SSANGYONG KORANDO 2013 Service Manual

8010-01
Indicator
(green)
Hazard indicator
ECO indicator
Cruise control indicator
Indicator
(red)
Indicator
(green)
Indicator
(green)
4WD LOCK indicator
Indicator
(red)
4WD check warning lamp
This indicator comes on when the cruise control system is activated.
This indicator goes off when the brake pedal is depressed. (auto cruise
deactivated)
This warning lamp comes on when the 4WD LOCK switch is pressed.
This indicator goes off when pressing the switch again.
This warning lamp comes on when the 4WD system is defective. This indicator comes on when the hazard warning flashers are switched on.
(applies to STD class)
This indicator comes on when the ECO cruise system is activated.
This indicator goes off when the brake pedal is depressed. (ECO
deactivated)

Indicator
(green)
Passenger seat belt reminder
Left turn signal indicator
Right turn signal indicator
Indicator
(red)
Indicator
(green)
Indicator
(green)
Winter mode indicator(DSL only)
The right turn signal indicator blinks if the light switch is pushed up to
the right, and both turn signal indicators blink if the hazard warning flasher
switch is pressed.
When the mode switch is pressed, the winter mode is selected and the
winter mode indicator comes on on the instrument cluster. The winter
mode is used to start off on a slippery road with the 2nd gear. If the switch
is pressed again, the winter mode is deactivated and system returns to
standard mode.This indicator comes on when the ignition switch is turned to the "ON"
position and goes off when the passenger's seat belt is fastened.
The left turn signal indicator blinks if the light switch is pushed down to the
left, and both turn signal indicators blink if the hazard warning flasher switch
is pressed.
Smart key warning lamp
Indicator
(amber)
This lamp comes on when the uncertified transponder or smart key is
detected,
SKM system is defective or there is no smart key in the vehicle.

8010-01
Indicator
(amber)
Steering wheel heating indicator
This indicator comes on when the steering wheel heating switch
is operated with the ignition switch turned on and the engine running.
(applies to SVC class)
TPMS WARNING LIGHT
Indicator
(amber)
GLOBAL WARNING LIGHT
Indicator
(amber)
GSI (GEAR SHIFT INDICATOR)
This warning light comes on when the ignition switch is turned to
this warning light comes on.
This warning light comes on when the ignition switch is turned to
If the tire pressure is too low, this warning light blinks for 70 seconds and
then ON.
This indicator indicates the proper gear shifting time.
Shift-up to 3rd gear (currently 2nd gear or lower)
Shift-down to 3rd gear (currently 4th gear or higher)
If the system is properly working, this indicator is invisible.Ex)

1) SVC
4. OPERATING PROCESS
2) STD

8010-01
3) Display Sequence
Display sequence for STD main LCD & SVC DOT LCD

Operating time of
Trip switchFunction
Below 1 second
(60 to 980 ms)STD Mode change
SVC Mode change
Over 1 seconds Reset function (Trip A, B, AFC)
Over 3 seconds -
ReadyMode change
If the Trip/Reset switch is not pressed within 3 seconds after getting into the illumination mode and the
ambient air temperature mode, the LCD changes to next mode.
The factory-setting mode is DTE (Distance To Empty) mode. *
*

8010-01
Operations for power supply in SVC
When the ignition switch is turned to ON position, the message "WELCOME" is displayed for 2
seconds on the DOT LCD and the seat belt reminder comes on for 4 seconds. However, if a signal
with higher priority is received, the seat belt reminder comes on only for 2 seconds
to display it.
The pre-warning (system check) indicator comes on for 4 seconds and goes off 0.4 seconds after
that the ignition is switched on.
All input signals can be input 4 seconds after the pre-warning (system check) indicator starts
illuminating.
Only the symbol and DOT LCD are illuminated initially, if the SKM (Smart Key Module) or door (B-
CAN) signal is received
while B+ power is supplied.
If the ignition is switched on with the LCD illuminated, the DOT LCD and the symbol follow
the side fascia panel.
When the step 1, 2 and 3 are performed after 4 seconds, the seat belt warning lamp is deactivated
in advance.
Dial light ON condition: Lights up gradually for 2 seconds when the ignition is switched on. 1.
2.
3.
4.
5.
6.
4) Illumination & Brightness
(1) Operations for Power Supply

When the ignition is switched off, the message "GOOD-BYE" is displayed for 2 seconds and disappears.
The other LCDs go off as soon as the ignition is switched off.
The dial and pointer dim down for 2 seconds and go off at the same time when the DOT LCD goes off. 7.

8010-01
Operations for power supply in STD
The operation input before the LCD backlight is illuminated, right after the ignition is turned OFF or ON,
is ignored.
detected.
The LCD display, LCD backlight, dial lamp and indicator lamp are turned on or off by the ignition
switch ON/OFF operation. -
-
-

Brightness in SVC
(2) Illumination Level
Brightness in STD
Operating power Illumination levelMain LCD, dial point
Day Night
B+
(B-CAN Wake UP) - OFF OFF
IGN 1 Level 1 100% 20%
Level 2 100% 30%
Level 3 100% 40%
Level 4 100% 50%
Level 5 100% 60%
Level 6 100% 70%
Illumination
levelDOT LCDODO, gauge LCD, dial pointer
Day Night Day Night
B+(B-CAN
Wake UP) Initial
time
-Level 6 Level 6OFF (however, level 6 for initial
operation with B+ & IGN1 ON)
After
initial
timeMaintain
previous
levelMaintain
previous
levelOFF (however, maintains
previous level for initial operation
with B+ & IGN1 ON)
IGN 1 Level 1 25% 5% 25% 5%
Level 2 40% 12% 40% 12%
Level 3 55% 19% 55% 19%
Level 4 70% 26% 70% 26%
Level 5 85% 33% 85% 33%
Level 6 100% 40% 100% 40% Operating power
IGN 1