torque SSANGYONG MUSSO 1998 Workshop Owner's Guide

M162 ENGINE MECHANICAL 1B1-37
7. Remove the cylinder head bolts in numerical order.
Installation Notice
8. Check the length of the cylinder head bolt.
Installation Notice
Box Wrench Insert 000 589 01 10 00
lReplace the bolt if the measured length exceed the
max. length.
lApply the oil to the thread surface of bolt.
9. Carefully remove the cylinder head and check the mating
surface.
10. Installation should follow the removal procedure in the
reverse order. 6. Remove the guide rail fixing pin from the cylinder head using
the sliding hammer (01) and the threaded pin (02).
Sliding Hammer 116 589 20 33 00
Threaded Pin 116 589 02 34 00
Tightening Torque1st step 55 Nm
2nd step 9 0 °
3rd step 9 0 °
Length (L)New 160 ± 0.8 mm
Max. 162 ± 0.7 mm

1B1-38 M162 ENGINE MECHANICAL
TIMING GEAR CASE COVER
Preceding Work : Removal of cylinder head front cover
Removal of alternator bracket
Removal of tensioning device
Removal of belt pulley and vibration damper
1 Bolt (M8 x 60, 3 pieces).................22.5-27.5 Nm
2 A/C Bracket
3 Bolt (M8 x 65, 3 pieces).................22.5-27.5 Nm
4 Bolt (M8 x 40, 1 piece)...................22.5-27.5 Nm
5 Bolt (M8 x 60, 1 piece)...................22.5-27.5 Nm6 Seal
7 Timing Gear Case Cover
8 Roll Pin
9 Bolt (M6 x 22, 6 pieces)......................... 9-11 Nm
Removal & Installation Procedure
1. Put the alignment marks (arrows) on the timing chain and
camshaft sprocket.
2. Unscrew the A/C bracket bolts (1) and remove the bracket.
Installation Notice
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE MECHANICAL 1B1-39
3. Remove the cooling fan and the viscous clutch. Unscrew
the three bolts from the cooling fan bracket and remove the
bracket (arrows).
Installation Notice
4. Remove the timing gear case cover after unscrewing the
bolts (3) and (4) from the timing gear case cover and the
bolt (9) from the oil pan.
Notice
Be careful not to damage the oil pan gasket.
Installation Notice
lApply the sealant after cleaning the timing gear case
cover surface.
lBe careful not to stain the oil chamber of chain tensioner
with the sealant.
5. Installation should follow the removal procedure in the
reverse order.
6. Warm up the engine and check for oil leaks.
Tightening Torque 22.5 - 27.5 Nm
Tightening TorqueBolt (3,4) 22.5 - 27.5 Nm
Bolt (9) 9 - 11 Nm

M162 ENGINE MECHANICAL 1B1-41
Tools Required
601 589 03 43 00 Sleeve
Removal & Installation Procedure
1. Unscrew the bolts (1) and (5) and remove the closing cover
by pulling the rear cover lug (arrows).
Notice
Be careful not to damage the oil pan gasket.
2. Clean the sealing surface of the crankcase and the rear
sealing cover.
3. Check the radial shaft seal and replace it if necessary.
4. Apply the Loctite 573 to the rear cover sealing surface.
5. Apply the engine oil to the dust lip of the radial shaft seal.
Notice
Do not use the grease.
6. Using the special tool, press the radial shaft seal and the
rear cover.
7. Tighten the rear cover bolt (1) and then tighten the oil pan
bolt (5) as specified and remove the special tool.
Installation Notice
Seal Assembler 601 589 03 43 00
Tightening Torque(Bolt 1,5) 9 - 11 Nm

1B1-44 M162 ENGINE MECHANICAL
Engine Lock 602 589 00 40 00
2. Remove the start motor and install the engine lock to the
flywheel ring gear.
3. Remove the center bolt.
Installation Notice
Tightening Torque1st step 200 - 220 Nm
2nd step 90° +10°
4. Remove the vibration damper assembly using the puller.
5. Installation should follow the removal procedure in the
reverse order.
Notice
If possible, don’t separate the vibration damper and the
pulley.

