warning SSANGYONG KORANDO 2013 Manual Online

8510-00
Windshield heating switch
Press this switch to operate the windshield
heating system for 12 minutes. Press the
switch again to stop the system. The
heated glass will operate for about 6
minutes when the switch is pressed again
within 10 minutes after completion of its
first operation cycle. The indicator lamp for
the switch comes on when the heating is
on.
Hazard warning flasher switch
When the driver presses the switch, all the
turn signal lamps flash regardless of the
ignition switch status. Pressing the switch
again turns off the turn signal lamps. The turn
signal lamp does not operate while the
hazard warning flasher operates.
TRIP/RESET switch
Whenever pressing this button, the information is
displayed in the following order: Odometer, Trip
A, Trip B, Distance to empty, Average fuel
economy, Instant fuel economy, Illumination level,
Tire pressure (with TPMS), Ambient air
temperature (for STD); Trip A, Trip B, Distance to
empty, Average fuel economy/Instant fuel
economy, Illumination level, Tire pressure (with
TPMS), Ambient air temperature (for SVC). Press
and hold this button to initialize (reset) Trip A/Trip
B and average fuel consumption, adjust
illumination level or change the unit of
temperature.
Description
Rear glass/outside rearview mirror heating
switch
Press this switch to operate the rear glass and
outside rearview mirror heating system for 12
minutes. Press the switch again to stop the
system. The heated glass will operate for about 6
minutes when the switch is pressed again within
10 minutes after completion of its first operation
cycle. The indicator lamp for the switch comes on
when the heating is on.
The switch is operable only when the engine
is started.
The hazard warning flasher blinks
during emergency hazard warning
lamp control and air bag deployment
signal activation.
The switch is operable only when the
engine is started.

8510-00
Operation process
When the driver presses the switch, all the turn signal lamps flash regardless of the ignition switch status.
Pressing the switch again turns off the turn signal lamps. The turn signal lamp does not operate while the
hazard warning flasher operates.
Hazard warning flasher switch
(4) Hazard warning flasher switch
The hazard warning flasher blinks during emergency hazard warning lamp control and air bag
deployment signal activation.

Initialization mode after IGN ON, ESP disabled due to failure, during ESP operation (blink), under
diagnostic mode, indicator lamp ON in instrument cluster, impossible to communicate with CAN
module. -ESP warning lamp module
The ESP warning lamp shows self-diagnosis result of ESP function and whether there is a fault. The
ESP warning lamp comes on when:

8510-00
Multifunction wiper switches
2) Multifunction Switch
Multifunction light switches
Light switch
Front wiper switch
Wiper speed dial
Rear wiper switch Front fog lamp switch
Front auto washer switch The multifunction switch contains the auto washer and wiper switch, front fog lamp switch and auto
hazard warning flasher switch. For the vehicle with air bag, since the contact coil is fitted to the upper part
of the multifunction switch and ESP steering wheel angle sensor is fitted to upper part of the contact coil,
pay attention to when removing and fitting or checking the wiring.

Sunroof warning control
When removing the ignition key with the sunroof open (without SKM) or when opening the driver door
with IGN OFF or ACC and sunroof open (with SKM), the indoor buzzer sounds for 10 seconds with
the interval of 0.02s ON/1.58s OFF.
When opening and closing the driver door or closing the sunroof during indoor buzzer operation, the
buzzer stops its operation immediately.
When closing the driver door or sunroof and opening again during warning operation, the sunroof
warning does not work. If the condition is met after the ignition switch is turned to "ON" position again,
the indoor buzzer sounds for 10 seconds with the interval of 0.02s ON/1.58s OFF.
The sunroof warning has a priority over the tail lamp ON warning. 1.
2.
3.
4.

8310-00
(2) Tail lamp
Front
Rear
Tail lamp
Tail lamp
The tail lamp is operated by the BCM when the BCM receives a signal from the multifunction switch.
Tail lamp warning
The buzzer sounds for 10 seconds with the interval of 0.02 s ON and 1.38 s OFF when opening the
driver door with the key removed (without SKM)/with IGN OFF or ACC (with SKM) and tail lamp ON.
The buzzer stops its operation when turning off the tail lamp or closing the driver door during buzzer
operation. The buzzer stays ON when turning the tail lamp on again after turning it off during buzzer
operation. 1.
2.
Tail lamp auto turn-off
When opening and closing the driver door after turning off the ignition with the tail lamp ON, the tail
lamps go off automatically.
The tail lamps come on again when inserting the ignition key (without SKM) and turning on the ignition
(with SKM) after tail lamp auto OFF.
The tail lamp should not go off when turning on the tail lamp switch with the ignition key removed
(without SKM) and with power off or ACC ON (with SKM). -
-
-

8790-00
While reversing, if obstacles are within stage 1, the warning beep sounds with long intervals. If within
stage 2, the warning beep sounds with short intervals and if within stage 3, the warning beep sounds
continuously.
Sensor detection range
Within 20 cm from the ground
(Objects may not be detected in this range.)
Buzzer interval when measuring distance
2) Rear PAS Sensor

4. OUTPUT SPECIFICATIONS FOR SENSOR SELF-
DIAGNOSIS BUZZER SOUND
Fail condition (However, no obstacle should be within 30 cm)
1. The signal wire is open
2. The power wire (+ and -)is open -Conditions to "FAIL" in sensor diagnosis
Buzzer interval during self diagnosis
Timeout processing time for buzzer interval after measuring distance/self diagnosis: 600 ms
- If timeout is reached, the PAS returns to undetected condition.
Process while re-inputting
- After timeout, the process is performed normally if the signal required for display is received
from beginning to end. (not detectable if the signal is received in the midst of process) 1.
2.Exception/error handling
Self diagnosis is performed once when the ignition is switched on (gear shift lever in "R" position). If the
system is defective (Fail) due to open sensor or communication problem, the information for the failed
sensor is displayed as buzzer sound.
If it is normal, the warning buzzer sounds for 60 ms.

8910-05
2. CAUTIONS AND WARNING FOR SAFETY
This mark indicates potentially hazardous situation which, if not observed, may result in serious
injury and material damage.
Ssangyong is not liable for any personal injury and material damage, caused by violation of traffic
regulations or neglect of observing actual traffic and driving situations.
Colors on display figures in this manual may differ from actual display due to publication concerns. -
-
-
This mark indicates situation which, if not observed, may result in an accident or system
malfunction.
Do not disassemble or modify this system.
If doing so, it may cause an accident, fire or electric shock.
Do not use the system if it is malfunctioning (sound or video output problem).
Doing so may lead to an accident or electric shock.
Please contact a Ssangyong service dealer immediately.
The system should be used only when the engine is started.
Using the system for an extended period of the with the engine off may discharge the battery.
Do not leave beverages or foreign materials around the system.
If they enter the system, they may cause a fire.
The system may break down if a disc not supported by this system is inserted.
Do not apply impact to or drop this system.
It might cause malfunction.
Never leave the system in a hot or cold place for an extended period of time. Therefore, do not
-
-
-
-
-
-
-
-

Newly added TPMS (Tire Pressure Monitoring System)
TPMS related warning lamp
TPMS warning lamp Global warning lamp
- TPMS warning lamp: Comes on if an error occurs in any component
related to the TPMS regardless of tire inflation pressure.
- Global warning lamp: Comes on when the tire pressure is low.
DOT LCD display window (supervision
type)
Displays current tire pressure and
abnormality.