a00960095009b00990096009300530047009b008f008c0047009a00a0009a009b008c0094004700960097008c00990088009b008c009a0047009000950047009b008f008c0047009a008c0098009c008c0095008a00
8c00470096008d0047006b0096009600990047009c00950093>ock → Theft deterrent
<00940096008b008c0047008b008c0088008a009b0090009d0088009b009000960095004702e700470074009000990099009600990047009c0095008d00960093008b00900095008e00490047008d0096009900470069006a00740047009e0090009b008f00
47007a007200740055> -
-

05-58010-01
Previous Current
Ambient temperature also displayed on vehicle with manual A/C control switch
Both SVC and STD class
Previous Current
Warning lamp symbols fulfil ISO standards used on all models
(e.g. 4WD CHECK indicator symbol)
4) Warning lamps according to ISO standards
5) Ambient temperature display
SVC class
This is displayed for 2 seconds when activating winter mode, displayed for 2 seconds when deactivating
winter mode and displayed for 4 seconds when starting engine and driving off (DOT LCD message).
AutomaticAutomatic
Manual
SVC classSVC class
STD class

05-6
SVC class
Previous Current
Changed from figure type to bar graph type.
6) Average fuel economy reset and calibrated automatically when
refilling
7) Instant fuel consumption display changed
8) Pre-warning indicator for engine overheat removed
Both SVC and STD class
Previous Current
Reset by user Reset by user and automatic reset when refilling
9) TDMS logic changed
SVC class
Current
TDMS (Tier Direction Management System) is not displayed when EPS warning lamp comes on.
SVC class STD class
Pre-warning indicator for engine overheat is removed.
EPS warning lampTDMS displayLCD not displayed
EPS warning lamp
comes onLCD screen is not
displayed.

05-398010-01
Function Signal Remark
Display type 3 digits LCD
Display range 0.0 km ~ 99.9 km
(0 miles~99.9 miles)
Resolution 0.1 km (mile)
Display interval every 10 seconds
Data clear - Disconnect B+
voltage
- Press and hold Reset
switch for more than
1 sec.
- Reset automatically
when refilling
(2) Average Fuel Consumption Mode
The LCD display indicates average fuel consumption calculated based on total driving distance and total
fuel consumption since B+ power supply or data reset.
(3) Instant Fuel Consumption Mode
The LCD display indicates the instant fuel consumption (for 2 seconds) calculated based on driving
distance and fuel consumption for last 2 seconds.
Function Signal Remark
Display type 3 digits LCD
Display range 0.0 ~ 99.9
(MPG, ℓ/100 km, km/ℓ)
Resolution 0.1 km (mile)
Display interval every 2 seconds