warning SSANGYONG KORANDO 2013 Repair Manual

8010-01
1) SVC
3. DESCRIPTION OF WARNING LAMPS & INDICATORS

8010-01
Indicator
(green)
Headlamp high beam indicator
Front fog lamp indicator
Side light indicator
Indicator
(blue)
Indicator
(green)
Indicator
(amber)
Glow indicator(DSL only)
Indicator
(red)
Fuel filter indicator(DSL only)
This indicator comes on when the tail lamp is switched on.
This indicator comes on when the ignition switch is turned to the "ON"
position and will go off when the glow plugs are sufficiently heated.
This indicator comes on when the water level in the fuel filter exceeds a
certain level. This lamp comes on when the headlamp high beam is operated.
This indicator comes on when the fog lamp switch is operated after the tail
lamps comes on.
3) Details of Warning Lamps and Indicators

Low fuel level warning lamp
Warning lamp
(amber)
Engine overheat warning lamp
Warning lamp
(red)
Door ajar
Warning lamp
(red)
Seat belt reminder
Warning lamp
(red)
Air bag
Warning lamp
(red)
However, the fuel level may change slight depending on vehicle
condition, inclination of the road, etc. Also, it blinks if there is a short or
open circuit between the fuel level sensor and cluster.
interval of 1 second, a message is displayed, the warning sounds once
through the speaker and the buzzer sounds at an interval of 0.5 seconds.
This lamp comes on when any door is open or not closed completely.
(both STD and SVC class)
This lamp comes on when the ignition switch is pressed ON.
It keeps coming on if the driver's seat belt is not fastened.
This lamp comes on when the ignition switch is pressed to the ON mode.
Then, it goes off if the system is normal.
If this lamp stays on while driving, it means that the air bag system is faulty.

8010-01
Indicator
(amber)
ESP
ESP OFF indicator
Engine check warning lamp
Indicator
(amber)
Indicator
(amber)
Indicator (red)
Battery charge warning lamp
Indicator (red)
Engine oil level warning lamp
This lamp comes on if any sensor or device related to the engine control is
defective.
This lamp comes on when the start switch is ON or when the battery level is
low.
(For EEM, warning lamp is controlled according to CAN signal)
This lamp comes on when the ignition switch is turned to "ON" position,
and then goes off if the engine oil level is normal.
If the engine oil level warning lamp comes on while driving, check the
engine oil level and oil leakage. -
- This indicator comes on when the ESP system is faulty.
This indicator comes on when pressing the ESP OFF switch.

Indicator
(amber)
Brake warning lamp (brake fluid)
ABS warning lamp
Passenger air bag disable indicator
Indicator
(red)
Indicator
(amber)
Indicator
(red)
EPS
Indicator
(amber)
Immobilizer indicator
This indicator comes on when the passenger air bag OFF switch is operated.
This indicator comes on the immobilizer (transponder) is not certified. This lamp comes on when the parking brake is applied or the brake fluid
is insufficient.
If this lamp doesn't go off after the parking brake is released, check the
brake fluid level first and then fluid leakage. -
-
This warning light comes on when the ignition switch is turned to ON
and should go out if the system is normal -
This indicator comes on when the EPS system is faulty.

8010-01
Indicator
(green)
Hazard indicator
ECO indicator
Cruise control indicator
Indicator
(red)
Indicator
(green)
Indicator
(green)
4WD LOCK indicator
Indicator
(red)
4WD check warning lamp
This indicator comes on when the cruise control system is activated.
This indicator goes off when the brake pedal is depressed. (auto cruise
deactivated)
This warning lamp comes on when the 4WD LOCK switch is pressed.
This indicator goes off when pressing the switch again.
This warning lamp comes on when the 4WD system is defective. This indicator comes on when the hazard warning flashers are switched on.
(applies to STD class)
This indicator comes on when the ECO cruise system is activated.
This indicator goes off when the brake pedal is depressed. (ECO
deactivated)

Indicator
(green)
Passenger seat belt reminder
Left turn signal indicator
Right turn signal indicator
Indicator
(red)
Indicator
(green)
Indicator
(green)
Winter mode indicator(DSL only)
The right turn signal indicator blinks if the light switch is pushed up to
the right, and both turn signal indicators blink if the hazard warning flasher
switch is pressed.
When the mode switch is pressed, the winter mode is selected and the
winter mode indicator comes on on the instrument cluster. The winter
mode is used to start off on a slippery road with the 2nd gear. If the switch
is pressed again, the winter mode is deactivated and system returns to
standard mode.This indicator comes on when the ignition switch is turned to the "ON"
position and goes off when the passenger's seat belt is fastened.
The left turn signal indicator blinks if the light switch is pushed down to the
left, and both turn signal indicators blink if the hazard warning flasher switch
is pressed.
Smart key warning lamp
Indicator
(amber)
This lamp comes on when the uncertified transponder or smart key is
detected,
SKM system is defective or there is no smart key in the vehicle.

8010-01
Indicator
(amber)
Steering wheel heating indicator
This indicator comes on when the steering wheel heating switch
is operated with the ignition switch turned on and the engine running.
(applies to SVC class)
TPMS WARNING LIGHT
Indicator
(amber)
GLOBAL WARNING LIGHT
Indicator
(amber)
GSI (GEAR SHIFT INDICATOR)
This warning light comes on when the ignition switch is turned to
this warning light comes on.
This warning light comes on when the ignition switch is turned to
If the tire pressure is too low, this warning light blinks for 70 seconds and
then ON.
This indicator indicates the proper gear shifting time.
Shift-up to 3rd gear (currently 2nd gear or lower)
Shift-down to 3rd gear (currently 4th gear or higher)
If the system is properly working, this indicator is invisible.Ex)

8010-01
Operations for power supply in SVC
When the ignition switch is turned to ON position, the message "WELCOME" is displayed for 2
seconds on the DOT LCD and the seat belt reminder comes on for 4 seconds. However, if a signal
with higher priority is received, the seat belt reminder comes on only for 2 seconds
to display it.
The pre-warning (system check) indicator comes on for 4 seconds and goes off 0.4 seconds after
that the ignition is switched on.
All input signals can be input 4 seconds after the pre-warning (system check) indicator starts
illuminating.
Only the symbol and DOT LCD are illuminated initially, if the SKM (Smart Key Module) or door (B-
CAN) signal is received
while B+ power is supplied.
If the ignition is switched on with the LCD illuminated, the DOT LCD and the symbol follow
the side fascia panel.
When the step 1, 2 and 3 are performed after 4 seconds, the seat belt warning lamp is deactivated
in advance.
Dial light ON condition: Lights up gradually for 2 seconds when the ignition is switched on. 1.
2.
3.
4.
5.
6.
4) Illumination & Brightness
(1) Operations for Power Supply

8010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch to
ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.