M162 ENGINE MECHANICAL 1B1-45
CRANKSHAFT FRONT RADIAL SEAL
Preceding Work : Removal of belt pulley and vibration damper
1 Center Bolt (M18 x 50)
................................ 1st step 200-220 Nm
2nd step 90° +10°
2 Center Bolt Washer
3 Sleeve (Special Tool)
4 Crankshaft Front Seal
5 Key
Tools Required
601 589 03 14 00 Sleeve
Replacement Procedure
1. Remove the radial seal with a screw driver.
Notice
Use a clean cloth not to damage the radial seal mounting
hole and the crankshaft.
5. Remove the sleeve and install the belt pulley and the
vibration damper.
6. Check for leaks while operating the engine. 2. Coat the radial sealing lip with engine oil.
3. Using the sleeve, assemble the radial seal .
4. Align the sleeve groove and the woodruff key and tighten
the center bolt until the center bolt and the damper disk
stop in the movement.
Installation Notice
Tightening Torque1st step 200 - 220Nm
2nd step 90° + 10°

1B1-50 M162 ENGINE MECHANICAL
Installation Notice
lMake sure the crankshaft bearing cap properly seated
in place in the crankcase side. When perfectly installed,
the projected part (arrow) locates in the left side (intake
manifold side).
lAssemble so that the projected part of the cap and
crankcase face the same direction.
Removal & Installation Procedure
1. Unscrew the connecting rod bearing cap bolt and remove
the bearing cap.
Installation Notice
2. Unscrew the crankshaft bearing cap bolts and separate the
upper and lower bearing shells and thrust washers.
Installation Notice
lRemove the bearing cap from front (pulley side) to rear.
lMake sure that the upper and lower bearing shells do
not change each other and coat with engine oil.
lThe oil grooves (arrows) in the thrust washers must face
outward and insert the thrust bearing into the bearing
cap.
lThere are five kinds of thrust washers by thickness. Select
the proper washer when repaired.
3. Remove the crankshaft.
4. Installation should follow the removal procedure in the
reverse order.
5. After completion of the installation, check for the rotating
condition of the crankshaft.
lMake sure that the upper and lower bearing shells do
not change each other.
lCoat the bearing shell with engine oil.
lInstall the bearing cap according to the consecutive
number.
Part No. : 601 030 00 622.15 mm
Part No. : 601 030 01 622.20 mm
Part No. : 601 030 02 622.25 mm
Part No. : 601 030 03 622.30 mm
Part No. : 601 030 04 622.40 mm
Tightening Torque 40 Nm + 90°
Tightening Torque 55 Nm + 90°

M162 ENGINE MECHANICAL 1B1-53
FLYWHEEL / DRIVEN PLATE
Preceding Work : Removal of manual or automatic transmission
1 Flywheel Mounting Bolt (M10 x 22, 8 pieces)
...............................................1st step 45+5 Nm
2nd step +90° +10°
2 Plate3 Driven Plate (A/T)
4 Dowel Pin
Service Data Standard (Stretch Bolt)
Nominal Size
Stretch Side Diameter
Bolt Length
Tightening TorqueM x 1.5
8.5 - 0.2 mm
8.0 mm
21.8 - 22.2 mm-
When New
Min. Diameter
When NewD
d
L
1st step 50 Nm, 2nd step 90°

1B1-54 M162 ENGINE MECHANICAL
Removal & Installation Procedure
1. Unscrew the stretch bolt.
Installation Notice
Sectional View
1 Oil Pan
2 Cover
3 Crankshaft Front Seal
4 Flywheel MTG Bolt
5 Crankshaft
6 Dowel Pin
7 Plate
8 TGCC
9 Bolt
10 Front Drive Plate
11 Rear Drive Plate
12 Rivet
13 Segment
14 Ring Gear
lReplace the bolt when the stretch side diameter (d) of
the flywheel mounting bolt is less than 8.0mm.
lFor the stretch bolt tightening, keep the socket wrench
and Tommy-bar to be 90° and tighten as specified.
2. Remove the flywheel for manual transmission vehicles, or
the driven plate (3), and plate (2) for Auto. transmission
vehicle.
3. Installation should follow the removal procedure in the
reverse order.Tightening Torque1st step 45+5 Nm
2nd step 90° + 10°

1B1-56 M162 ENGINE MECHANICAL
Removal & Installation Procedure
1. Turn the crankshaft to the direction of engine rotation and
position the no.1 cylinder piston at TDC which the camshaft
is positioned at OT.
2. Remove the cylinder head front cover.
3. Paint the alignment marks (arrows) on the intake and
exhaust camshaft sprocket and the timing chain.
4. Unscrew the bolt (3) from the armature (4) and remove the
armature.
Installation Notice
3 Bolt
4 Amarture
6 Nut (M20 x 1.5)
11 Seal Cover
5. Unscrew the nut (6) and remove the ring and seal cover
(11).
Installation Notice
Tightening Torque 35 Nm
Tightening Torque 60 - 70 Nm
12 Camshaft Sprocket
17 Control Piston
21 Intake Camshaft
6. Unscrew the sprocket bolt from the exhaust camshaft and
remove the sprocket.
Installation Notice
The sprocket bolt is designed to be used only once, so
always replace with new one.Tightening Torque1st step 18 - 22 Nm
2nd step 90° ± 5°